Amana Washing Machine Not Spinning [Solution]

Is your Amana washing machine not spinning? If so, this guide is for you. We’ll be explaining the most common causes of this problem and providing steps on how to resolve them…

Amana Washing Machine Not Spinning — How To Fix

Is your Amana washing machine not spinning? here are the faults you should look for…

1. Drive Belt Damaged

Your washing machine will not be able to spin if the drive belt gets worn or broken. To replace the belt in your Amana washing machine, these are the steps you’ll need to take…

Changing A Worn Belt In Amana Top Loader Washing Machine

Replace a worn belt in your top loader washing machine with the following steps…

Step 1. In order to prevent water leaks or electrical damage, make sure your machine is disconnected from the electrical supply and the water valve is turned off before starting this repair.

Step 2. Unplug the two water supply hoses from the back of your washer (water will leak out, so ensure that you have a rag nearby).

Step 3. Release the spring clamp on the drain hose at the back of the appliance. Pull the hose off the machine.

Step 4. Secure the lid of your machine using some tape. With someone’s assistance, tilt your washer backwards carefully and lay it on the floor.

Step 5. With a 5/16 nut-driver, loosen the nuts holding the belt guard. Take the belt guard off the machine.

Step 6. If still intact, remove the drive belt from the motor pulley and transmission pulley.

Step 7. Remove your new washing machine belt from its packaging. With the grooved side turned inwards, loop the new belt around the two pulleys. Place the belt guard over the pulleys and secure it with the screws.

Step 8. Carefully lift the machine and set it upright. Peel the tape off the lid of your washer.

Step 9. Reattach the water supply hoses and the drain hose to the ports at the back of your washer (ensure that these hoses are secured properly so there’s no chance of water leakage).

Step 10. Reconnect your washer to the power outlet and turn the water supply faucet back on. Try running a wash cycle to ensure that everything works properly.

Changing A Worn Belt In Amana Front Loader Washing Machine

Here’s what you’ll need to do to replace a damaged drive belt in your Amana front loader washing machine…

Step 1. In order to prevent electrocution, ensure that your machine is disconnected from the electrical supply before starting this repair.

Step 2. With a 1/4 inch nut-driver, loosen the bolts holding the rear panel to the back of the machine. Lift the panel off the cabinet and set it aside.

Step 3. If still intact, remove the drive belt from the motor pulley drive pulley and discard it.

Step 4. Remove your new washing machine drive belt from its packaging and loop it over the two pulleys.

Step 5. Put your machine’s rear access cover back on and use your nut-driver to apply the bolts. Plug your appliance into the electrical outlet and test it by running a spin cycle.

2. Door Isn’t Locked

As a safety precaution, many washing machines do not start any cycles unless the door is locked. If your washing machine isn’t spinning, check to ensure that the door is properly locked.

If the door of your washer isn’t locking, it indicates that the lock assembly is damaged. Here’s how to replace this part…

See also  Amana Washing Machine Not Filling With Water [How To Fix]

How To Change A Damaged Front Loader Amana Washing Machine Door Lock

Replace a damaged door lock assembly in your Amana washing machine with the following steps…

Step 1. In order to prevent any chances of electrocution, make sure your machine is disconnected from the power outlet before starting this fix.

Step 2. Open your washer’s door. Using either a pair of needle-nosed pliers or a flat-blade screwdriver, take the metal retaining wire off the door boot seal (take care not to damage to the seal).

Step 3. Peel the door seal away from the door lock. Using a Philips screwdriver, loosen the nuts securing the door lock to the cabinet.

Step 4. Reach inside the cabinet and pull the door lock out of place. Unplug the wire connector attached to door lock assembly and set it aside.

Step 5. Remove your new washing machine door lock from its packaging. Plug the wire harness to the new door lock.

Step 6. Install the new door lock in the cabinet and apply the screws with your Philips screwdriver to secure it.

Step 7. Fit the door boot seal around the door opening. Use your screwdriver or needle-nosed pliers to fit the retaining wire back around the door seal. Close your washer’s door.

Step 8. Plug your washing machine back into the power outlet and try running a spin cycle to see if the problem has been fixed.

How To Change A Damaged Top Loader Amana Washing Machine Door Lock

Replace the lid lock in your Amana top loader washing machine with the following steps…

Step 1. In order to prevent water leaks or electrocution, make sure to disconnect your machine from the electrical supply and turn the water valve off before starting this repair.

Step 2. With a pair of pliers, unscrew the two water supply hoses from the ports at the back of your machine (some water will spill out, so ensure that you have a rag nearby to clean any water leaks).

Step 3. Put some tape on the lid of your machine to secure it. Use a 1/4 inch nut-driver to loosen the nuts holding the control panel rear cover. Take the cover off the machine and set it aside.

Step 4. Unplug the wire harness from the terminal on the control board and release the wire from the retainer using a flat-blade screwdriver.

Step 5. Loosen the nuts holding the top panel to the cabinet. Slide the top panel backwards, then lift and support it.

Step 6. With your flat-blade screwdriver, release the lid lock wire from the retainers at the bottom of the top panel.

Step 7. Use a Philips screwdriver to loosen the screws holding the lid lock to the bottom of the top panel. Pull the lid lock and wire off the top panel and discard it.

Step 8. Remove your new washing machine lid lock from its packaging. Mount the new lid lock on the top panel and secure it with the screws.

Step 9. Secure the lid lock wire in the retainers on the top panel. Pass the lid lock connector through the opening on the top panel.

Step 10. Lower the top panel onto the cabinet and snap it into place. Apply the nuts at the back to secure the panel.

Step 11. Plug the lid lock wire connector to the control board. Put the rear access cover back in place and apply the bolts with your nut-driver.

Step 12. Peel the tape off the lid of your machine. Reconnect the water supply hoses to the ports at the back of the washer (in order to prevent water leakage, ensure that the hoses are secured properly).

Step 13. Turn your machine’s water supply back on and plug the power cord back into the outlet. Make sure the issue has been fixed by running a spin cycle.

Check out these other articles…

Amana Washing Machine Noise [Issues & Solutions]

How To Clean Amana Washing Machine [Detailed Guide]

Amana Washing Machine Is Knocking/Banging [How To Fix]

Amana Washing Machine Is Skipping Wash Cycle [Quick Fix]

Amana Washing Machine Won’t Stop… [How To Fix]

Amana Washing Machine Shakes Violently [Proven Solution]

Amana Washing Machine Overflows [How To Fix]

3. Defective Transmission (Top Loaders)

To replace a damaged transmission assembly in your Amana top loader washing machine, here are the steps you’ll need to take…

See also  LG Washing Machine Sound [How To/Issues & Solutions]

Step 1. In order to prevent water leaks or electrocution, make sure your washing machine is disconnected from the power outlet and the water valve is turned off.

Step 2. With a pair of pliers, unscrew the COLD and HOT water supply hoses from the ports at the back of your machine (some water will spill).

Step 3. Put some tape on your machine’s lid to secure it. With a 1/4 inch nut-driver, loosen the nuts at the back of the machine securing the top panel. Lift the top panel and support it using a lanyard or by laying it against a wall.

Step 4. Pry the plastic cap off your washer’s agitator. With a 7/16 inch socket wrench, loosen the nut holding the agitator. Carefully lift the agitator out of the machine and set it aside.

Step 5. Use a flat-blade screwdriver to pry the tub ring off the tub assembly. Using a hammer and a spanner wrench, loosen the tub nut and take it out of the machine. Lift the inner tub out and set it aside.

Step 6. With a hammer, knock the drive block off the drive tube. Lower the top panel onto the cabinet and apply the nuts at the back to secure it.

Step 7. Tilt your washer forwards carefully and set it on the floor. Use your nut-driver to take out the bolts holding the belt guard to the bottom of the machine.

Step 8. Take the drive belt off the motor pulley and transmission pulley. Disconnect the wire harness from the drive motor and release the wire from the retainer.

Step 9. With a socket wrench, loosen the nuts holding the motor assembly to the transmission plate. Carefully lift the motor off the machine and set it aside.

Step 10. Unplug the wire connector from the start capacitor. Use a screwdriver to take out the screw holding the capacitor to the transmission assembly.

Step 11. Disconnect the wire harness attached to the shift actuator next to the transmission pulley. Take out the screw holding the shift actuator to the bottom of the machine.

Step 12. With a 13mm socket, loosen the nut holding the transmission pulley. Take the transmission pulley off and set it aside.

Step 13. Pry the splutch housing off the shaft. Take out the basket drive gear and spring.

Step 14. With your socket wrench, remove the nuts holding the transmission assembly to the bottom of the machine. Carefully pull the transmission assembly out of the tub and set it aside.

Step 15. Remove your new washing machine transmission assembly from its packaging. Slide the shaft of the new transmission through the opening at the bottom of the tub. Apply the mounting bolts with your socket wrench.

Step 16. Put the drive gear and spring onto the shaft of the new transmission. Snap the splutch housing in place.

Step 17. Put the pulley wheel on the shaft and apply the bolt using your socket wrench.

Step 18. Mount the shift actuator on the new transmission plate and secure it with the screws. Plug the wire connector to the actuator.

Step 19. Place the start capacitor on the mounting plate and use your screwdriver to apply the screw. Plug the wire harness to the capacitor.

Step 20. Mount the motor assembly on the transmission plate and apply the bolts with your socket wrench to secure it. Plug the wire harness into the terminal on the motor assembly.

Step 21. Loop the drive belt around the transmission pulley and motor pulley. Put the belt guard over the pulleys and apply the bolts.

Step 22. Lift your machine back onto its feet. Use your nut-driver to take out the bolts securing the top panel. Lift the top panel and support it.

See also  LG Washing Machine Draining [How To/Issues & Solutions]

Step 23. Push the drive block onto the drive shaft. Carefully lower the inner tub onto the shaft. Put the tub nut back in place and use your hammer and spanner wrench to secure it.

Step 24. Place the agitator on the shaft and apply the bolt using your socket wrench. Snap the cap onto the agitator.

Step 25. Snap the tub cover back onto the tub assembly. Lower the top panel and snap it back into the cabinet. Apply the screws at the back with your 1/4 inch nut-driver to secure top panel.

Step 26. Peel the tape off the lid of your machine. Reconnect the water inlet hoses to the ports at the back of your machine.

Step 27. Plug your washer back into the power outlet and turn the water supply valve back on. Try running a spin cycle to ensure that the issue has been fixed.

4. Drive Motor Failure

Replace a failed drive motor in your Amana washing machine with the following steps…

How To Replace Damaged Motor In Top Loader Amana Washing Machine

To change a damaged drive motor in your Amana top loader washing machine, here are the steps you’ll need to take…

Step 1. In order to prevent electrocution and water leakage, ensure that your washer is disconnected from the power outlet and the water valve is turned off before starting this repair.

Step 2. With a pair of pliers, unscrew the HOT and COLD water supply hoses from the ports (water will spill, so ensure that you keep a rag nearby). Put some tape on the lid of your machine to secure it.

Step 3. Tip your washer forwards carefully and lay it on the floor. With a 5/16 inch nut-driver, loosen the bolts holding the belt guard to the bottom of the machine.

Step 4. Take the belt off the motor pulley and transmission pulley. Unplug the wire harness from the terminal on the motor assembly. Release the wire from the retainer.

Step 5. Using a socket wrench, take out the bolts holding the motor assembly to the bottom of the machine. Lift the motor off the mounting plate and set it aside.

Step 6. Remove your new washing machine drive motor from its packaging. Mount the new motor at the bottom of your washer and secure it with the bolts.

Step 7. Plug the wire connector into the new motor and secure the wire in the retainer.

Step 8. Fit the drive belt around the motor pulley and transmission pulley (ensure that the grooved side faces inwards).

Step 9. Place the belt guard over the pulleys and apply the bolts with your socket wrench to secure it.

Step 10. Lift your machine back onto its feet and peel the tape off the lid. Reconnect the water supply hoses to the ports at the back of your machine.

Step 11. Turn your washer’s water supply back on and plug the power cord back into the electrical outlet. Make sure the issue has been fixed by running a spin cycle.

How To Replace A Damaged Motor In Front Loader Amana Washing Machine

Take the following steps to replace a damaged motor in your Amana front loader washing machine…

Step 1. In order to prevent electrocution, make sure to disconnect your washer from the electrical outlet before starting this repair.

Step 2. Use a 1/4 inch nut-driver to take out the nuts holding the rear panel to the cabinet. Lift the panel off the machine and set it aside.

Step 3. Remove the drive belt from the motor pulley and drive pulley. Unplug the wire connectors attached to the motor assembly. Release the wires from the retainer.

Step 4. With a socket wrench, loosen the bolts securing the motor assembly to the bottom of the machine. Carefully lift the motor out of the cabinet and set it aside.

Step 5. Remove your new washing machine drive motor from its packaging. Mount the new motor at the bottom of the tub and secure it with the bolts.

Step 6. Plug the wire connectors to the new motor and secure the wires in the retainer.

Step 7. Loop the drive belt around the drive pulley and the new motor pulley. Put your washer’s rear access panel back on and apply the screws to secure it.

Step 8. Plug your washing machine back into the electrical outlet. To ensure that the problem has been fixed, try running a spin cycle.