Is your Amana washing machine not working? If so, you’ve come to the right place. This detailed guide explains the causes of this issue and provides steps on how to fix them…
Table of Contents
Amana Washing Machine Sensor Not Working — Solved
If your Amana washing machine sensor isn’t working, you’ll need to replace it. Here’s how to do this…
Changing Failed Water Level Sensor In Top Loader Amana Washing Machine
Here are the steps you’ll need to take to replace a failed water level sensor in your Amana top loader washing machine…
Step 1. Disconnect your machine’s power cord from the outlet before starting this repair in order to prevent electrocution.
Step 2. Insert a putty knife underneath the two bottom corners of the control panel (this will release the two retaining clips). Lift the control panel and lay it on top of the machine.
Step 3. Pull the air pressure tube off the water level sensor. Disconnect the wire connector from the sensor.
Step 4. Pry the sensor off the control panel using your flat-blade screwdriver. Take your new washing machine water level sensor out of its packaging.
Step 5. Snap the new sensor onto the control panel. Plug the air pressure hose to the new sensor. Connect the wire harness to the new sensor.
Step 6. Lift the control panel and snap it back into the housing. Plug your machine back into the outlet and try running a rinse cycle to make sure everything works properly.
Changing Failed Water Level Sensor In Front Loader Amana Washing Machine
Change the sensor in your front loader Amana washing machine by doing the following…
Step 1. Unplug your machine from the power cord from the electricity supply before starting this repair.
Step 2. Take out the nuts at the back of the machine securing the top panel using a 1/4 nut-driver. Slide the panel backwards about an inch or so, and lift off the cabinet.
Step 3. Pull the air pressure tube off the water level sensor and unplug the wire connector. Release the sensor from the cabinet using a flat-blade screwdriver.
Step 4. Take the new sensor out of its packaging and snap it into the cabinet. Plug the wire harness to the new sensor. Connect the pressure tube to the port on the sensor.
Step 5. Slide the top panel back onto the cabinet and use your nut-driver to apply the screws at the back. Plug your machine into the electrical outlet and test the machine.
The above steps will solve a case of an Amana washing machine not working that’s due to a bad sensor.
Amana Washing Machin Start Button Not Working — Solutions
Is your Amana washing machine start button not working? If so, look for the following issues…
1. Failed Capacitor (Top Loaders)
Replace a failed Start capacitor in your Amana top loader washing machine by doing the following…
Step 1. Unplug your machine from the electrical supply and turn the water valve off before starting this repair. Put some tape on the lid of your machine to secure it.
Step 2. Release the spring clamp on the drain hose and pull the hose off your machine.
Step 3. Spread a rag underneath the water inlet lines. Use you pliers to unscrew the two inlet hoses from the ports at the back of the machine (some water will spill out).
Step 4. With the help of another person, tilt your machine backwards carefully and lay it on the ground.
Step 5. Unplug the wire harness attached to the start capacitor. Use your screwdriver to take out the screw securing the capacitor to the bottom of the tub. Set the capacitor aside and take the new one out of its packaging.
Step 6. Mount the new capacitor at the bottom of the machine and secure it by applying the screw. Plug the wire connector to the new capacitor.
Step 7. Lift your machine back onto its fee and peel the tape off the lid. Reattach the water supply hoses to the ports on your machine.
Step 8. Reconnect the drain hose to the outlet port and secure it with the spring clamp. Turn the power and water supply back on then try running a wash cycle to see if the problem has been fixed.
2. Unlocked Door
Most washing machines will not start a cycle unless the door is locked. Before starting a cycle, ensure that your machine’s door is firmly shut. If your machine door doesn’t lock, you’ll need to change the lock assembly. Here’s how you can do this…
Replacing Failed Door Lock In Top Loader Amana Washing Machine
Replace your top loader washing machine’s lid lock by doing the following…
Step 1. Turn off the water supply to your washer and disconnect the cord from the power outlet.
Step 2. Unscrew the supply lines from the ports at the back of your machine (water will spill out a bit).
Step 3. Put some tape on the lid of your machine to secure it to the top panel. Use your nut-driver to take out the bolts holding the rear cover of the control panel.
Step 4. Disconnect the wire harness of the lid lock from the terminal on the control board. Release the lid lock wire from the retainer.
Step 5. Take out the bolts holding the top panel to the cabinet. Lift the top panel and support it.
Step 6. Release the lid lock wires from the retainers at the bottom of the control panel using a flat-blade screwdriver.
Step 7. Use your Philips screwdriver to remove the screws holding the lock assembly to the top panel. Pull the lock assembly off the top panel and discard it.
Step 8. Remove your new washing machine lid lock from its packaging. Mount the new lid lock on the top panel and apply the screws to secure it.
Step 9. Use a flat-blade screwdriver to push the lid lock wire into the retainers at the bottom of the control panel. Pass the wire connector through the opening on the control panel.
Step 10. Lower the top panel back onto the cabinet and peel the tape off. Secure the top panel by applying the bolts at the back.
Step 11. Plug the wire harness of the new lid lock into the control board. Put the control panel access cover back on and secure it with the bolts.
Step 12. Reattach the inlet hoses to your machine. Plug the power cord back into the outlet and turn the water supply valve back on. Try running a wash cycle to make sure the problem has been fixed.
Replacing Failed Door Lock In Front Loader Amana Washing Machine
To change a damaged door lock in your front loader Amana washing machine, here are the steps you’ll need to take…
Step 1. Unplug your machine from the power outlet before starting in order to prevent electrocution.
Step 2. Open your machine’s door. With either a flat-blade screwdriver or a pair of needle-nosed pliers, carefully pull out the retaining wire around the door seal.
Step 3. Peel the door seal away from the door lock. Take out the nuts securing the door lock to the cabinet. Reach inside the machine and pull the door lock out of place.
Step 4. Unplug the wire connector from the lock assembly and set it aside. Remove your new lock assembly from the packaging.
Step 5. Plug the electrical connector to the new door lock. Install the new lock in the machine and secure it by applying the screws.
Step 6. Fit the door seal back around the door opening. Secure the door boot seal using the retaining wire. Plug the power cord back into the outlet and try running a wash cycle.
Check out these other articles…
Amana Washing Machine Error Codes [Proven Solutions]
Admiral Washing Machine Lid [Issues & Solutions]
Amana Washing Machine Sensing [Issues & Proven Solutions]
Amana Washing Machine Leaking [How To Fix]
Amana Washing Machine Won’t Agitate [Easy Fix]
3. Faulty Control Board
If none of your machine’s inputs are functioning properly, you may need to replace the control board. Here’s how to do this…
Changing Damaged Control Board In Front Loader Amana Washing Machine
Here are the steps you’ll need to take to replace a control board in an Amana front loader washing machine…
Step 1. In order to prevent electrocution, disconnect your washing machine from its power supply before starting this repair.
Step 2. With a 1/4 inch nut-driver, loosen the bolts at the back of your machine securing the top panel. Slide the panel backwards and lift it off the cabinet.
Step 3. The control board will be mounted at the side of the cabinet. Pry the plastic cover off the control board.
Step 4. Take note of the positioning of each wire harness attached to the board. Disconnect the plugs from the control board.
Step 5. With a flat-blade screwdriver, pry the control board off the side of the cabinet and set it aside.
Step 6. Remove your new washing machine control board from its packaging. Snap the new board into the slots on the cabinet.
Step 7. Plug each wire connector into its corresponding terminal on the new board. Snap the top panel back onto the machine and apply the nuts with your nut-driver.
Step 8. Plug your machine back into the power outlet and try running a wash cycle to make sure everything works properly.
Changing Damaged Control Board In Top Loader Amana Washing Machine
To changed a failed control board in your Amana top loader washing machine, do the following…
Step 1. Make sure your washing machine is disconnected from the power outlet before starting this repair in order to prevent electrocution.
Step 2. Pull the selector knob off the control panel (use some string to make this easier).
Step 3. Insert a tool such as a putty knife under the two corners (this will release the two retaining clips). Set the control panel on top of the cabinet.
Step 4. Pull the air pressure tube off the port on the control board. Unplug each electrical connector from the control board (ensure that you take note of where each connector goes before disconnecting).
Step 5. With a Philips screwdriver, remove the screws holding the board to the control panel. Take the board off the panel and discard it.
Step 6. Remove your new washing machine control board from its packaging. Mount the new board on the panel and use your screwdriver to apply the screws.
Step 7. Lift the control panel and snap the selector knob onto the shaft. Connect the air pressure tube to the new board.
Step 8. Plug each wire harness into the terminals on the new control board. Lift the control panel assembly and snap it back into the cabinet.
Step 9. Connect your washer back to the power supply and try running a wash cycle to make sure the problem has been fixed.
4. Damaged Drive Motor
Replace a failed motor assembly in your washer by taking the following steps…
Amana Top Loader Washer Drive Motor Replacement
Here’s how to replace the motor in your top loader Amana washing machine…
Step 1. Disconnect your machine from the power supply and turn the water valve off before starting this repair.
Step 2. Place some tape over the lid of your washer to secure it. Release the spring clamp holding the outlet hose to the bottom of your machine. Pull the drain hose off the port.
Step 3. Disconnect the COLD and HOT water supply lines from the inlet ports at the back of your washing machine (spread a rag on the floor under the hoses to catch any water leaks).
Step 4. With the assistance of another person, tilt the washer backwards carefully and lay it on the floor.
Step 5. Take out the nuts holding the belt guard using a nut-driver. Set the belt guard aside and carefully take the drive belt off the two pulleys.
Step 6. Disconnect the plug from the motor assembly and use a flat-blade screwdriver to release the wire from the retainer.
Step 7. Use a socket wrench to remove the mounting bolts holding the motor assembly to the transmission plate. Take the the motor off and set it aside.
Step 8. Remove your new motor assembly from its packaging and mount it at the bottom of the machine. Secure the new motor by applying the bolts.
Step 9. Plug the wire connector to the new motor and secure the wire in the retainer. Carefully loop the drive belt around the motor pulley and drive pulley (ensure that the grooved side faces inwards).
Step 10. Put the belt guard back in place and apply the nuts to secure it. Carefully set your washer on its feet and peel the tape off the lid.
Step 11. Connect the two water supply lines to the ports on your machine (in order to prevent water leaks, make sure to secure the hoses properly).
Step 12. Reattach the drain hose to the machine and secure it with the spring clamp. Turn your washer’s water and power supply back on then test the machine by running a wash cycle.
Amana Front Loader Washer Drive Motor Replacement
Replace the motor assembly in your front loader washing machine by taking the following steps…
Step 1. Turn off your washer’s power supply before starting this repair in order to prevent electrocution.
Step 2. Take out the bolts holding the rear access panel using a 1/4 inch nut-driver. Lift the rear panel off the washer and set aside.
Step 3. Take the drive belt off the drive pulley and motor pulley. Unplug the wire connector from the terminal on the motor assembly.
Step 4. Using a socket wrench, loosen the nuts securing the motor assembly to the mounts at the bottom of the tub. Carefully pull the motor out of place and discard it.
Step 5. Remove your new motor assembly from its packaging and mount it at the bottom of the tub. Secure the new motor by applying the mounting bolts.
Step 6. Plug the wire connector to the new motor. With the grooved side facing inwards, loop the drive belt around the motor pulley and drive pulley.
Step 7. Put the rear panel back onto the cabinet and apply the bolts. Reconnect your washer to its power outlet and try running a wash cycle.
Amana Washing Machine Not Working — Conclusion
This should fix your “Amana washing machine not working” issue in most cases. However, if the problem persists after you’ve done all the steps correctly, please, contact a certified appliance technician.
