Bosch Washing Machine Error Codes [Meanings & Solutions]

This detailed guide gives you steps on how to handle Bosch washing machine error codes…

Bosch Washing Machine Error Code E17 — How To Fix

The E17 Bosch washing machine error code indicates that the machine is taking too long to fill. If your washing machine isn’t filling with water, here are the issues to look for…

1. Water Supply Is Off

The first obvious thing you should check is the water supply. Your washing machine will not be able to fill with water if the supply faucet is turned off.

2. Inlet Filters Are Clogged

Clean clogged inlet filters in your Bosch washing machine with the following steps…

Step 1. Prevent electrical damaged and water leaks by disconnecting your washer from the outlet and shutting the water supply valve before starting this repair.

Step 2. With a pair of pliers unscrew the COLD and HOT water supply hoses from the ports at the back of your washer (some water may spill out, so we recommend keeping a rag nearby to clean any leaks).

Step 3. Use a pair of needle-nosed pliers to pull out the little mesh filters inside each of the inlet ports.

Step 4. Take both filters to a sink and use a soft brush to clean out any dirt that may have clogged them. Once both filters are clean, push them back into the ports.

Step 5. Reconnect the two water supply lines to the back of your washing machine (in order to prevent leakage, ensure that the hoses are secure properly).

Step 6. Plug your washing machine back into the electrical outlet and turn the water supply faucet back on. To ensure that the problem has been fixed, try running a wash cycle.

3. Water Inlet Valve Is Damaged

Here are the steps you’ll need to take to replace the water inlet valve in your Bosch washing machine…

Step 1. Prevent electrocution and water leakage by shutting your washer’s water supply faucet and unplugging the power cord from the outlet.

Step 2. Spread a rag on the floor underneath the two water supply hoses to catch any water leaks. Using a pair of pliers, unscrew the two inlet hoses from the ports at the back of the cabinet.

Step 3. With a Torx screwdriver, remove the bolts at the back of the washing machine securing the top panel. Pull the panel backwards about an inch or so, then lift it off the washing machine.

Step 4. The water inlet valve will be mounted inside the cabinet. Disconnect the wire connectors attached to the inlet valve assembly.

Step 5. Using a pair of pliers, press the spring clamps on the tubes connected to the inlet valve, then slide them out of place. Pull each tube off the inlet valve (water will spill out).

Step 6. With a flat-blade screwdriver, pry the inlet valve assembly off the tabs on the cabinet and discard the valve.

Step 7. Prepare your new washing machine water inlet valve for installation by removing it from its packaging.

Step 8. Snap the new inlet valve into the slot at the back of the cabinet. Plug the wire connectors into the appropriate terminals on the new inlet valve assembly.

Step 9. Connect each tube to its corresponding port on the new inlet valve and secure them by sliding the spring clips into place.

Step 10. Place the top panel back on the cabinet and apply the bolts at the back with your Torx screwdriver.

Step 11. Reconnect both water supply hoses to the ports at the back of the washer. Turn your machine’s water supply faucet back on, then plug the power cord back into the outlet. Ensure that the problem has been fixed by running a wash cycle.

Bosch Washing Machine Error Code F18 — Solved

The F18 Bosch washing machine error code indicates that there is an issue with the drainage system. If your washer isn’t draining properly, here are the things you should do…

1. Clean The Pump Filter

Clean the pump filter in your Bosch washing machine with the following steps…

Step 1. In order to prevent any electrical damage, make sure your washing machine is unplugged from the outlet before starting this repair.

Step 2. Place a rag on the floor in front of your washer. Pry open the little access panel at the bottom of the front panel.

Step 3. Pull out the short capped hose under the panel. Place a container under the hose.

Step 4. Pull the hose’s cap off and let any water that the may be stuck in washer drain out. Once all the water has drained out completely, put the hose’s cap back on and push it back into the retainers.

Step 5. Turn the knob next to the emergency drain hose counter-clockwise and take it out of the machine.

Step 6. Take the filter to a sink and clean out any debris and lint that may have accumulated in it. Clean the filter housing with a cloth.

Step 7. Push the filter back into the housing and turn it clockwise to lock it. Snap the lower access panel back onto the machine.

Step 8. Plug your washing machine back into the electrical outlet and try running a wash cycle to see if the problem has been fixed.

2. Replace The Drain Pump

To replace the drain pump in your Bosch washing machine, here are the steps you’ll need to take…

Step 1. Unplug your washing machine from the power outlet before starting this repair in order to prevent electrocution. Drain out any water stuck in the tub using the emergency drain pump.

Step 2. Using a screwdriver, take out the bolts at the back of the machine securing the top panel. Lift the panel off the machine and set it aside.

Step 3. Take out the bolts securing the rear access panel. Lift the cover off the cabinet, then set it aside.

Step 4. Push some cardboard into the space between the drum and the cabinet wall (this will help wedge the drum).

Step 5. Tip the washing machine sideways carefully and set it on the floor (if the machine is too heavy, get someone to help you).

Step 6. Disconnect wire harness from the terminal on the drain pump (the pump will be at the bottom of the cabinet). Turn the drain pump counter-clockwise and pull it off the port (some water will spill out, so ensure that you have a rag nearby).

Step 7. Remove your new washing machine drain pump from its packaging. Push the new pump assembly firmly into the port and turn it clockwise to lock it in place.

Step 8. Plug the wire connector into the new drain pump assembly. Carefully lift your washing machine onto its feet and take the cardboard out of the cabinet.

Step 9. Put the rear access panel back onto the machine and apply the bolts using your screwdriver.

Step 10. Place the top panel on the cabinet and use your screwdriver to secure the bolts at the back. Plug your washing machine back into the electrical outlet, then try running a wash cycle to see if the problem has been fixed.

Bosch Washing Machine Error Code F21 — Quick Fix

The F21 Bosch washing machine error code indicates that the motor has failed. To replace a failed motor, here are the steps you should take…

Step 1. In order to prevent any chances of electrocution or water spillage, unplug your washing machine from the electrical outlet and turn the water supply faucet off.

Step 2. Using your pliers, unscrew the two water supply hoses from the back of your machine (some water may spill out).

Step 3. With a Torx screwdriver, remove the bolts holding the top panel to the cabinet. Lift the top panel off the machine and set it aside.

See also  Washing Machine Valve [How To, Problems & Solutions]

Step 4. Remove the bolts at the back of the machine securing the rear access panel. Take the drive belt off the two pulley wheels (take care not to cut yourself on the rear panel).

Step 5. Wedge some cardboard or some towels into the space between the drum and the right side of the cabinet.

Step 6. Tip your washing machine on its side carefully and set it on the floor (if needed get someone to help you).

Step 7. Using a socket wrench, remove the bolts holding the motor assembly to the bottom of the tub. Unplug the wire connector attached to the motor.

Step 8. With a flat-blade screwdriver, pry the motor assembly off the mounts (be sure to support the motor with your hand).

Step 9. Discard the old motor and take the new one out of its packaging. Mount the new motor assembly at the bottom of the washing machine and apply the bolts using your socket wrench.

Step 10. Plug the wire connector to the terminal on the new motor assembly. Carefully set your washing machine back onto its feet.

Step 11. Remove the support from the side of the the cabinet. Loop the drive belt around the drive pulley and motor pulley.

Step 12. Place the rear access panel on the cabinet and apply the bolts with your screwdriver.

Step 13. Reattach the COLD and HOT water supply lines to the washer. Put your machine’s top panel back on and secure the nuts at the back with your Torx screwdriver.

Step 14. Turn your washer’s water supply faucet back on, and plug the power cord back into the outlet. Try running a cycle to see if the problem has been fixed.

Check out these other articles…

Amana Washing Machine Smells [How To Fix]

Amana Washing Machine Won’t Lock [How To Fix]

How To Clean Bosch Washing Machine [Detailed Guide]

Washing Machine Rotating In One Direction [How To Fix]

Bosch Washing Machine Leaking [How To Fix]

How To Reset Bosch Washing Machine [Detailed Guide]

Washing Machine Unbalanced [Proven Solutions]

Bosch Washing Machine Error Code F26 — Quick Fix

The F26 Bosch washing machine error code indicates that the water pressure switch is damaged. To replace this part, here are the steps you’ll need to take…

Step 1. Make sure your washing machine is unplugged from the electrical outlet before starting this repair in order to prevent electrocution.

Step 2. Using a Torx screwdriver, take out the bolts securing the top panel to the cabinet. Pull the top backwards about an inch or so, then lift it off the machine.

Step 3. Unplug the wire connector from the water pressure switch mounted at the side of the cabinet. Use your screwdriver to take out the bolt holding the pressure switch.

Step 4. Release the spring clamp on the tub connected to the pressure switch, then slide it out of place. Pull the pressure tube off the switch.

Step 5. Discard the old pressure switch and remove the new one from its packaging. Attach the air pressure tube to the port on the new switch and secure it using the spring clip.

Step 6. Mount the switch on the cabinet and apply the screw to secure it. Connect the wire harness to the terminal on the new switch.

Step 7. Place the top panel on the cabinet and apply the screws at the back using your Torx screwdriver.

Step 8. Reconnect your washing machine to its electrical outlet and try running a cycle to ensure that the problem has been fixed.

Bosch Washing Machine Error Code F43 — Solved

The F43 Bosch washing machine error code indicates that the something is preventing the drum from turning. Here are the things that could cause this issue…

1. Drive Belt Is Damaged

To change a damaged drive belt in your Bosch washing machine, take the following steps…

Step 1. Ensure that your washer is unplugged from the electrical outlet in order to prevent electrocution.

Step 2. Using a screwdriver, remove the bolts securing the rear access panel. Lift the panel off the machine and set it aside.

Step 3. If still intact, take the drive belt off the two pulley wheels (take care not to cut yourself on the edge of the cabinet).

Step 4. Take your new drive belt out of its packaging. With the grooved side turned inwards, loop the new belt around the drive pulley and motor pulley).

Step 5. Once the belt is in place, put the rear access panel back on and apply the bolts to secure it.

Step 6. Plug your washer back into the power outlet, then ensure that the problem has been fixed by running a wash cycle.

2. Bearings Have Gone Bad

The bearings in your washer help ensure that the drum spins smoothly during wash cycles. If the bearings have gone bad, here are the steps you’ll need to take to replace them…

Step 1. Prevent any chances of electrocution by ensuring that the washer is disconnected from the power outlet before starting this repair.

Step 2. With a Torx screwdriver, take out the nuts at the back of the machine holding the top panel. Lift the top off the cabinet and set it aside.

Step 3. Pull the detergent drawer out and press the tab to release it from the housing completely.

Step 4. Use your Torx screwdriver to remove all the bolts securing the control panel to the front of the cabinet.

Step 5. Take note of the positioning of each wire connector attached to the control board, then unplug each one. Set the control panel aside.

Step 6. Pry the lower front access panel off the machine and set it aside. Use your screwdriver to take out the bolts at the top and bottom of the main front panel.

Step 7. Open your washing machine’s door. Using either a pair of needle-nosed pliers or a flat-blade screwdriver, take the retaining wire off the door boot seal (take care not to damage the seal).

Step 8. Peel the door seal off the opening. Use your screwdriver to loosen the bolts holding the door lock assembly to the cabinet.

Step 9. Carefully lift the front panel off the machine and set it aside. Take out the cross-member under the detergent dispenser.

Step 10. Push the detergent dispenser out of place. Using a pair of pliers, squeeze the clamp on the hose connecting the dispenser to the tub and slide it out of place. Pull the hose off the tub. Set the dispenser aside.

Step 11. Using your Torx screwdriver, take out the nuts holding the front counter-weight to the machine. Lift the weight off the tub carefully and set it aside.

Step 12. Loosen the bolts securing the top counter-weight using a 13mm socket wrench. Take the weight off the tub and set it aside.

Step 13. Unplug the wire connectors attached to the heating element at the bottom off the tub (ensure that you take note of where each connector goes).

Step 14. Using a nut-driver, loosen the heating element nut until it is leveled with the shaft. Using a screwdriver and a hammer, strike the shaft on the heating element (this will release the lock).

Step 15. Slide the heating element out of the housing and set it aside. Use a screwdriver to release the screw-clamp holding the outlet hose to the tub.

Step 16. Place a rag and a container on the floor of the cabinet to clean up any water leaks. Pull the hose off the port.

Step 17. Use your screwdriver to loosen the screws holding the wire retainers to the tub.

Step 18. Go to the back of your washing machine. Using your Torx screwdriver, take out the bolts securing the rear access panel. Lift the panel off the machine and set it aside.

Step 19. Carefully take the drive belt off the motor pulley and drive pulley. Unplug the wire connector attached to the motor assembly at the bottom of the tub.

Step 20. Use your nut-driver, remove the bolts holding the motor to the bottom of the machine. Carefully pull the motor assembly out of place, then set it aside.

Step 21. Release the clip holding the pressure chamber to the tub using a pair of needle-nosed pliers.

Step 22. Using your socket wrench, loosen the upper mounting bolts securing the shock absorbers to the tub. Pull each shock absorber out of its mount.

See also  Candy Washing Machine Draining [How To, Issues & Solutions]

Step 23. Carefully lift each of the two suspension springs and unhook them from the cabinet.

Step 24. Carefully pull the tub assembly out of the cabinet. Using a flat-blade screwdriver, carefully pry the inner retaining clip off the door boot seal. Peel the door seal off the drum opening carefully.

Step 25. Set the drum assembly on two wooden supports face-down. Use a 13mm socket wrench to take out the nut holding the drive pulley to the back of the drum. Lift the pulley wheel off and set it aside.

Step 26. With your Torx screwdriver, remove the bolts holding the two halves of the tub together. Pull the two halves of the tub apart, then set the front half aside.

Step 27. Pull the inner tub out of the rear half of the outer tub. Set the lower half of the outer tub on two wooden supports facing upwards.

Step 28. Using a mallet and chisel, carefully knock out the smaller outer bearing. Turn the tub over and set it on the supports. Knock the inner bearing and bearing seal out of the tub using your chisel and mallet.

Step 29. Take the old bearing pieces out of the tub, then discard them. Clean out any dirt that may have accumulated in the tub.

Step 30. Take your new bearing kit out of its packaging. Using a mallet and a small block of wood, carefully knock the inner bearing into the seat.

Step 31. Knock the new bearing seal into place right above the inner bearing using a mallet. Turn the tub assembly over and set it on the supports.

Step 32. Use your mallet and wooden block to knock the outer bearing into the seat (ensure that the housing is cleaned thoroughly).

Step 33. Lift the outer tub and turn it upwards. Guide the inner tub into the rear half of the outer tub. Turn the assembly over and put the drive pulley back onto the shaft. Apply the bolt using your socket wrench to secure the pulley.

Step 34. Turn the tub assembly over again. You will find a small rubber seal in the groove of the rear half of the outer tub. It is advised that you replace this seal whenever you split the drum in two, in order to prevent water leakage.

Step 35. Put the front half of the outer tub onto the tub assembly and apply all the nuts using your Torx screwdriver. Carefully fit the door boot seal and inner retaining band around the drum opening.

Step 36. Carefully guide the tub assembly back into the cabinet and hook the two suspension springs into the holes.

Step 37. Push the two shock absorbers into the mounts at the bottom of the tub assembly and apply the bolts with your socket wrench.

Step 38. Put the top and front counter-weights back onto the tub assembly and apply the bolts and screws to secure them.

Step 39. Reattach the detergent dispenser hose to the port at the top of the tub. Secure the hose with the spring clamp.

Step 40. Mount the drive motor onto the bottom of the tub assembly and apply the bolts using your socket wrench. Plug the wire connector back into the motor.

Step 41. Carefully loop the drive belt around the motor pulley and drive pulley. Place the rear access panel back onto the machine and apply the nuts using your Torx screwdriver.

Step 42. Snap the air pressure dome back onto the retainer. Push the heating element back into the housing and apply the bolt to secure it. Plug each wire connector into its appropriate port on the element.

Step 43. Reattach the outlet hose to the port at the bottom of the tub assembly. Tighten the screw clamp using your screwdriver.

Step 44. Put the cross-member and detergent dispenser back in place. Mount the front panel onto the cabinet and apply the screws at the top and bottom using your screwdriver.

Step 45. Snap the lower front access panel back onto the cabinet. Open the door of your washing machine and push the door lock back into place. Secure the door lock by applying the screws.

Step 46. Carefully fit the door boot seal back around the door opening. Using your flat-blade screwdriver or needle-nosed pliers, fit the outer retaining band around the door boot seal.

Step 47. Plug each wire connector into its appropriate terminal on the control board. Snap the control board onto the cabinet and apply all the screws with your Torx screwdriver.

Step 48. Slide the detergent drawer back into the housing. Place the top panel on the cabinet and apply the screws at the back to secure it.

Step 49. Turn your washer’s water supply faucet back on and plug the power cord back into the electrical outlet. To ensure that the problem has been fixed, try running a spin cycle.

Bosch Washing Machine Error Code F63 — How To Fix

The F63 Bosch washing machine error code indicates that the control board has failed. Before you rush to replace the board, disconnect your washer from the outlet for about 10 minutes then plug it back in (this will clear any system glitches.

If the problem still isn’t fixed, you’ll need to replace the control board. Here’s how to do this…

Step 1. In order to prevent electrical damage, make sure your washing machine is disconnected from the power outlet before starting this repair.

Step 2. With your Torx screwdriver, loosen the bolts at the back of the machine securing the top panel. Lift the top off the washing machine and set it aside.

Step 3. Pull the detergent drawer out of and press the tab inside to completely release it from the housing.

Step 4. Use your Torx screwdriver to take out all the screws holding the control panel to the cabinet. Carefully pry the panel off the cabinet (use a flat-blade screwdriver if needed).

Step 5. Unplug each wire connector attached to the control board (ensure that you note where each connector goes).

Step 6. Use your screwdriver to remove the bolts holding the control board to the panel. Take the board off the panel, then discard it.

Step 7. Prepare your new washing machine control board for installation by removing it from its packaging.

Step 8. Mount the new board on the panel and apply the screws using your screwdriver. Plug each wire harness into its corresponding terminal on the new control board.

Step 9. Snap the control panel onto the front of the cabinet and apply all the screws using your Torx screwdriver.

Step 10. Slide the detergent drawer back into the housing. Place the top panel on the cabinet and use your Torx screwdriver to apply the nuts a the back. Plug the power cord into the outlet and try running a wash cycle to ensure that the problem has been fixed.

Bosch Washing Machine Error Code E35 — Solution

The E35 Bosch washing machine error code indicates that there is a water leak in your machine. Here are the thing that could cause this issue…

1. Door Boot Seal Is Damaged

If your washer’s door boot seal is punctured, water will begin to leak out during wash cycles. Here are the steps you’ll need to take to replace this part…

Step 1. Prevent any chances of electrocution by ensuring that your washing machine is disconnected from the electrical outlet before starting this repair.

Step 2. Go to the back of the machine and loosen the bolts securing the top panel using a Torx screwdriver. Lift the panel off the cabinet, then set it aside.

Step 3. Pull the soap drawer out and press the tab inside to release it from the housing completely.

Step 4. With your Torx screwdriver, loosen all the bolts securing the control panel to the front of the cabinet. Use a flat-blade screwdriver to help pry the panel off.

Step 5. Take note of the positioning of the wire harnesses attached to the control board, then disconnect each one.

Step 6. Set the control panel aside and pry the lower front access panel off the cabinet.

Step 7. Open your washer’s door. With your screwdriver, remove the nuts securing the door lock to the cabinet.

Step 8. Using a flat-blade screwdriver, carefully pry the retaining band off the door boot seal. Peel the seal off the door opening.

See also  Washing Machine Not Working [How To Fix]

Step 9. Use your screwdriver to take out the bolts at the top and bottom of the front panel. Carefully lift the panel off the cabinet, then set it aside.

Step 10. Use a flat-blade screwdriver to carefully pry the out the inner retaining band holding boot seal to the drum. Peel the door boot seal away from the tub assembly and discard it.

Step 11. Take your new washing machine door boot seal out of its packaging. Fit the new boot seal carefully around the drum opening. Fit the inner retaining band around the new seal (use a flat-blade screwdriver if needed).

Step 12. Mount the front panel back onto the cabinet and use your Torx screwdriver to apply all the bolts.

Step 13. Snap the lower front access panel back onto the machine. Push the door lock back into place and apply the screws to secure it.

Step 14. Carefully fit the new door boot seal around the door opening. Secure the new seal by fitting the metal retaining wire around it (take care not to puncture the seal).

Step 15. Plug the wire connectors into the appropriate terminals on the control board. Snap the control panel onto the cabinet and apply all the bolts using your Torx screwdriver.

Step 16. Push the detergent drawer back into the housing. Place the top panel on the washer and apply the nuts at the back to secure it. Plug your machine into the electrical outlet and test the washer by running a cycle.

2. Bearing Seal Is Damaged

The bearing seal mounted at the back of the tub prevents water from leaking through the bearings. To replace this part, take the following steps…

Step 1. Prevent electrocution by ensuring that your washing machine is disconnected from the power outlet before starting this repair.

Step 2. Use your screwdriver to loosen the bolts at the back of the machine securing the rear access panel. Pry the cover off the machine and set it aside.

Step 3. Carefully take the drive belt off the motor pulley and drive pulley, then set it aside.

Step 4. Loosen the bolts holding the top panel to the cabinet. Lift the cover off the machine and set it aside.

Step 5. Pull the detergent drawer out and press the tab inside to release it from the housing completely.

Step 6. With your Torx screwdriver, take out the bolts holding the front panel to the cabinet. Pry the control panel off the front of the machine (if needed, use a pair of pliers).

Step 7. Note the positioning of the wire harnesses connected to the control panel, then unplug each one. Set the control panel aside.

Step 8. Pry the lower front access panel off the machine and set it aside. Open your washing machine’s door and use a Torx screwdriver to take out the bolts holding the door lock to the cabinet.

Step 9. Using either a flat-blade screwdriver or a pair of needle-nosed pliers, carefully take the metal retaining band off the door boot seal.

Step 10. Peel the door gasket off the door opening. With a Torx screwdriver, remove the bolts at the top and bottom of the front panel. Carefully lift the entire front panel off the cabinet, then set it aside.

Step 11. Push the cross-member and detergent dispenser out of place. With a pair of pliers, squeeze the clamp on the dispenser hose connected to the top of the tub assembly. Pull the hose off the tub.

Step 12. Set the detergent dispenser aside. Using your Torx screwdriver and a 13mm socket wrench, loosen the bolts holding the counter-weights to the front and top of the tub assembly. Carefully lift each weight off.

Step 13. Unplug each electrical connector attached to the heating element at the bottom of the tub (ensure that you take note of the positioning of each connector).

Step 14. Use your nut-driver to loosen the heater until it is lined up with the shaft. Use a screwdriver and a hammer to knock the shaft (this will release the heating element).

Step 15. Slide the heating element out of the housing and set it aside. Using a pair of wire cutters, cut the zip-ties holding the wires to the side of the tub.

Step 16. With your screwdriver, loosen the screw-clamp securing the sump hose to the bottom of the tub. Pull the hose off the tub (spread a towel on the floor of the cabinet to catch any water leaks).

Step 17. Disconnect the wire harness connected to the motor assembly at the bottom of the tub. Cut the zip-tie holding the wires to the motor.

Step 18. Using a nut-driver, loosen the bolts securing the motor assembly to the bottom of the outer tub. Carefully pull the motor out of the cabinet and set it aside.

Step 19. Release the air pressure dome from the retainer at the side of the tub using a pair of needle-nosed pliers.

Step 20. With your socket wrench, take out the upper mounting bolts securing the shock absorbers to the bottom of the outer tub. Pull each shock out of the mounts.

Step 21. Lift each of the two suspension springs and lower the tub assembly to the bottom of the cabinet. Carefully guide the tub assembly through the front of the cabinet.

Step 22. Using a flat-blade screwdriver, carefully pry the inner retaining band off the door boot seal. Peel the seal off the tub opening.

Step 23. Turn the tub assembly over and set it on two wooden supports. Use your socket wrench to loosen the nut securing the drive pulley to the bottom of the tub assembly.

Step 24. With your Torx screwdriver, loosen all the bolts securing the two halves of the tub together. Carefully pry the front half of the outer tub off the tub assembly, then set it aside.

Step 25. Lift the inner tub assembly out of the rear half of the outer tub. Using a chisel or a flat-blade screwdriver, pry the bearing seal out of the tub.

Step 26. Take your new washing machine bearing seal out of its packaging. Push the new seal into the tub firmly.

Step 27. Lower the inner tub into the rear half of the outer tub. Turn the tub assembly face-down, and set it on the two supports.

Step 28. Place the drive pulley on the shaft and apply the bolt using your socket wrench.

Step 29. Turn the tub assembly upwards and lower the front half of the outer drum on in. Secure both halves of the tub by applying the bolts with your Torx screwdriver. Fit the door boot seal and inner retaining band around the drum.

Step 30. Guide the tub assembly back into the machine and hook the two suspension springs to the cabinet.

Step 31. Push the two shock absorbers into the mounts at the bottom of the tub assembly and apply the bolts to secure them.

Step 32. Go to the back of the washer and mount the motor assembly onto the bottom of the tub. Apply the bolts using your socket wrench. Plug the wire harness into the motor.

Step 33. Loop the drive belt around the drive pulley and motor pulley. Place the rear access panel on the cabinet and apply the screws using your Torx screwdriver.

Step 34. Push the heating element back into the housing at the bottom of the tub, and apply the bolt using your socket wrench. Plug each wire connector into its appropriate terminal on the heater. Secure the wires to the tub using a zip-tie.

Step 35. Snap the air pressure dome back into the retainer. Connect the sump hose to the port at the bottom of the tub assembly and tighten the screw clamp.

Step 36. Place the counter-weights back onto the front and top of the tub assembly. Apply the bolts using your socket wrench and a screwdriver.

Step 37. Connect the dispenser hose back to the port at the top of the tub assembly and slide the spring clamp into place to secure the connection.

Step 38. Put the cross member and detergent dispenser back in place. Mount the front panel onto the cabinet and apply all the screws to secure it.

Step 39. Snap the lower front access panel onto the cabinet. Open your washer’s door.

Step 40. Push the door lock back into place and apply the nuts using your Torx screwdriver. Fit the door boot seal around the door opening. Use the needle-nosed pliers to fit the outer retaining band.

Step 41. Reconnect each wire connector to its appropriate terminal on the control board. Snap the control panel onto the front of the cabinet and apply all the screws with your Torx screwdriver.

Step 42. Slide the soap drawer back into the housing. Place the top panel on the machine and apply the bolts at the back to secure it.

Step 43. Plug your washing machine back into the electrical outlet and try running a rinse cycle to ensure that the leak is gone.