If your GE washing says different things on the display and you don’t know what to do, you’ve come to the right place. This guide will explain the meaning of these messages and show you fix them. So, without wasting any more time, let’s get right to it..
Table of Contents
GE Washing Machine Says H2o — Solution
If your GE washing machine says H2o on the display, it means something is preventing the appliance from filling. Here are the things that could cause this issue…
1. Water Supply Isn’t Turned On
Always ensure that your washing machine’s water supply is fully opened before starting any wash cycles. If the supply line is closed, your washer won’t be able to start the cycle.
2. Water Inlet Filters Are Blocked
Do the following to clear the water inlet filters in your GE washing machine…
Step 1. Always ensure that you turn off your washing machine’s water and power supply before attempting any repairs in order to avoid electrocution and water leakage.
Step 2. Disconnect the water inlet hoses from the inlet ports at the back of your washing machine (make sure to keep a rag nearby in case water leaks out).
Step 3. Use a pair of pliers to pull out the little mesh filter in each of the ports at the back of your washing machine.
Step 4. Take the filters to a sink and rinse out any dirt that may be clogging them. Push the filters back into the ports once you’ve cleaned them properly.
Step 5. Connect the water inlet hoses back to the inlet ports at the back of your washing machine and make sure the connections are secure to avoid water leakage.
Step 6. Turn on your washing machine’s water and power supply then run a wash cycle to see if the issue has been resolved.
3. Water Inlet Valve Is Damaged
Here’s how to replace a damaged water inlet valve in your GE washing machine…
Replacing GE Top Loader Washing Machine Water Inlet Valve
To replace a damaged water inlet valve in your GE top loader washing machine, here’s what you’ll need to do…
Step 1. Make sure to turn off your washing machine’s water and power supply before attempting any repairs in order to avoid electrocution and water leakage.
Step 2. Disconnect the water inlet hoses from the inlet ports at the back of your washing machine (make sure to have a rag nearby in case water spills out of the hoses).
Step 3. Remove the screws at the back of the washing machine holding the control panel with a Philips screwdriver.
Step 4. Slide the control panel sideways and detach it from your washing machine.
Step 5. The water inlet valve will be mounted on the control panel bracket. Disconnect the solenoid wire connectors from the water inlet valve assembly.
Step 6. Use a pair of pliers to press the clamp on the hose connected to the water inlet valve and slide the hose out of place.
Step 7. Use your screwdriver to take out the mounting screws holding the water inlet valve assembly to your washing machine.
Step 8. Pull the water inlet valve assembly out of your washing machine and set it aside.
Step 9. Get your new washing machine water inlet valve out of its packaging.
Step 10. Install the new water inlet valve assembly in your washing machine and apply the three mounting screws to secure it.
Step 11. Connect the hose to the new water inlet valve assembly and slide the retaining clamp in place to secure it.
Step 12. Connect the each solenoid wire connector to its appropriate terminal on the new water inlet valve assembly.
Step 13. Put the control panel back on and secure it by applying the screws at the back of the washing machine.
Step 14. Connect the water inlet hoses to the inlet ports at the back of your washing machine.
Step 15. Plug your washing machine back to its power outlet and turn on the water supply. Afterwards, make sure everything is working properly by running a wash cycle.
Note: Click here to learn more about your washing machine’s water inlet valve.
Check out these other articles…
GE Washing Machine Door [Issues & Solutions]
GE Washing Machine Sounds Like… [How To Fix]
GE Washing Machine Not Working [Quick Fix]
How To Install GE Washing Machine… [Detailed Guide]
GE Washing Machine Turning On/Off [Issues Solved]
How To Replace GE Front Loader Washing Machine Water Inlet Valve
To replace a faulty water inlet valve in your GE front loader washing machine, here are the steps you’ll need to take…
Step 1. Turn off your washing machine’s water and power supply before attempting any repairs in order to avoid electrocution or water leakage.
Step 2. Go to the back of your washing machine and disconnect the water inlet hoses from the inlet ports (make sure to keep a rag nearby in case some water spills out of the hoses).
Step 3. Use a Philips screwdriver to take out the screws at the back of your washing machine holding the top panel.
Step 4. Slide the top panel back a few inches and lift it off your washing machine.
Step 5. Disconnect the solenoid wire connectors attached to the water inlet valve assembly inside the washing machine’s cabinet (make sure to take note of where each wire is positioned).
Step 6. Use a pair of pliers to press the clamp holding the hose to the water inlet valve assembly and slide the clamp out of place.
Step 7. Disconnect the hose from the water inlet valve assembly.
Step 8. Use your Philips screwdriver to take out the two mounting screws at the back of your washing machine next to the water inlet ports holding the water inlet valve.
Step 9. Pull the water inlet valve assembly out of the washing machine assembly and set it aside.
Step 10. Take your new water inlet valve assembly out of its packaging.
Step 11. Install the new water inlet valve assembly in your washing machine and secure it by applying the two Philips screws at the back of the washing machine.
Step 12. Connect the hose to the new water inlet valve assembly then press and secure it by sliding the retaining clamp in place.
Step 13. Connect each solenoid wire connector to its appropriate terminal on the new water inlet valve assembly.
Step 14. Connect the water inlet hoses to their appropriate ports on the new water inlet valve assembly (In order to prevent water leakage, make sure you tighten the connections).
Step 15. Slide the top panel of your washing machine back on and apply the Philips screws at the back to secure it.
Step 16. Turn on your washing machine’s water supply and plug the power cord back in, then ensure that everything is working properly by trying a wash cycle.
GE Washing Machine Says Balancing — How To Fix
If your GE washing machine says ‘balancing’ on the display, it means that the load in the tub is unbalanced. Here’s how to fix an unbalanced load in your GE washing machine…
Step 1. Turn off your washing machine’s power supply.
Step 2. Open the door of your washing machine and inspect the quantity of clothes in the drum. Ensure that the drum has not been filled past 3/4. If the drum is overloaded, your washing machine won’t be able to spin properly.
Step 3. Make sure your washing machine is sitting on a firm, even surface. If your washing machine is tilted at an angle, the weight of the clothes won’t be distributed evenly.
Step 4. Turn on your washing machine’s power supply and try running the spin cycle again to see if the issue has been resolved.
