If you want to learn how to clean Amana washing machines, you’ve come to the right place. This easy-to-follow guide gives you step-by-step instructions on how to do this.
So, without further ado, let’s get right to it…
Table of Contents
How To Clean Amana Washing Machine — Solved
This is how to clean Amana washing machines…
Step 1. Remove all clothes from your washer’s drum.
Step 2. Pour about 2 cups of vinegar into your machine (vinegar helps get rid of foul smells and mould).
Step 3. Turn your washing machine on and set it to a wash cycle on the hottest water temperature. Press the start button to begin the cycle.
Step 4. Once the wash cycle has been completed, use a clean towel to wipe the interior of your machine.
Step 5. Using some cleaning wipes, clean the exterior of the machine. Leave your washing machine’s lid/door for a few hours (this will help the drum air out).
How To Clean Amana Washing Machine With Affresh — Solved
To clean your Amana washing machine with Affresh, take the following steps…
Step 1. Remove all clothing items from your machine.
Step 2. Put about 2 Affresh tablets into your washing machine.
Step 3. Set the washer to a normal wash cycle and press Start to begin. Once the cycle has ended, leave the machine’s door opening for an hour or so.
How To Clean Amana Washing Machine Agitator — Quick Solution
The following are the steps on how to clean Amana washing machine agitators…
Step 1. Disconnect your washing machine from its electrical outlet before starting this fix.
Step 2. Open the lid of your washing machine. Using a flat-blade screwdriver, pry the cap off the agitator.
Step 3. Depending on the model of your machine, there will be a little filter inside the agitator. Take the filter out and rinse it thoroughly in a sink.
Step 4. Use a damp cloth to clean inside the agitator. Put the filter back in place and snap the cap onto the agitator.
Step 5. Close your washing machine’s lid and plug the power cord back into the power supply.
How To Clean Amana Washing Machine Drain Pump Filter — Simple Solutions
Clean the drain pump filter in your Amana washing machine with the following steps…
Step 1. Disconnect your washing machine from the power outlet in order to prevent electrocution.
Step 2. Spread a towel on the floor in front of your machine. Pry the lower front access panel off your washer and set it aside.
Step 3. Depending on your machine’s model, you’ll find a small capped hose under the panel. Pull the hose out and place a container underneath it.
Step 4. Pull the cap off the hose and let any water stuck in the washing machine drain out. Once you’ve drained all the water out of the machine, put the hose’s cap back on.
Step 5. Turn the drain pump filter knob next to the hose and pull it out (some water will still pour out).
Step 6. Take the pump filter to a sink and clean out any debris and lint that may be clogging the filter.
Step 7. Once the filter has been cleaned properly, put it back in place. Snap the lower front access panel back onto the cabinet.
Step 8. Plug your machine back into the power source and run a wash cycle to ensure that everything works fine.
Check out these other articles…
How To Clean Amana Washing Machine Drain Pump — Solved
To learn how to clean Amana washing machine drain pumps, take the following steps…
How To Clean Drain Pump In Amana Top Loader Washing Machine
Clean the drain pump in your top loader Amana washing machine with the following steps…
Step 1. In order to prevent water leaks and electrical damage, ensure that your washing machine is disconnected from the power outlet and the water valve is turned off before starting this procedure.
Step 2. Put some tape over your washing machine’s lid to secure it. Pull the drain hose out of the home drain.
Step 3. Using a pair of pliers, unscrew the two water supply hoses from the back of your machine (make sure to spread a rag on the floor underneath the hoses to catch any water leaks).
Step 4. With the help of another person, carefully tip the washing machine forwards and lay it on the floor.
Step 5. Using a pair of pliers, release the spring clamps on the two hoses attached to the drain pump. Pull both hoses off the pump (some water will spill, so ensure that you have a rag nearby).
Step 6. Unplug the wire connector attached to the pump assembly. Using a 5/16 inch nut-driver, loosen the nuts securing the drain pump to the bottom of the machine.
Step 7. Remove the drain pump from the machine and take it to a sink. Using a screwdriver, clean out any debris and lint that may be clogging the two ports on the drain pump.
Step 8. Once the drain pump has been cleaned, mount it back on the machine and apply the bolts with your nut-driver.
Step 9. Plug the wire connector back to the drain pump assembly. Reattach the two hoses to the ports on the drain pump and secure them using the retaining clamps.
Step 10. Lift your machine and set it on its feet. Reconnect the COLD and HOT water supply hoses from the ports a the back of your washing machine (In order to prevent water leaks, ensure that the hoses are secured properly).
Step 11. Peel the tape off your washing machine’s lid. Plug the power cord back into the electrical outlet and turn the water valve back on. Run a wash cycle to make sure the appliance works fine.
How To Clean Drain Pump In Amana Front Loader Washing Machine
Clean the drain pump in your Amana front loader washing machine using the following steps…
Step 1. Prevent electrocution by disconnecting your washing machine from the electrical outlet before starting this repair.
Step 2. Using a 1/4 inch nut-driver, remove the screws at the back of the machine securing the rear panel. Lift the panel off the cabinet and set it aside.
Step 3. Release the spring clamps on the outlet hoses connected to the drain pump and slide them out of place.
Step 4. Place a rag on the floor of the cabinet under the hoses. Pull each hose off the drain pump (water will spill out).
Step 5. Disconnect the wire harness connected to the drain pump. Use your nut-driver to loosen the nuts holding the pump to the bottom of the tub.
Step 6. Remove the pump assembly from the cabinet and take it to a sink. Using a tool such as a screwdriver, clean out any debris and lint inside the two ports on the pump assembly.
Step 7. Once the pump has been cleaned properly, mount it at the bottom of the tub and secure it using the screws. Plug the wire harness back into the pump assembly.
Step 8. Reattach the outlet hoses to the drain pump and secure them using the clamps.
Step 9. Snap the rear access back onto the cabinet and apply the mounting screws with your nut-driver. Plug your washing machine back into the electrical outlet.