If you are having issues with your Maytag washing machine shock absorber, this detailed guide gives you steps on how to deal with them…
Table of Contents
How To Test Maytag Washing Machine Shock Absorber — Solved
To test your Maytag washing machine shock absorber, follow the steps below…
Front Shocks
Take the following steps to test the front shocks absorbers in your Maytag washing machine…
Step 1. In order to prevent electrocution, disconnect your washing machine from the outlet before starting this repair.
Step 2. Go to the front of the machine, then slide the soap tray out of the dispenser. Release the tray from the housing by pressing the little tab inside. Take out the bolts holding the top panel. Lift the panel off and set it aside.
Step 3. Loosen the nut next to the dispenser opening. Pry the control panel off and set it on top of the cabinet. Use a Torx screwdriver to loosen the bolts holding the lower access panel to the cabinet. Pry the panel off and set it aside.
Step 4. Open your washing machine’s door. Loosen the nuts holding the door switch to the front panel using a Torx screwdriver.
Step 5. Use needle-nosed pliers or a flat-blade screwdriver to take the retaining wire off the door boot seal (take care not to damage the seal). Peel the door boot seal off the front panel.
Step 6. Loosen the bolts at the top and bottom of the main front panel using your screwdriver. Carefully lift the main front panel off the cabinet, then set it aside.
Step 7. Use a pair of pliers to grab the upper mount of one of the shock absorbers. Rotate the shock absorber, then pull it out off the bottom of the tub. Repeat this process with the lower mount.
Step 8. Take the shock absorber out of the cabinet. Try pulling the shock absorber apart and pushing it inwards. If you notice little or no resistance when pulling or pushing, the part is damaged and needs to be replaced. Repeat this process with the other front shock.
Step 9. If the shock absorber is in good condition, snap the lower mount back into the bottom of the tub, then rotate it. Push the upper mount into the opening at the bottom of the tub. Secure the shock absorber by rotating it.
Step 10. Remount the main front panel on the cabinet, then tighten the screws at the top and bottom using a Torx screwdriver.
Step 11. Snap the lower access panel onto the cabinet, then secure it with the screws. Snap the control panel onto the cabinet. Use your screwdriver to apply the screw next to the dispenser opening.
Step 12. Slide the detergent tray back into the housing. Open your washing machine’s door, then push the door lock back into place. Secure the door lock by applying the bolts with your Torx screwdriver.
Step 13. Refit the door boot seal around the front panel. Use a flat-blade screwdriver or needle-nosed pliers to fit the retaining wire around the door seal.
Step 14. Snap the control panel on the cabinet, then apply the screw next to the dispenser. Push the soap tray into the dispenser.
Step 15. Mount the top panel on the cabinet, then apply the screws at the back using a Torx screwdriver.
Step 16. Plug your washing machine into the electrical outlet, then try running a cycle to ensure that everything works properly.
Check out these other articles…
Maytag Washing Machine Error Codes [Proven Solutions]
Maytag Washing Machine Is Leaking [How To Fix]
Maytag Washing Machine Shakes Violently [Causes & Solutions]
Maytag Washing Machine Cycle [Detailed Guide, Problems & Solutions]
Maytag Washing Machine Is Not Spinning [How To Fix]
Clothes Stuck In A Maytag Washer [How To Fix]
Maytag Washing Machine Agitator [Problems, Solutions & Guide]
Rear Shocks
To test the rear Maytag washing machine shock absorbers, follow the steps below…
Step 1. Prevent any chances of electrocution by disconnecting your washing machine from the outlet before starting this repair.
Step 2. Loosen the bolts securing the rear access panel to the cabinet. Lift the panel off the cabinet and set it aside.
Step 3. Use pliers to grab the top of one of the rear shock absorbers. Rotate the shock, then pull it out of the bottom of the tub. Take out the lower shock mount in the same way.
Step 4. Take the shock absorber out of the cabinet. Try pulling the shock apart and pushing it inwards. If you feel little or no resistance, you’ll need to replace the part.
Step 5. If the shock absorber is in good condition, push the lower mount into the opening at the bottom of the tub. Push the upper mount into the opening at the bottom of the tub, then rotate it to secure.
Step 6. Mount the rear panel on the cabinet. Secure the rear panel by applying the Torx screws. Plug your washing machine back into the outlet.
