Washing Machine Motor [How To, Issues & Solutions]

This guide gives you all the information you need on washing machine motors…

Washing Machine Motor — How It Works

When an electrical current passes through the motor, it makes the pulley rotate. The drive belt looped around the motor pulley also turns the drive pulley at the bottom of the tub. This in turn, makes the drum spin.

Washing Machine Motor Overheating — Solved

If your washing motor is overheating, it’s most likely a result of an overloaded tub. The more clothes you have in your washer, the harder the motor will need to work in order to make the drum turn.

To prevent your washing machine motor from overheating, you need to make sure that the drum isn’t overfilled with clothes.

Washing Machine Motor Jammed — Solution

If your washing machine motor is jammed, the coupling is most likely the cause. Here are the steps you’ll need to take to replace this part…

Step 1. In order to prevent any chances of electrocution, please ensure that your washing machine is disconnected from the electrical outlet before starting this repair.

Step 2. With your Philips screwdriver, take out the screws on each end of the control panel. Lift the control panel and let it hang over the rear panel.

Step 3. Disconnect the wire harness attached to the top of the cabinet. Use a flat-blade screwdriver to pry out the two spring clips holding the rear access panel to the cabinet.

Step 4. Carefully lift the cabinet off the assembly and set it aside. Use a flat-blade screwdriver to pry the two clips holding the drain pump to the motor. Take the pump off the motor.

Step 5. Unplug the wire harness attached to the motor assembly. Take out the screws holding the motor retaining clips. Pry the motor clips off using a flat-blade screwdriver.

Step 6. Carefully lift the motor off the machine. Pull the coupler cog and isolator off the gear case drive shaft. Use a screwdriver to pry the second coupler cog off the motor.

Step 7. Discard the coupler pieces and take the new kit out of its packaging. Push one of the new cogs as far as possible onto the gear case drive shaft. Push the new isolator piece into place directly above it.

Step 8. Push the second coupler cog onto the motor. Lift the motor assembly and carefully slide it into place.

Step 9. Put the two retainer clips back onto the motor and apply the screws to secure them. Plug the wire harness into the motor assembly.

Step 10. Mount the drain pump onto the motor and secure it by snapping the two retaining clips into place.

Step 11. Lift the cabinet and put it back onto the washer. Use your flat-blade screwdriver to push the two spring clips back into the holes on the cabinet. Plug the wire connector back to the top of the cabinet.

Step 12. Lift the control panel and snap it back into the cabinet. Apply the screws using your screwdriver.

See also  Bosch Washing Machine Leaking [How To Fix]

Step 13. Plug your washing machine back into its electrical outlet and try running a wash cycle to ensure that the issue has been fixed.

Washing Machine Motor — How To Replace

Here’s how to replace your washing machine’s motor…

Drive Motor

To replace the drive motor in your washing machine here are the steps you’ll need to take…

How To Replace Drive Motor In Front Loader Washing Machine

To replace the drive motor in your front loader washing machine, do the following…

Step 1. Prevent electrocution by ensuring that your washing machine’s power supply is turned off.

Step 2. Use your screwdriver to loosen the bolts at the back of the machine holding the rear access panel. Take the panel off and set it aside.

Step 3. Take the drive belt off the drive pulley and motor pulley. Disconnect the wire connectors attached to the motor assembly (be sure to take note of where each connector goes).

Step 4. Use a socket wrench to remove the bolts holding the drive motor to the bottom of the outer tub. Carefully lift the motor assembly out of the cabinet and discard it.

Step 5. Prepare your new washing machine drive motor for installation by removing it from its packaging.

Step 6. Mount the new motor at the bottom of the outer tub and use your socket wrench to apply the bolts.

Step 7. Plug each wire connector into its appropriate terminal on the new motor. Snap the wires into the retainer.

Step 8. With the grooved side turned inwards, loop the drive belt around the drive pulley and motor pulley.

Step 9. Put the rear access panel back onto the cabinet and apply the screws with your screwdriver. Plug your washing machine back into the electrical outlet and ensure that the problem has been fixed by running a wash cycle.

How To Replace Drive Motor In Top Loader Washing Machine

Here are the steps on how to replace a drive motor in a top loader washing machine…

Step 1. In order to prevent electrical damage or water leaks, it is advised that you shut your washer’s water supply faucet and disconnect the power cord from its electrical outlet.

Step 2. Secure your washing machine’s lid using some tape. Pull the drain hose out of your home drain.

Step 3. Unscrew the two inlet hoses from the ports at the back of your machine (spread a towel on the floor under the hoses to catch any water leaks).

Step 4. With the help of another person, tip your washing machine forwards carefully and set it on the floor.

Step 5. With a nut-driver, take out the bolts holding the belt guard. Take the belt guard of and set it aside. Remove the drive belt from the two pulleys.

Step 6. Unplug the wire harness connected to the drive motor and release the wire from the retainer.

Step 7. With your socket wrench, loosen the bolts holding the drive motor to the mounting plate. Carefully lift the motor off the plate and discard it.

Step 8. Prepare your new washing machine drive motor for installation by removing it from its packaging.

Step 9. Mount the new drive motor at the bottom of the machine and secure it by applying the bolts with your socket wrench.

Step 10. Plug the wire connector into the new motor and secure the wire in the retainer.

Step 11. Loop the drive belt around the two pulleys (ensure that the grooved side is turned inwards).

Step 12. Put the belt guard over the drive belt and apply the nuts with your socket wrench. Set your washing machine onto its feet and peel the tape off the lid.

See also  Whirlpool Washing Machine Belt [Issues & 5 Proven Solutions]

Step 13. Insert the drain hose back into your home drain. Reattach the two water inlet hoses to the ports on your washing machine.

Step 14. Plug the power cord back into the electrical outlet, then turn the water supply faucet back on. Make sure the problem has been fixed by running a wash cycle.

Motor Stator

Here are the steps you’ll need to take to replace your washing machine motor stator…

How To Replace Top Loader Washing Machine Motor Stator

Do the following to replace your top loader washing machine motor stator…

Step 1. Prevent electrocution and water spillage by unplugging your washer from the electrical outlet and shutting the water supply valve before starting this repair.

Step 2. Spread a towel on the floor underneath the water supply hoses at the back of your washer. Use a pair of pliers to unscrew the two hoses (some water will spill out).

Step 3. Tip the washing machine forwards carefully and set it on the floor (get someone to help you if needed).

Step 4. With an adjustable wrench and a hammer, loosen the bolt holding the rotor assembly to the bottom of the tub. Carefully pull the rotor assembly off the tub and set it aside.

Step 5. Loosen the bolts holding the stator to the bottom of the outer tub using a 10mm socket wrench. Disconnect the wire connectors attached to the stator, then discard it.

Step 6. Remove your new washing machine motor stator from its packaging. Plug the wire harnesses into the corresponding terminals on the new stator.

Step 7. Mount the new stator at the bottom of the machine and apply the bolts with your 10mm socket wrench to secure it.

Step 8. Put the rotor assembly over the stator and tighten the bolt using your adjustable wrench. Carefully lift your washing machine and set it on its feet.

Step 9. Reconnect the two water supply lines to the back of your machine (ensure that you secure both hoses properly so water doesn’t leak out).

Step 10. Reconnect your washing machine to its electrical outlet and turn the water supply faucet back on. Run a wash cycle to ensure that the machine works properly.

Check out these other articles…

Amana Washing Machine Shakes Violently [Proven Solution]

Amana Washing Machine Stops [How To Fix]

Amana Washing Machine Door Won’t Open [Quick Fix]

Cold Water In Washing Machine [Issues & Solutions]

Amana Washing Machine Squeaking [How To Fix]

Amana Washing Machine Not Turning On [Proven Solutions]

Amana Washing Machine Smells [How To Fix]

How To Replace Front Loader Washing Machine Motor Stator

To change the motor stator in your front loader washing machine, here are the steps you’ll need to take…

Step 1. Prevent electrocution by ensuring that your washing machine is disconnected from the power supply.

Step 2. Go to the back of the machine and use your Philips screwdriver to remove the screws securing the rear access panel. Lift the panel off the cabinet and set it aside.

Step 3. Use a 19mm socket wrench to loosen the bolt holding the rotor assembly. To make this easier, try jamming the rotor by inserting a screwdriver into one of the three inner holes.

Step 4. Pry the rotor assembly off the machine carefully and set it aside. Take note of the positioning of each wire harness attached to the motor stator and disconnect them.

Step 5. Using a 10mm socket wrench, loosen the bolts securing the motor stator to the back of the tub. Lift the stator off the tub and discard it.

See also  Bosch Washing Machine Power [3 Problems & Quick Solutions]

Step 6. Prepare your new washing machine motor stator for installation by removing it from its packaging.

Step 7. Mount the new stator at the back of the outer tub and apply the bolts using your 10mm socket wrench.

Step 8. Plug each wire connector into the appropriate terminal on the new stator. Put the rotor assembly over the stator and apply the bolt using your 19mm socket wrench.

Step 9. Snap the rear access panel back onto the cabinet and apply the screws with a Philips screwdriver.

Step 10. Plug your washing machine back into the electrical outlet and test the machine by running a wash cycle.

Washing Machine Drain Motor Not Working — How To Fix

If your washing machine drain pump motor isn’t working, it will need to be replaced. Here are the steps you’ll need to follow…

How To Replace Drain Motor In Front Loader Washing Machine

Replace the drain motor in your front loader washing machine with the following steps…

Step 1. Make sure your washing machine is unplugged from the power supply before starting this repair.

Step 2. With your screwdriver, remove the bolts at the back if the cabinet securing the rear access panel. Lift the panel off and set it aside.

Step 3. Reach under the tub and disconnect the wire harnesses attached to the drain pump.

Step 4. Place a rag and a small container near the drain pump. With your pliers, release the clamp on the hose attached to the pump and slide it out of place. Pull the hose off the pump (expect some water to spill out).

Step 5. Use a screwdriver to remove the bolts holding the drain pump to the bottom of the machine. Take the drain pump out of the cabinet and discard it.

Step 6. Remove your new washing machine drain motor from its packaging. Mount the new motor at the bottom of the machine and apply the screws to secure it.

Step 7. Connect the hose to the port on the new drain motor and secure it with the spring clamp. Plug the wire connectors to the new motor.

Step 8. Put the rear panel back onto the cabinet and apply the screws to secure. Plug the machine back into the electrical outlet. To ensure everything works properly, try running a wash cycle.

How To Replace Drain Motor In Top Loader Washing Machine

To replace the drain motor in your top loader washing machine, here are the steps you’ll need to take…

Step 1. Turn your washer’s water supply faucet off and disconnect the power cord from the electrical outlet before starting this repair.

Step 2. Loosen the two water supply hoses from the ports at the back of the machine (use a pair of pliers if needed).

Step 3. Put some tape on your washing machine’s lid to secure it. Pull the drain hose out of your home drain.

Step 4. Tip your washing machine forwards carefully and set it on the floor. Disconnect the wire harness attached to the drain motor.

Step 5. Use a pair of pliers to squeeze the spring clamp on the hose attached to the drain pump, then slide it out of place. Pull the hose off the pump (some water will spill out).

Step 6. Use a screwdriver to remove the bolts holding the pump assembly to the bottom of the tub. Discard the old pump and take the new one out of its packaging.

Step 7. Mount the new drain pump at the bottom of the machine and apply the bolts with your screwdriver to secure it.

Step 8. Reattach the outlet hose to the port on the drain pump and secure it using the spring clip.

Step 9. Plug the wire connectors into the terminals on the new drain pump. Lift your washing machine back onto its feet.

Step 10. Push the drain hose back into the home drain. Reconnect the two water supply hoses to the ports at the back of the washer (ensure that the hoses are secured properly so water won’t spill out).

Step 11. Reconnect the power cord to the electrical outlet and turn the water supply valve back on. To make sure the problem has been fixed, try running a wash cycle.