Whirlpool Washing Machine Won’t Turn On [Proven Solutions]


If your Whirlpool washing machine won’t turn on, you’ve come to the right place. This detailed guide gives you steps on how to handle the issue…

Whirlpool Washing Machine Won’t Turn On — How To Fix

If your Whirlpool washing machine won’t turn on, look for the following issues…

1. Faulty Power Outlet

If your Whirlpool washing machine won’t turn on, the first thing you should do is check to ensure that the power outlet is working. To do this, unplug your washer from the outlet, then try plugging another appliance in.

If the second appliance doesn’t work, it indicates that the power outlet is damaged. To fix this issue, we recommend contacting an electrician.

2. Power Cord Is Burnt

If your Whirlpool washing machine won’t turn on, the second thing you should check is the power cord. The following are steps on how to replace a burnt power cord in your washing machine…

Front Loaders

Take the following steps to replace your Whirlpool front loader washing machine’s power cord…

Step 1. Unplug your washer’s power cord from the electrical outlet before starting this repair in order to prevent electrocution.

Step 2. Using a 1/4 inch nut-driver, take out the screws at the back of the machine holding the top panel. Lift the panel off the cabinet and set it aside.

Step 3. Unplug the power cord wires connected to the line filter on the cabinet (make sure to note where each wire goes).

Step 4. Using your nut-driver, loosen the screw holding the grounding wire to the cabinet. Using pliers, rotate the power cord strain relief, then pull it out of the cabinet.

See also  Electrolux Washing Machine Not Filling With Water [How To Fix]

Step 5. Discard the old power cord and take the new one out of its packaging. Pass the connectors of the new power cord through the opening at the back of the cabinet.

Step 6. Plug the connectors into the appropriate terminals on the line filter. Put the grounding wire back in place, then use your nut-driver to tighten the bolt.

Step 7. Place the top panel on the cabinet, then tighten the three screws at the back using a 1/4 inch nut-driver.

Step 8. Plug the new power cord into the electrical outlet. In order to ensure that everything works properly, try running a wash cycle.

Check out these other articles…

Whirlpool Washing Machine Shakes [Proven Solutions]

Whirlpool Washing Machine Motor [Issues, Solutions & Guide]

Whirlpool Washing Machine Timer [Problems, Solutions & Guide]

Whirlpool Washing Machine Making Noise [Proven Solutions]

Whirlpool Washing Machine Balance [Problems, Solutions & Guide]

Whirlpool Washing Machine Cycle [Problems, Solutions & Guide]

Whirlpool Washing Machine Just Hums [Proven Solutions]

Top Loaders

Follow the steps below to replace the power cord in your top loader Whirlpool washing machine…

Step 1. Shut the water supply faucets and disconnect the power cord from the electrical outlet before starting this procedure in order to prevent electrical damage and water leaks.

Step 2. Use a pair of pliers to disconnect the HOT and COLD water inlet hoses from the ports at the back of your machine (ensure that you keep a rag nearby to clean any leaks).

Step 3. With a 1/4 inch nut-driver, take out the bolts at the back of the machine holding the control panel to the cabinet.

Step 4. Lift the control panel assembly, then set it face-down on top of the washer’s lid. Unplug the control panel wire connector from the main control board, then set it aside.

See also  Electrolux Washing Machine Keeps Filling With Water [How To Fix]

Step 5. Use the nut-driver to take out the bolts holding the upper rear panel. Slide the panel upwards, then pull it off the machine.

Step 6. Unplug the power cord’s wire connector from the line filter and control board. Using a nut-driver, loosen the screw holding the grounding wire to the top panel.

Step 7. Use your nut-driver to take out the bolts holding the top panel. Loosen the screw securing the wiring and tube guard, then take it off.

Step 8. Lift the top panel and support it. Using a pair of needle-nosed pliers, release the power cord retainer from the top panel.

Step 9. Lower the top panel on the cabinet, then tighten the screws at the back using your nut-driver.

Step 10. Discard the old power cord, then take the new power cord out of its packaging. Put the wiring and tube guard back in place, then apply the bolts.

Step 11. Snap the power cord retainer into the slot on the top panel. Plug the connectors into the appropriate terminals.

Step 12. Put the upper rear access panel back on, then tighten the bolts. Plug the control panel wire connector into the control board.

Step 13. Snap the control panel onto the cabinet, then tighten the screws at the back. Reconnect the water inlet hoses.

Step 14. Plug the new power cord into the electrical outlet, then turn the water faucets back on. Try running a cycle to ensure everything works properly.

Electric Dryers

To replace the power cord in your Whirlpool electric dryer, take the following steps…

See also  Maytag Washing Machine Agitator [2 Problems, Solutions & Detailed Guide]

Step 1. Unplug your dryer’s power cord from the outlet before starting this procedure in order to prevent electrical damage.

Step 2. Use a 1/4 inch nut-driver to take out the screws holding the terminal block access plate to the back of the cabinet. Take the plate off and set it aside.

Step 3. Use your nut-driver to loosen the three screws holding the three power cord wires to the terminals. Take out the bolt holding the grounding wire to the cabinet.

Step 4. Loosen the bolt holding the power cord strain relief. Pull the cord and strain relief out of the cabinet.

Step 5. Take your new power cord out of its packaging. With your screwdriver, loosen the nuts holding the new strain relief to the power cord. Separate the two halves of the relief.

Step 6. Insert the two halves of the strain relief in the power cord opening at the back of the cabinet. Put the screws in, then loosely tighten them to secure the relief.

Step 7. Pass the power cord wires through the opening at the back of the cabinet. Place each connector on the appropriate terminal, then secure by applying the bolts.

Step 8. Put the grounding wire into place, then use your screwdriver to apply the bolts. Properly tighten the strain relief screws.

Step 9. Put the terminal block access panel back into place, then apply the screws to secure it. Plug the new power cord into the electrical outlet, then try running a cycle to ensure everything works properly.