If your Amana washing machine smells, this detailed guide will give you steps on how to deal with the problem…
Table of Contents
Amana Washing Machine Smells — Solved
If your Amana washing machine smells, here are the issues you should look for…
1. Detergent And Mould Build-up
Deal with mould and detergent build-up in your Amana washing machine with the following steps…
Step 1. Take any items of clothing out of your washer’s tub.
Step 2. Pull out the detergent drawer and take it to a sink. Thoroughly wash out any accumulated detergent.
Step 3. Once the drawer is clean, push it back into the housing. Pour about 2 cups of white vinegar into the detergent drawer (this kills mould and gets rid of foul smell).
Step 4. Turn your washing machine on and set a wash cycle with the highest water temperature. Press Start to begin the cycle.
Step 5. Once the wash cycle is completed, use a rag to clean the grooves of the door boot seal. Leave the washer’s door open for a few hours to let the tub air out.
2. Drive Belt Is Worn
If your washer’s drive belt is worn, your Amana washing machine will begin to produce a burning smell. Here are the steps you’ll need to take to replace the drive belt in your Amana washing machine…
How To Replace Worn Belt In Front Loader Amana Washing Machine
Replace your top loader Amana washing machine’s drive belt with the following steps…
Step 1. Unplug your washing machine from the power outlet in order to prevent electrocution.
Step 2. Loosen the nuts at the back of your washing machine securing the rear panel. Pull the panel off the machine and set it aside.
Step 3. If still intact, take the drive belt off the motor pulley and drive pulley, then discard it.
Step 4. Prepare the new drive belt for installation by removing it from its packaging. With the grooved side turned inwards, loop the new belt around the motor pulley and drive pulley.
Step 5. Place the rear panel on the machine and use your nut-driver to apply the bolts. Plug the power cord to the outlet and try running a spin cycle to make sure the problem has been fixed.
How To Replace Worn Belt In Top Loader Amana Washing Machine
Follow the steps below to replace a worn drive belt in your Amana top loader washing machine…
Step 1. Shut your washing machine’s water supply faucet and disconnect the power cord from the outlet in order to avoid water leaks and electrocution.
Step 2. Pull your washer’s drain hose out of the home drain. Use a pair of pliers to disconnect the COLD and HOT water inlet hoses from then ports at the back of your washing machine (we recommend keeping a rag nearby to clean any water leaks).
Step 3. With the help of another person, tip your washing machine forwards carefully and set it on the floor.
Step 4. With a 5/16 inch nut-driver, remove the bolts holding the belt guard. Remove the drive belt from the transmission pulley and motor pulley.
Step 5. Remove your new washing machine drive belt from its packaging and loop it around the two pulleys (make sure the grooved side is turned inwards).
Step 6. Put the belt guard back on and apply the bolts to secure it. Set your washing machine back onto its feet.
Step 7. Insert the drain hose back into the home drain and reconnect the water supply lines to the machine.
Step 8. Turn your washer’s water supply faucet back on and plug the power cord back into the electrical outlet. To make sure the problem has been fixed, try running a spin cycle.
3. Burnt Capacitor (Top Loaders)
A burn capacitor can cause your top loader Amana washing machine to smell. To replace this part, here are the steps you’ll need to take…
Step 1. In order to prevent any damage, make sure your washing machine is unplugged from the power outlet and the water valve is shut.
Step 2. Pull your washing machine’s drain hose out of the home drain. Spread a towel on the floor underneath the water supply hoses to catch any leaks. Unscrew the two hoses from the back of your machine (use pliers if needed).
Step 3. Carefully tip your washing machine forwards and set it on the floor (get someone to help you if needed).
Step 4. Unplug the wire harness connected to the capacitor at the bottom of your machine. Use a screwdriver to remove the bolt holding the capacitor. Take the capacitor off your washer and discard it.
Step 5. Remove the new capacitor from its packaging, then mount it at the bottom of the washer. Apply,the nut with your screwdriver to secure it.
Step 6. Lift your washing machine onto its feet carefully and insert the drain hose back into the drain pipe.
Step 7. Reconnect the two water supply hoses to the ports at the back of the machine (take care to secure the hoses properly so water doesn’t spill out).
Step 8. Turn your washing machine’s water supply faucet back on and reconnect the power cord to the electrical outlet. Ensure that the smell is gone by running a wash cycle.
4. Burnt Motor
To change a burnt motor in your Amana washing machine, here are the steps you’ll need to take…
Motor Stator
Do the following to replace the motor stator in your Amana washing machine…
How To Replace Motor Stator In Top Loader Amana Washing Machine
Here are the steps you’ll need to take to replace the motor stator in your Amana top loader washing machine…
Step 1. Unplug your washing machine’s power cord from the electrical outlet before starting this repair in order to prevent electrocution.
Step 2. Put some tape on your washing machine’s lid to secure it. Tip the machine backwards carefully and set it against a wall.
Step 3. Turn the rotor so that one of the holes lines up with a hole on the stator. Push a small screwdriver into the holes to jam the rotor.
Step 4. Using a 1/4 inch Allen wrench, loosen the nut holding the rotor assembly to the bottom of the tub. Carefully pry the rotor off and set it aside.
Step 5. Remove the bolts holding the stator to the bottom of the tub with a 3/8 inch socket wrench. Take the stator and mounting plate off the machine.
Step 6. Disconnect the wire connectors plugged into the stator and set the stator aside.
Step 7. Prepare your new washing machine motor stator for installation by removing it from its packaging.
Step 8. Plug the wire harnesses into the new stator. Place the stator and mounting plate at the bottom of the tub and apply the bolts with your socket wrench.
Step 9. Put the rotor assembly over the rotor. Tighten the nut with the Allen wrench to secure the rotor.
Step 10. Set your washing machine back onto its feet and peel the tape off the lid. Turn the power supply back on and try running a wash cycle to make sure the problem has been fixed.
Check out these other articles…
Amana Washing Machine Shakes Violently [Proven Solution]
Cold Water In Washing Machine [Issues & Solutions]
Amana Washing Machine Squeaking [How To Fix]
Amana Washing Machine Not Turning On [Proven Solutions]
Washing Machine Motor [How To, Issues & Solutions]
How To Replace Motor Stator In Front Loader Amana Washing Machine
To replace the motor stator in your front loader Amana washing machine, here are the steps you’ll need to take…
Step 1. Make sure your washing machine is disconnected from the power outlet in order to prevent electrocution.
Step 2. Use a 1/4 inch nut-driver to loosen the bolts a the back of the machine securing the top panel. Pull the panel backwards about an inch or so, then lift it off the machine.
Step 3. Use the screwdriver to take out the nuts securing the rear access panel. Lift the panel off the machine and set it aside.
Step 4. Insert a small screwdriver into one of the inner holes on the rotor assembly (this will jam the rotor).
Step 5. With an 11/16 inch socket wrench, take out the bolt holding the rotor assembly to the back of the machine. Carefully pry the rotor off.
Step 6. Use a flat-blade screwdriver to pry the control board wire cover. Unplug the wire harness of the motor stator from the control board. Release the wires from the retainer using a pair of needle-nosed pliers.
Step 7. Use your socket wrench to take out the bolts holding the stator to the back of the machine. Pull the stator out of the cabinet, then discard it.
Step 8. Prepare your new washing machine motor stator for installation by removing it from its packaging.
Step 9. Mount the new motor stator at the back of the machine and apply the bolts with your socket wrench.
Step 10. Snap the retainers on the new motor stator wire into the holes on the cabinet. Plug the electrical connector of the new stator into the control board. Snap the cover of the control board.
Step 11. Place the rotor assembly on the stator and apply the bolt using your socket wrench.
Step 12. Lift the rear panel and snap it back onto the cabinet. Apply the bolts to secure it.
Step 13. Place the top panel on the machine and and use your nut-driver to apply the bolts at the back.
Step 14. Plug your washing machine back into the electrical outlet and try running a wash cycle to ensure that the problem has been fixed.
Drive Motor
To replace the drive motor in your Amana washing machine, do the following…
How To Replace Drive Motor In Amana Top Loader Washing Machine
Replace the drive motor in your top loader Amana washing machine with the following steps…
Step 1. Prevent water leakage and electrical damage by shutting the water supply to your washing machine and disconnecting the power cord from the outlet.
Step 2. Pull your washing machine’s drain hose out of the standpipe. Loosen the HOT and COLD water supply hoses from the ports at the back of your washing machine (keep a rag handy to clean any water leaks).
Step 3. With the assistance of another person, tip your washing machine forwards carefully and set it on the floor.
Step 4. Use a 5/16 inch nut-driver to remove the bolts holding the belt guard. Remove the drive belt from the transmission pulley and motor pulley.
Step 5. Disconnect the wire harness attached to the motor assembly and release the wire from the retainer.
Step 6. With a socket wrench, loosen the bolts holding the motor assembly to the bottom of the machine. Take the motor off and set it aside.
Step 7. Prepare your new washing machine drive motor for installation by removing it from its packaging.
Step 8. Mount the new drive motor at the bottom of the machine and apply the bolts with your socket wrench to secure it.
Step 9. Plug the wire harness into the new motor assembly and secure the wires in the retainer.
Step 10. Loop the drive belt around the transmission pulley and drive pulley. Put the belt guard back on and apply the bolts.
Step 11. Carefully set your washing machine on its feet and insert the drain hose into the home drain.
Step 12. Reattach the two water supply hoses to the ports at the back of the machine (in order to prevent any chances of water leakage, ensure that both hoses are properly secured).
Step 13. Plug your washing machine’s power cord back into the electrical supply and turn the water faucet back on. Test the washing machine by running a wash cycle.
How To Replace Drive Motor In Amana Front Loader Washing Machine
Here are the steps you’ll need to take to replace the drive motor in your Amana front loader washing machine…
Step 1. Prevent any chances of electrocution by unplugging your washer’s power cord from the electrical outlet before starting this repair.
Step 2. Using a 1/4 inch nut-driver, loosen the bolts at the back of your machine securing the rear access panel. Lift the rear panel off the washer and set it aside.
Step 3. Carefully take the drive belt off the motor pulley and drive pulley. Unplug the wire connectors attached to the motor assembly (ensure that you note where each connector goes).
Step 4. Release the wires from the retainer. Using a socket wrench, remove the mounting bolts holding the motor assembly to the bottom of the outer tub. Carefully lift the motor out of the cabinet and discard it.
Step 5. To install your new washing machine drive motor, take it out of its packaging. Mount the new drive motor at the bottom of the tub. Secure the bolts using your socket wrench.
Step 6. Connect each plug to its appropriate terminal on the new motor and secure the wires in the retainer.
Step 7. Loop the drive belt around both pulleys. Place the rear access panel back on the cabinet and secure it by applying the bolts.
Step 8. Reconnect your washer to the electrical outlet and ensure that the problem has been fixed by running a wash cycle.
5. Burnt Control Board
If your Amana washing machine smells burnt, the final thing you should check is the control board. Here are the steps you’ll need to take to replace this part…
How To Replace Burnt Control Board In Amana Front Loader Washing Machine
Do the following to replace a damaged control board in your front loader Amana washing machine…
Step 1. Make sure your washing machine is unplugged from the power outlet in before starting this repair.
Step 2. Loosen the nuts at the back of the machine securing the top panel. Pull the panel back about an inch or so, then lift it off the machine.
Step 3. Use a flat-blade screwdriver to pry the cap off the control board. Take note of the positioning of each wire harness, then unplug them from the control board.
Step 4. With your flat-blade screwdriver, pry the control board off the mounts at the side of the cabinet. Pull the control board out of the machine, then discard it.
Step 5. To prepare your new control board for installation, remove it from its packaging.
Step 6. Snap the new control board into the mounts on the cabinet. Plug each wire connector into its appropriate terminal on the new board. Snap the cap onto the board.
Step 7. Slide the top panel onto the cabinet and apply the bolts to secure it. Reconnect your washing machine to its electrical supply, then ensure that the washer works properly by running a wash cycle.
How To Replace Burnt Control Board In Amana Top Loader Washing Machine
To change the control board in your Amana top loader washing machine, take the following steps…
Step 1. Make sure your washing machine’s power cord is unplugged from the electrical outlet in order to prevent electrocution.
Step 2. Insert a tool such as a putty knife underneath the two bottom corners of the control panel. Detach the control panel from the base and set it face-down on top of the cabinet.
Step 3. Pull the air pressure tube off the port on the control board. Unplug each wire connector attached to the control board (make sure to take note of where each connector goes).
Step 4. Release the wires from the retainers. Use a screwdriver to take out the bolts holding the control board to the panel. Lift the control panel and pull the selector knob off the shaft.
Step 5. Take the control board off the panel and discard it. Prepare your new control board for installation by removing it from its packaging.
Step 6. Mount the new control board on the panel and apply the screws with your screwdriver. Lift the control panel and snap the selector knob onto the shaft.
Step 7. Plug each electrical connector into its appropriate terminal on the new control board and secure the wires in the retainers.
Step 8. Plug the air pressure tube to the port on the new board. Lift the control panel and snap it back into the cabinet. Reconnect your washing machine to the electrical outlet, and try running a wash cycle to ensure that the problem has been fixed.