If you are getting different Frigidaire washing machine error codes, you’ve come to the right place. This guide will explain the meanings of these errors and show you how to fix them. So, without wasting any more time, let’s begin…
Table of Contents
Frigidaire Washing Machine Error Code E4 — Solved
An E4 error code on your Frigidaire washing machine indicates that the load is unbalanced. This is caused by overloading or under-loading the drum. To avoid an unbalanced load, ensure that your drum is roughly 3/4 full. Its also a good idea to distribute your clothes evenly in the drum.
Frigidaire Washing Machine Error Code E11 — Solution
If you are getting the Frigidaire washing machine error code E11, it indicates that the washer is spending too much time trying to fill. Here are the things that could cause this issue…
1. Water Supply Is Off
Ensure that you fully open your washing machine’s water supply before attempting any repairs. If the water supply isn’t on, the E11 error code could pop up on your washing machine’s display.
2. Water Inlet Filters Are Blocked
Here’s what you’ll need to do in order to clean the water inlet filters in your Frigidaire washing machine…
Step 1. Turn off your washing machine’s water supply and unplug the power cord before attempting any repairs. This will prevent any chances of water leakage and electrocution.
Step 2. Disconnect the water inlet hoses from the inlet ports at the back of your washing machine (ensure that you keep a rag nearby in case water spills out of the ports).
Step 3. Use a pair of pliers to pull the little mesh filters inside the inlet ports. Take the filters to a sink and rinse out any dirt that may have clogged them. Once the filters are clean, put them back in place.
Step 4. Reconnect the inlet hoses to the water inlet ports then turn on the water and power supply. Make sure the issue has been fixed by running a wash cycle.
3. Damaged Water Inlet Valve
Here’s what you’ll need to do to replace the water inlet valve in your Frigidaire washing machine…
How To Replace Frigidaire Top Loader Washing Machine Water Inlet Valve
Do the following to replace the water inlet valve in your Frigidaire top loader washing machine…
Step 1. Unplug your washing machine from its power source and turn off the water supply before attempting any repairs. This prevents any chances of water leakage and electrocution.
Step 2. Put some tape over the lid of your washing machine. Disconnect the water inlet hoses from the inlet ports at the back of your washing machine (ensure that you keep a rag nearby in case water spills out).
Step 3. Insert a putty knife under the main top panel of your washing machine to release the retaining clips. Lift the top panel up and support it.
Step 4. the water inlet valve will be mounted inside the cabinet beside the drum. Use a pair of pliers to press the clamp on the hose connected to the valve and slide the clamp out of place. Disconnect the hose from the water inlet valve.
Step 5. Disconnect the electrical connectors attached to the water inlet valve (ensure that you take note of the positioning of each connector).
Step 6. Use a Philips screwdriver to take out the screws at the back of your washing machine holding the water inlet valve. Pull the water inlet valve assembly out of your washing machine and set it aside.
Step 7. Take the water inlet valve assembly out of its packaging and install it in your washing machine. Apply the screws at the back with your Philips screwdriver to secure it.
Step 8. Connect the hose to the new water inlet valve and slide the retaining clamp in place. Connect each electrical connector to its appropriate terminal on the new water inlet valve.
Step 9. Lower the main top panel of your washing machine and snap it back onto the machine. Connect the water inlet hoses back to the inlet ports at the back of your washing machine (ensure that the connection is properly secured in order to prevent water leakage).
Step 10. Remove the tape from the lid off your washing machine. Turn on your washing machine’s water supply and plug the power cord back in. Run a wash cycle to ensure that everything is working properly.
How To Replace Frigidaire Front Loader Washing Machine Water Inlet Valve
Do the following to replace the water inlet valve in your Frigidaire front loader washing machine…
Step 1. Ensure that you unplug your washing machine’s power cord and turn off the water supply before attempting any repairs in order to avoid electrocution and water leakage.
Step 2. Unscrew the water inlet hoses from the water inlet ports at the back of your washing machine (some water may spill out when you do this, so make sure to keep a rag nearby).
Step 3. Use a Philips screwdriver to take out the screws at the back of your washing machine holding the top panel. Slide the top panel back and lift it off the machine.
Step 4. Take out the two screws at the back of your washing machine holding the the water inlet valve. Pull the water inlet valve out of your washer. Disconnect the electrical connectors attached to the water inlet valve (make sure to take note of where each connector goes).
Step 5. Use a pair of pliers to press the clamp on the hose connected to the water inlet valve and slide the clamp out of place. Disconnect the hose from the water inlet valve and set the valve aside.
Step 6. Take your new washing machine water inlet valve out of its packaging. Connect the hose to the new valve and slide the retaining clamp in place. Install the new water inlet valve in your washing machine and apply the two screws at the back with your Philips screwdriver to secure.
Step 7. Connect each electrical connector to its appropriate terminal on the new water inlet valve. Slide the top panel of your washing machine back on and apply the screws at the back to secure.
Step 8. Connect the water inlet hoses to the inlet ports at the back of your washing machine. Plug your washing machine back to its power source and turn on the water supply. Make sure the issue has been fixed by running a wash cycle.
Check out these other articles…
Candy Washing Machine Error Codes [Quick Fix]
Candy Washing Machine Not Working [Solved]
Candy Washing Machine Tripping Electric [Quick Fix]
How To Clean Candy Washing Machine [Detailed Guide]
Frigidaire Washing Machine Not Draining [Issues Fixed]
How To Replace Belt On Frigidaire Washing Machine [Quick Guide]
Frigidaire Washing Machine Error Code E21 — Solved
If you are getting the Frigidaire washing machine error code E21, it indicates that there is an issue with the drainage system. To learn how to fix drainage issues, read this article.
Frigidaire Washing Machine Error Code E35 — Solution
A Frigidaire washing machine E35 error code indicates that the water pressure switch has detected water overflow. If your washing machine is overflowing, you’ll need to replace the water inlet valve. However, if your washing machine isn’t overflowing, it indicates that the water pressure switch is faulty. Here’s how to replace this part…
How To Replace Frigidaire Top Loader Washing Machine Water Pressure Switch
Do the following to replace the water pressure switch in your Frigidaire top loader washing machine…
Step 1. Ensure that you unplug your washing machine’s power supply and turn off the water valve before attempting any repairs (this is to prevent any chances of water leakage and electrocution).
Step 2. Use a Philips screwdriver to take out the screws at the back of your washing machine holding the control panel cover. Pull the cover off and set it aside.
Step 3. Pull the water pressure switch knob from the control panel (if needed, use some string to help pull it off). Use a screwdriver to remove the screw inside the pressure switch knob housing (this will release the water pressure switch).
Step 4. Pull the water pressure switch out of your washing machine then disconnect the tube and wires connected to it. Take your new water pressure switch out of its packaging and connect the tube and wires to it.
Step 5. Insert the new water pressure switch into the control panel and apply the screw with your Philips screwdriver to secure it. Snap the knob back in place. Put the back of the control panel on and apply the screws with your screwdriver to secure.
Step 6. Plug your washing machine back to its power supply and turn the water supply back on. Make sure everything is working properly by running a wash cycle.
How To Replace Frigidaire Front Loader Washing Machine Water Pressure Switch
Do the following to replace the water pressure switch in your Frigidaire front loader washing machine…
Step 1. Avoid water leakage and electrocution by making sure to turn off your washing machine’s water supply and unplug the power cord before attempting any repairs.
Step 2. Use your Philips screwdriver to remove the screws at the back of your washing machine holding the top panel. Slide the panel backwards and lift it off your washing machine.
Step 3. Release the water pressure switch from the support bracket by removing the retaining screw with your Philips screwdriver. Disconnect the wires connected to the water pressure switch (make sure to take note of the positioning of each wire).
Step 4. Press the clamp on the tube connected to the water pressure switch out of place. Detach the tube from the pressure switch and set the switch aside.
Step 5. Take your new water pressure switch out of its packaging. Connect the new switch to the tube and slide the retaining clamp in place. Connect the electrical connectors to the new water pressure switch.
Step 6. Put the water pressure switch back on the mounting bracket and apply the screw to secure it. Slide the top panel of your washing machine back on and apply the screws at the back with your Philips screwdriver to secure it.
Step 7. Turn on your washing machine’s water supply and plug the power cord back in. Run a wash cycle to make sure everything is working properly.
Frigidaire Washing Machine Error Code Error Code E41 — How To Fix
A Frigidaire washing machine error code E41 indicates that the door of the machine isn’t locked. This is often caused by not shutting the door properly. Make sure to firmly shut your washing machine’s door before starting a cycle. If your washing machine’s door isn’t shutting, you’ll need to replace the door lock. Here’s how to do this…
How To Replace Frigidaire Front Loader Washing Machine Door Lock
Here’s what you’ll need to do in order to replace the door lock in your Frigidaire front loader washing machine…
Step 1. Unplug your washing machine’s power cord and turn off the water supply before attempting any repairs in order to avoid electrocution or water leakage.
Step 2. Open the door of your washing machine. Insert a flat-blade screwdriver under the retaining band around the door boot seal. Work the screwdriver around until the entire band comes off.
Step 3. Peel the door seal away from the door opening. Use a Philips screwdriver to take out the two screws holding the door lock to your washing machine. Reach inside the washing machine and pull the lock out of place. Disconnect the electrical connectors attached to the door lock assembly and set the old lock aside.
Step 4. Take your new washing machine door lock out of its packaging and connect the two electrical connectors to it. Put the new door lock in place inside your washing machine and apply the two screws with your Philips screwdriver to secure it.
Step 5. Fit the door seal back in place around the door opening. Fit the retaining band around the door seal (you may need a flat-blade screwdriver to do this).
Step 6. Close the door of your washing machine. Plug your washing machine back to its power source and turn on the water supply. Run a wash cycle to make sure everything is working properly.
How To Replace Frigidaire Top Loader Washing Machine Door Lock
Do the following to replace the door lock in your Frigidaire top loader washing machine…
Step 1. Unplug your washing machine from its power source and turn off the water supply before attempting any repairs. This will prevent electrocution and water leakage.
Step 2. Put some tape on the lid of your washing machine. Insert a putty knife under the main top panel of your washing machine to release the retaining clips. Lift the top panel up and support it.
Step 3. Use a Philips screwdriver to take out the screw holding the door lock to the bottom of the top panel. Pull the lock off the panel and disconnect the electrical connectors.
Step 4. Take your new door lock out of its packaging. Screw the new door lock to the top panel and connect the electrical connectors to it. Lower the main top panel and snap it into place.
Step 5. Pull the tape off the lid of your washing machine. Plug your washing machine back to its power source and turn on the water supply. Run a wash cycle to make sure everything is working properly.
Frigidaire Washing Machine Error Code E90 — Quick Fix
If you are getting a Frigidaire washing machine error code E90, it indicates that there is a communication issue between the user control board and the motor board. Here’s how to replace these boards…
1. User Control Board
Follow the steps below to replace the control board in your Frigidaire washing machine…
How To Replace Frigidaire Front Loader Washing Machine User Control Board
Do the following to replace the user control board in your Frigidaire front loader washing machine…
Step 1. Unplug your washing machine from its power source and turn off the water supply before attempting any repairs in order to prevent any chances of electrocution and water leakage.
Step 2. Using a Philips screwdriver, remove the screws at the back of your washing machine holding the top panel. Slide the top panel back and lift it off the washing machine.
Step 3. Pull out the dispenser drawer and press the tab inside to take it out completely. Use your Philips screwdriver to take out the three screws beside the dispenser drawer housing.
Step 4. Use your Philips screwdriver to take out the screws on each side at the back of the control panel. Use a flat-blade screwdriver to pry the clips on the control panel. Detach the panel from the washing machine.
Step 5. Disconnect the electrical connectors attached to the control board (make sure to take note of where each wire goes). Use your screwdriver to take out the screws holding the board to the control panel.
Step 6. Use a flat-blade screwdriver to pry the two halves of the control board. Use a pair of needle-nosed pliers to release the little retainers at the back half of the control holding the connectors.
Step 7. Set the old control board aside. Take your new user control board out of its packaging. Use a flat-blade screwdriver to pry out the little shaft on the old control board. Insert the shaft into the new control board.
Step 8. Use your screwdriver to pry out the indicator pieces and transfer them to the new control board. Pull off the black cover on the indicator screen. Use your flat-blade screwdriver to help pry off the screen from the old control board.
Step 9. Snap the screen onto the new control board and put the black cover in place. Snap the wire connector retainers into the holes at the back of the new control board.
Step 10. Line up the new control board with the control panel (ensure that the knob shaft on the control board goes through the opening on control panel). Use your Philips screwdriver to secure the control board to the panel.
Step 11. Connect each electrical connector to its appropriate terminal on the new control board. Snap the control panel onto the front of your washing machine and apply the screws on each top corner with your Philips screwdriver.
Step 12. Using your Philips screwdriver, apply the three screws beside the detergent drawer housing and slide the drawer back in. Put your washing machine’s top panel back on and apply the screws at the back to secure it.
Step 13. Turn your washing machine’s water supply back on and plug the power cord in. Make sure everything is working as it should by running a wash cycle.
How To Replace Frigidaire Top Loader Washing Machine User Control Board
Here’s what you’ll need to do to replace the user control board in your Frigidaire top loader washing machine…
Step 1. Unplug your washing machine from its power supply and turn off the water supply before starting any repairs on your washing machine. This will prevent any chances of electrocution and water leakage.
Step 2. Insert a small screwdriver into the little holes at the back of the control panel (this will release the clips holding the panel). Disconnect the control panel and lay it on the lid of your washing machine.
Step 3. Disconnect the electrical connectors attached to the control board (make sure to note where each wire goes). Using a Philips screwdriver, take out the screws holding the control board to the panel. Pull the board off and set it aside.
Step 4. Take your new control board out of its packaging and put it in place on the control panel. Apply the screws with your Philips screwdriver to secure the new board. Connect each electrical connector to its appropriate terminal on the new board.
Step 5. Realign the control panel with the housing and snap it in place. Turn on your washing machine’s water supply and plug the power cord back in. Run a wash cycle to make sure everything is working properly.
2. Motor Control Board
In a few cases, the motor control board may be the cause of the E90 error code. Here’s how to replace this part…
How To Replace Frigidaire Front Loader Washing Machine Motor Control Board
Do the following to replace the motor control board in your Frigidaire front loader washing machine…
Step 1. Turn off your washing machine’s water supply and unplug the power cord before attempting any repairs. This will prevent electrocution and water leakage.
Step 2. Use a Philips screwdriver to take out the screws at the back of your washing machine holding the rear panel. Pull the panel off your washing machine and set it aside.
Step 3. Pull the drive belt off the drive pulley and motor shaft, then set it aside. Use a nut driver to take out the nuts holding the drive motor to the tub. Push the motor forwards slightly and lay it on the base of your washing machine.
Step 4. Disconnect the electrical connectors attached to the drive motor. Push the motor out of the way.
Step 5. Use a Philips screwdriver to take out the screw holding the little control board bracket to the base of your washing machine. Pull the motor control board housing forwards a bit.
Step 6. Tilt the control board sideways a bit and disconnect the electrical connectors attached to it. Pull the motor control board out of your washing machine and set it aside.
Step 7. Use your screwdriver to take out the screw holding the mounting bracket to the control board. Take your new washing machine control board out of its packaging. Install the mounting bracket from the old control board on the new board.
Step 8. Put the new control board inside the washing machine and apply the screw to secure the mounting bracket. Pull the drive motor forwards and connect the electrical connectors from the control board to it.
Step 9. Put the motor back in place at the bottom of the tub and apply the mounting nuts to secure it. Run the drive belt back around the drive pulley and the motor shaft.
Step 10. Snap the rear panel of your washing machine back in place and apply the screws to secure it. Plug your washing machine back to its power source and turn on the water supply. Run a wash cycle to make sure the issue has been fixed.
How To Replace Frigidaire Top Loader Washing Machine Motor Control Board
Do the following to replace the motor control board in your Frigidaire top loader washing machine…
Step 1. Make sure to unplug your washing machine from its power source and turn off the water supply before attempting any repairs. This is to prevent any chances of water leakage and electrocution.
Step 2. Use a screwdriver to take out the two screws at the bottom of your washing machine’s front panel. Slide the panel downwards and pull it out.
Step 3. Use your screwdriver to take out the screw holding the motor control board to the base of your washing machine. Disconnect all the electrical connectors attached to the board (make sure to take note of where each connector goes).
Step 4. Pull the old board out of your washing machine and set it aside. Take your new control board out of its packaging. Connect each electrical connector to its appropriate terminal on the new board. Install the new board in your washer and apply the mounting screw to secure.
Step 5. Snap the main front panel of your washing machine back in place and apply the two screws at the bottom to secure it. Plug your washing machine back to its power source and turn on the water supply. Run a wash cycle to make sure everything is working properly.
