Is your LG washing machine making a noise? Don’t worry; we’ve got you covered. In this detailed guide, we’ll be giving you detailed steps to take if your washing machine is making noise.
To carry out these repairs, you’ll need to have some repair skills. You’ll also need different sets of tools. So, without wasting any more time, let’s get right to it…
Table of Contents
LG Washing Machine Making A Noise When Filling With Water — How To Fix
Here are the things that could cause your LG washing machine to make noise when filling with water…
1.Water Pressure Is Too High
Do the following if the water pressure of your LG washing machine is too high…
Step 1. Turn off your washing machine’s power supply.
Step 2. Go to your water supply line.
Step 3. Reduce the water flow by partially closing the valve.
Step 4. Turn on your washing machine’s power supply and resume the cycle to see if the issue has been resolved.
2.Water Inlet Valve Is Defective
Here’s how to replace a defective water inlet valve on your LG washing machine…
How To Replace LG Washing Machine Water Inlet Valve — Front Loaders
Do the following to replace the water inlet valve on your LG front loader washing machine…
Step 1. Turn off your washing machine’s water and power supply in order to avoid water leakage or electrocution.
Step 2. Using a Philips screwdriver, remove the screws at the back of the washing machine holding the top panel.
Step 3. Slide the panel back a few inches and lift it off the washing machine.
Step 4. Disconnect the water inlet hose from the back of your washing machine.
Step 5. The water inlet valve will be mounted inside the washer on the other side of the water inlet port. Disconnect the solenoid wires connected to the water inlet valve (take note of the positioning of each wire).
Step 6. Using a pair of pliers, press the clamps on the hoses connected to the valve and slide them out place.
Step 7. Detach the hoses from the water inlet valve.
Step 8. The water inlet valve is held to the washing machine by two screws next to the water inlet port. Take the screws out using a Philips screwdriver.
Step 9. Pull the water inlet valve out of your washing machine.
Step 10. Get your new water inlet valve out of its pack.
Step 11. Install the new water inlet valve in your washing machine and secure it by applying the two screws at the back.
Step 12. Connect each hose to its appropriate port on the new water inlet valve.
Step 13. Slide the retaining clamps back in place to secure the hoses to the new water inlet valve.
Step 14. Connect each solenoid wire to its appropriate terminal on the new water inlet valve.
Step 15. Ensure that all connections are secure.
Step 16. Put the top panel of your washing machine back on and secure it by applying the screws at the back.
Step 17. Connect your water inlet hose back to the washing machine.
Step 18. Turn on your washing machine’s water and power supply.
Step 19. Run a wash cycle to see if the issue has been resolved.
How To Replace LG Washing Machine Water Inlet Valve — Top Loaders
Do the following to replace the water inlet valve on your LG top loader washing machine…
Step 1. Turn off your washing machine’s water and power supply to avoid water leakage or electrocution.
Step 2. Go to the back of your washing machine.
Step 3. Using a Philips screwdriver, remove the five screws securing the rear panel of the user control board (three at the top and two at the bottom).
Step 4. Detach the panel from the washing machine.
Step 5. Detach the control housing from the washing machine and lay it on the lid of the washer.
Step 6. Disconnect the water inlet hose from the water inlet valve.
Step 7. Disconnect the solenoid wires connected to the water inlet valve (take note of the positioning of each wire).
Step 8. Using a pair of pliers, press and release the retaining clamps holding the hoses to the water inlet valve.
Step 9. Disconnect the hoses from the water inlet valve.
Step 10. Using a Philips screwdriver, remove the three screws holding the water inlet valve to the washing machine.
Step 11. Pull the water inlet valve out of the washing machine.
Step 12. Get your new water inlet valve out of its pack.
Step 13. Install the new water inlet valve in your washing machine and secure it by applying the three screws.
Step 14. Connect the hoses to the new water inlet valve and secure them by sliding the retaining clamps in place.
Step 15. Connect each solenoid wire to its appropriate terminal on the new water inlet valve.
Step 16. Connect the water inlet hose to the new water inlet valve.
Step 17. Reposition the control housing on the washing machine.
Step 18. Put the rear panel of the control housing back on and secure it by applying the five screws.
Step 19. Turn on your washing machine’s water and power supply.
Step 20. Run a wash cycle to see if the issue has been resolved.
Check out these other articles…
LG Washing Machine Error Codes [Solved]
How To Use LG Washing Machine [A Guide]
LG Washing Machine Drum [How To/Issues & Solutions]
LG Washing Machine Stuck [How To Fix]
LG Washing Machine Not Washing Properly [Solution]
LG Washing Machine Grinding Noise — Solved
If your LG washing machine Is producing a grinding sound, you’ll need to replace the tub bearings. Here’s how to do this…
Step 1. Order your new tub bearings online (the bearings set has three parts; Depending on your washer’s model, you may have to purchase each part separately).
Step 2. Turn off your washing machine’s water and power supply to avoid water leakage or electrocution.
Step 3. Go to the back of your washing machine.
Step 4. Using a Philips screwdriver, remove the screws at the back of the washing machine holding the top panel.
Step 5. With the screws removed, slide the panel back a few inches and lift it off the washing machine.
Step 6. Pull out the soap dispenser and press the blue tab at the center to take it out of the washing machine completely.
Step 7. Using a Philips screwdriver, remove the two screws beside the detergent drawer housing.
Step 8. Use a flat-blade screwdriver to release the clips at the back of the user control panel.
Step 9. Detach the user control panel from the front of your washing machine and lay it on top of the cabinet frame.
Step 10. Flip open the filter housing cover at the lower front of your washing machine.
Step 11. Pull out the emergency drain hose and take out the screw beside it with a Philips screwdriver.
Step 12. Pull the lower front panel off the washing machine.
Step 13. Open the door of your washing machine.
Step 14. Wedge a flat-blade screwdriver under the retaining wire around the door seal and work your way around until the entire wire comes off.
Step 15. Push the door seal aside into the drum.
Step 16. Reach inside the washer behind the door lock and disconnect the electrical connector there.
Step 17. Using your Philips screwdriver, remove the five screws holding the main front of your washing machine (two at the top and three at the bottom).
Step 18. Lift the main front up and pull it out of the washing machine.
Step 19. Pull the cross member under the detergent drawer housing out.
Step 20. Lift the detergent drawer housing out of place.
Step 21. Using a pair of pliers, press and release the clamp holding the detergent hose to the tub of the washing machine.
Step 22. Push the detergent housing out of the way and lay it on top of the washer’s cabinet frame.
Step 23. Remove the screws holding the circular weight around the front of the drum using a Philips screwdriver.
Step 24. Get a 13mm socket wrench.
Step 25. Using the socket wrench, remove the bolts holding the weight at the top of the washing machine’s tub.
Step 26. Take a picture of the wire connectors attached to the lower front of the washing machine’s tub (this is the heater element).
Step 27. Disconnect each wire from the heater element.
Step 28. Undo the nut at the center of the heater element and pull the heater element out of the washing machine.
Step 29. Go to the bottom of the washing machine’s tub and remove the screw holding the main drain hose to the tub.
Step 30. Disconnect the drain hose from the washing machine.
Step 31. Using your Philips screwdriver, release the cables that are still connected to your washing machine’s tub.
Step 32. Go to the back of your washing machine.
Step 33. Using your Philips screwdriver, remove the screws securing the rear panel of your washing machine.
Step 34. Lift the rear panel up and pull it out off the washing machine.
Step 35. Using a 19mm socket wrench, remove the bolt at the center of the motor assembly at the back of the washing machine’s tub.
Step 36. Pull the motor assembly out of the washing machine.
Step 37. Switch to a 10mm socket wrench and remove the six bolts securing the drive motor stator to the back of the washer’s tub.
Step 38. Detach the drive motor stator from the back of the washing machine’s tub.
Step 39. Disconnect the electrical connectors of the drive motor stator connected to the drum.
Step 40. Disconnect any other wires connected to the back of the washing machine’s tub.
Step 41. Disconnect the dampers at the base of your washer securing the tub.
Step 42. Remove the springs at the top of the drum connected to the cabinet.
Step 43. Pull the drum out of the washing machine through the front or top of the cabinet frame
Step 44. Using a socket wrench, take out all the bolts holding both halves of the drum together.
Step 45. Use a flat-blade screwdriver to detach the two halves of the drum.
Step 46. Using a mallet, tap the end of the drum shaft to free it from the bearings (use a socket extension as a drift to help push it out).
Step 47. Lay the tub down flat on the ground.
Step 48. Using a screwdriver, pry out the rubber seal from inside the tub.
Step 49. Clean the face of the inner bearing.
Step 50. Apply some penetrating fluid to the inner bearing to make it easier to remove.
Step 51. Turn the tub the other way around.
Step 52. Using the socket extension and mallet, knock the inner bearing out of the washing machine’s tub.
Step 53. Turn the tub over again.
Step 54. Remove the inner bearing from the washer’s tub.
Step 55. Apply some penetrating fluid to lubricate the outer bearing.
Step 56. Using a chisel or flat-blade screwdriver, work the rim of the outer bearing free.
Step 57. Once the outer bearing has been removed, clean the bearing housing.
Step 58. Get your new bearings out of their pack.
Step 59. Knock the new bearings into the housing using your mallet and socket extension. Ensure that pressure is applied evenly on all sides of the bearings.
Step 60. Push the new seal into the bearing housing.
Step 61. Lower the drum into the tub (ensure that the shaft of the drum sits in the bearings).
Step 62. Put the other half of the tub back on and secure the two halves to each other by applying the screws around.
Step 63. Put the tub back in the washing machine’s cabinet frame.
Step 64. Attach the springs to the top of the washer’s tub and hook them to the sides of the cabinet frame.
Step 65. Secure the dampers to the base of the washer’s tub.
Step 66. Reconnect the drain hose and pressure chamber to the base of the washing machine’s tub.
Step 67. Place the weight back on the front of the washing machine and secure it by applying any screws or bolts.
Step 68. Put the weight back at the top of the washing machine’s tub.
Step 69. Put the detergent drawer housing back in place and connect the hose to the washing machine’s tub using the clamp.
Step 70. Put the heater element back in the washing machine and apply the nut at the center.
Step 71. Using the images you took as reference, connect all electrical connectors at the front of your washing machine to their appropriate terminals.
Step 72. Go to the back of your washing machine.
Step 73. Reconnect the motor stator wire connectors as well as any other wires at the back of the washing machine’s tub.
Step 74. Put the drive motor stator back on the tub’s rear and secure it by applying the six 10mm bolts.
Step 75. Put the motor assembly back on top of the motor stator and secure it by applying the screw at the center.
Step 76. Put the rear panel of the washing machine back on and secure it by applying the screws.
Step 77. Go back to the front of your washing machine.
Step 78. Put the main front of your washing machine back on and secure it by applying the five screws (two at the top and three at the bottom).
Step 79. Open the door of your washing machine.
Step 80. Reach in and reconnect the door lock’s electrical connector.
Step 81. Fit the door seal back around the door opening.
Step 82. Fit the retaining band around the door seal (you’ll need a flat-blade screwdriver to do this.
Step 83. Close the door of your washing machine.
Step 84. Put the lower front panel of your washing machine back on and apply the screw beside the emergency drain hose to secure it.
Step 85. Snap the user control panel back in place and secure it by applying the two screws beside the detergent drawer housing.
Step 86. Put the detergent drawer housing back in place.
Step 87. Put the main top of your washing machine back on and secure it by applying the screws at the back.
Step 88. Ensure that all connections are properly secured.
Step 89. Turn on your washing machine’s water and power supply.
Step 90. Run a wash cycle to ensure that everything is working properly.
LG Washing Machine Making Noise When Spinning
If your LG washing machine is making noise when spinning, the following are issues to look for…
1. Loose Or Damaged Weights (Front Loaders)
The weights help keep your front loader washing machine balanced. If the weights are loose or cracked, a lot of noise will be produced during spin cycles. Follow the steps below to replace this part…
Step 1. Ensure that your appliance is disconnected from the power outlet before starting this repair in order to prevent any chances of electrocution.
Step 2. Loosen the bolts at the back of the machine securing the top panel using a Philips screwdriver. Slide the panel backwards a few inches, then lift it off the cabinet.
Step 3. Slide the soap tray out of the dispenser, then press the little tab inside to release it from the housing.
Step 4. Loosen the two bolts next to the dispenser’s opening. Take out the screws at the back of the control panel. Pry the panel off the mounting bracket, then set it on top of the cabinet.
Step 5. Pry the pump filter access panel open, then pull the emergency drain tube out of the retainers. Using your Philips screwdriver, take out the bolts securing the pump filter housing. Pull the housing out and set it it aside.
Step 6. Take out the single screw at the bottom of the front panel. Open the door of your washing machine.
Step 7. Using a flat-blade screwdriver or needle-nosed pliers, carefully pry the retaining wire off the door boot seal (take care not to puncture the seal).
Step 8. Pry the seal off the front panel. Reach into the cabinet, then detach the wire harness from the door lock assembly.
Step 9. Loosen the Philips screws at the top of the front panel. Lift the front panel off the cabinet, then set it aside.
Step 10. Using a 10mm socket wrench, take out the nuts securing the upper and lower weights to the front of the drum. Lift each weight off the drum carefully, then set aside.
Step 11. Prepare the new weights for installation by unpacking them. Carefully mount each weight onto the front of the drum, then secure them by tightening the 10mm bolts.
Step 12. Lift the front panel, then carefully mount it on the cabinet. Tighten the bolts at the top of the front panel using your Philips screwdriver.
Step 13. Apply the single screw at the bottom of the front panel. Push the pump filter housing back into the cabinet, then apply the two screws to secure.
Step 14. Open your washing machine’s door. Reach in behind the front panel, then plug the wire harness back into the door lock assembly.
Step 15. Fit the door gasket around the door opening. With your flat-blade screwdriver, fit the retaining wire around the door seal.
Step 16. Snap the control panel back on the mounting bracket, then apply the Philips screws at the back.
Step 17. Tighten the two screws next to the dispenser. Push the detergent tray back into the housing.
Step 18. Mount the top cover onto the machine, then slide it forwards. Secure the top panel by applying the Philips screws.
Step 19. Plug your appliance back into the power outlet. Turn your washing machine on, then run a spin cycle to ensure that the noise has stopped.
2. Damaged Suspension Rod (Top Loaders)
Follow the steps below to replace damaged suspension rod in your top loader LG washing machine…
Step 1. Disconnect your appliance from the power outlet before starting this repair in order to avoid any chances of electrocution.
Step 2. Insert a putty knife underneath the two front corners of the top panel (this will release the locking clips. Lift the top panel, then support it.
Step 3. Lift the suspension rod you want to replace, then unhook it from the cabinet mount. Unhook the lower portion of the rod from the tub mount.
Step 4. Pull the suspension rod out of the cabinet, then discard it. Prepare the new suspension rod for installation by unpacking it.
Step 5. Slide the lower portion of the new rod through the tub mount. Hook the upper part of the rod onto the cabinet mount.
Step 6. Lower the top panel, then carefully snap it back onto the machine. Reconnect your appliance to the electrical outlet, then try running a spin cycle to ensure that the noise has stopped.
3. Damaged Shock Absorbers
Follow the steps below to replace damaged shock absorbers in your front loader LG washing machine…
Front Shock Absorbers
Replace the front shock absorbers in your LG washing machine by following the steps below…
Step 1. Ensure that your appliance is disconnected from the power outlet before starting this repair in order to prevent any chances of electrocution.
Step 2. Open your washing machine’s door. Using a flat-blade screwdriver or needle-nosed pliers, take the retaining band off the door boot seal (ensure that you don’t damage the seal.
Step 3. Peel the door gasket off the door opening. Reach into the cabinet behind the front panel, then detach the wire harness from the door lock assembly.
Step 4. Open the pump filter access panel at the lower front of the machine. Pull the emergency drain tube out of the retainers.
Step 5. Loosen the nuts securing the pump filter housing using your Philips screwdriver. Pull the filter out of the cabinet and set it aside.
Step 6. Loosen the single bolt at the bottom of the front panel. Go to the back of the machine, then take out the nuts securing the top panel.
Step 7. Pull the top panel backwards a few inches, then lift it off the machine. Slide the soap tray out. Press the little tab in the tray to release it from the dispenser housing.
Step 8. Using your Philips screwdriver, take out the two nuts at the back of the control panel. Loosen the two screws next to the dispenser opening.
Step 9. Pry the control panel off the mounting bracket, then set it on top of the cabinet. Loosen the screws at the top of the front panel.
Step 10. Carefully lift the front panel off the cabinet, then set it aside. Push a 12mm socket onto the pointed end of the upper mounting pin of one of the front shock absorbers. Pull the pin out using pliers.
Step 11. Using the 12mm socket, take out the lower pin in the same way. Pull the shock absorber out of the mounts on the tub and cabinet, then discard it.
Step 12. Prepare your new washing machine shock absorber for installation by unpacking it. Push the shock absorber into the mounts on the tub and cabinet.
Step 13. Push the lower and upper mounting pins into place to secure the new shock absorber. Replace the second front shock absorber by repeating the steps above.
Step 14. Lift the front panel, then remount it on the cabinet. Using your Philips screwdriver, apply the bolts at the top of the front panel.
Step 15. Tighten the single screw at the bottom of the front panel. Push the pump filter housing into the cabinet, then apply the two bolts.
Step 16. Open your machine’s door, then reconnect the wire harness to the door lock assembly. Fit the door boot seal around the front panel.
Step 17. Using a flat-blade screwdriver, fit the outer retaining wire around the door seal. Snap the control panel onto the front of the cabinet.
Step 18. Using your Philips screwdriver, apply the bolts at the back of the front panel. Tighten the two screws next to the dispenser opening.
Step 19. Push the soap tray into the dispenser. Place the top cover on the cabinet, then push it forwards. Tighten the bolts at the back of the panel to secure it.
Step 2. Plug your washing machine’s power cord back into the outlet, then try running a wash cycle to ensure that the noise has stopped.
Rear Shock Absorbers
Replace a rear shock absorber in your front loader LG washing machine by following the steps below…
Step 1. Ensure that your appliance is disconnected from the power outlet before starting this repair in order to prevent any chances of electrocution.
Step 2. Use a Philips screwdriver to take out the nuts securing the rear access panel to the cabinet. Pry the panel off the cabinet and set it aside.
Step 3. Push a 12mm socket onto the pointed end of the upper rear shock absorber mounting pin (this will release the locking tab). Pull the pin out using pliers, then take the lower pin out the same way.
Step 4. Pull the old shock absorber out of the cabinet, then discard it. Prepare your new washing machine shock absorber for installation by unpacking it.
Step 5. Push the lower end of the shock absorber into the mount on the cabinet floor. Push the lower mounting pin into place.
Step 6. Push the upper end of the shock absorber into the port at the bottom off the tub. Secure the shock absorber by pushing the upper mounting pin into place.
Step 7. Snap the rear access panel back onto the machine. Secure the rear panel by tightening the Philips screws.
Step 8. Plug your washing machine into the power outlet, then try running a wash cycle to ensure that the noise has stopped.
4. Damaged Bearings (Front Loaders)
If the drum makes a lot of noise when turned by hand, the bearings have gone bad. The bearings are mounted in the rear half of the outer tub. To replace damaged bearings in your front loader LG washing machine, follow the steps below…
Tools Required:
- Philips screwdriver
- Hammer
- Pliers
- Punch
- Liquid soap
- Two wooden blocks
- 13 and 17mm socket wrenches
- 10mm socket wrench with an extension
- Flat-blade screwdriver
- Penetrating oil
- New bearing kit
Step 1. Prevent any chances of electrocution and leakage by disconnecting your appliance from the power outlet and shutting the water supply taps before starting this repair.
Step 2. Go to the back of the machine, then take out the bolts securing the top cover. Slide the top panel backwards about an inch or so, then lift it off the machine.
Step 3. Slide the soap tray out. Press the little tab in the tray to release it from the dispenser housing. Set the tray aside.
Step 4. With your Philips screwdriver, take out the bolts next to the control panel. Disconnect the wire harnesses from the back of the control panel.
Step 5. Take out the screws at the back of the control panel. Pry the panel off the mounting plate, then set it aside.
Step 6. Open the door of the machine. Wedge a flat-blade screwdriver underneath the retaining wire around the door boot seal. Work the screwdriver around the door carefully until the wire pops off.
Step 7. Peel the rubber gasket off the door opening. Reach behind the front panel, then disconnect the wire harness from the door switch assembly.
Step 8. Pry the pump filter access panel open. Pull the emergency drain tube out of the retainers.
Step 9. Place a small dish under the tube. Pull the cap off the hose, then drain out any water stuck in the machine.
Step 10. Once all the water has been drained out of the machine, put the hose’s cap back on. With your Philips screwdriver, loosen the two screws securing the pump filter housing.
Step 11. Pull the pump filter housing out of the cabinet and set it aside. Using your Philips screwdriver, loosen the single bolt at the bottom of the front panel.
Step 12. Loosen the screws at the top of the front panel. Carefully lift the front panel off the machine and set it aside.
Step 13. Using a flat-blade screwdriver if needed, pry the little tube off the port on the door boot seal.
Step 14. Using a 10mm socket wrench, take out the bolts securing the lower and upper weights to the front of the drum. Carefully lift each weight off the machine and set aside.
Step 15. Loosen the nut on the screw-clamp securing the vent hose to the port at the top of the drum. Detach the hose from the drum.
Step 16. Use your Philips screwdriver to loosen the screw-clamp securing the dispenser hose to the tub. Detach the hose from the machine.
Step 17. Disconnect the heating element wire connectors at the lower front of the drum (ensure that you note where each plug goes). Detach the thermistor wire harness next to the heating element.
Step 18. Go to the back of the cabinet. Using a Philips screwdriver, take out the bolt securing the rear access panel. Pry the panel off the cabinet and set it aside.
Step 19. Loosen the bolt securing the rotor to the back of the tub using your 17mm socket wrench. Pry the rotor off the machine and set it aside (this will require some effort).
Step 20. Detach the pressure tube from the port at the lower rear of the tub. Place a small rag underneath the tub.
Step 21. With your Philips screwdriver, loosen the bolt on the screw-clamp securing the sump hose to the bottom of the tub. Detach the hose from the machine.
Step 22. Use your Philips screwdriver to take out the nut securing the stator grounding wire to the rear of the tub. Loosen the bolts securing the stator’s wire harness retainer to the back of the machine.
Step 23. Use a 10mm socket wrench to take out the nuts securing the stator to the tub shaft. Lift the stator off the tub.
Step 24. Detach the two wires connected to the stator (ensure that you take note of where each plug goes).
Step 25. Push the 13mm socket onto the pointed end of the upper rear shock absorber mounting pin. Pull the pin out using pliers. Detach the shock absorber from the bottom of the tub. Repeat this process with the front shocks.
Step 26. Using a flat-blade screwdriver if needed, pry the suspension spring retainers off the cabinet.
Step 27. Carefully lift the springs, then unhook them from the cabinet. Guide the tub assembly out of the cabinet.
Step 28. Unhook the two springs from the tub. Set the tub assembly on two supports facing upwards.
Step 29. Using your 10mm socket with an extension, take out the bolts securing the two halves of the outer tub together. Lift the front half of the outer tub off the assembly, then set it aside.
Step 30. Turn the tub assembly over so that the rear half of the outer tub rests on the supports. Apply some penetrating oil to the shaft at the back of the tub, then let it sit for a while.
Step 31. Using a mallet, carefully knock the inner tub shaft out of the rear half of the outer tub.
Step 32. Move the inner tub aside. Turn the rear half of the outer tub upright. Pry the bearing seal out of the rear half of the outer tub using a flat-blade screwdriver.
Step 33. Apply some penetrating oil to the bearings in the tub. Using a hammer and a punch, knock the outer bearing out of the tub.
Step 34. Turn the tub assembly over. Use the punch and hammer to knock the inner bearing out of the tub. Using a soft brush, clean the bearing housing thoroughly.
Step 35. Prepare the new bearing kit for installation by unpacking it. Apply some liquid soap to the new bearings.
Step 36. Place the new outer bearing on tub, then knock it into the housing using a hammer (ensure that the bearing sits evenly).
Step 37. Turn the tub over, then use your hammer to knock the new inner bearing into the seat. Apply some soap to the new bearing seal.
Step 38. Firmly push the new seal into place above the inner bearing. Lower the inner tub into the rear half of the outer tub.
Step 39. Inspect the rubber gasket in the groove of the outer tub. If the seal is damaged, you’ll need to replace it.
Step 40. Carefully lower the front half of the outer tub onto the assembly. Secure the two halves of the tub by tightening the 10mm bolts.
Step 41. Attach the two suspension springs to the tub. Lift the tub assembly, then carefully guide it back into the cabinet.
Step 42. Lift the two suspension springs and hook them onto the cabinet. Snap the retaining caps onto the suspension springs.
Step 43. Push each shock absorber into the mount at the bottom of the tub. Secure the shock absorbers by pushing the upper mounting pins into place.
Step 44. Reattach the dispenser hose and vent hose to the port at the top of the drum. Tighten the screw-clamps with your Philips screwdriver to secure the hoses.
Step 45. Reconnect the air pressure tube to the port at the back of the tub. Plug each wire harness into its appropriate terminal on the heating element and thermistor at the lower front of the tub.
Step 46. Reattach the sump hose to the outlet port at the bottom of the tub. Secure the hose by tightening the screw-clamp using your Philips screwdriver.
Step 47. Plug each wire harness into its appropriate terminal on the stator. Place the stator at the back of the tub, then secure it by applying the 10mm bolts.
Step 48. Secure the stator’s grounding wire to the tub by tightening the Philips screw. Apply the nut to secure the wire retainer to the tub.
Step 49. Place the rotor on the stator. Secure the rotor by tightening the 17mm bolt. Snap the rear access panel onto the cabinet, then apply the bolts using your Philips screwdriver.
Step 50. Go to the front of the machine, then mount the weights onto the drum. Secure the weights by tightening the 10mm bolts.
Step 51. Reconnect the little tube to the port at the top of the door boot seal. Lift the front panel, then mount it on the cabinet. Use your Philips screwdriver to apply the bolts at the top of the panel.
Step 52. Tighten the single screw at the bottom of the front panel. Push the pump filter housing into the front panel, then apply the two screws to secure it.
Step 53. Reach into the cabinet behind the front panel, then plug the wire harness into the door switch assembly.
Step 54. Fit the door gasket around the front panel. Using needle-nosed pliers or a flat-blade screwdriver, fit the retaining band around the door opening.
Step 55. Plug the wire connectors back into the control panel. Snap the panel onto the front of the machine. Apply the bolts at the back of the panel using your Philips screwdriver.
Step 56. Tighten the two screws next to the dispenser opening. Slide the detergent tray into the dispenser.
Step 57. Mount the top panel on the cabinet, then push it forwards. Apply the bolts at the back of the panel using your Philips screwdriver.
Step 58. Plug your washing machine into the power outlet, then turn the water valves on. To ensure that the noise has stopped, try running a wash cycle.
5. Damaged Clutch (Top Loaders)
The clutch assembly is at the bottom of your top loader washing machine. If the clutch gets damaged, it will cause the machine to make noise when spinning. For detailed steps on how to replace this part, read this article: LG Washing Machine Spin.
6. Damaged Motor Bearing
If your LG washing machine uses a drive motor, you should check the bearing if you’re hearing noises. Follow the steps below to check this part…
Front Loaders
Check the drive motor bearing in your front loader LG washing machine…
Step 1. Ensure that your appliance is disconnected from the power outlet before starting this procedure in order to prevent electrocution.
Step 2. With a Philips screwdriver, take out the bolts securing the rear panel to the machine. Pry the access panel off the cabinet and set it aside.
Step 3. Unhook the drive belt from the motor pulley and drive pulley at the back of the machine.
Step 4. Disconnect the wire harness attached to the drive motor, then release the wires from the retainer.
Step 5. Use a 13mm socket wrench to take out the bolts securing the drive motor to the bottom of the tub. Lift the motor off the tub carefully, then pull it out of the cabinet.
Step 6. Try rotating the motor shaft by hand. If you notice a grinding noise when turning the motor shaft, it indicates that the bearing has gone bad; you’ll need to replace the motor.
Step 7. Once you’ve gotten the new motor, mount it at the bottom of the tub, then tighten the bolts to secure it.
Step 8. Plug the wire harnesses into the new motor, then secure the wires in the retainer. With the grooved side turned inwards, loop the drive belt around the motor pulley and drive pulley.
Step 9. Snap the rear cover onto the cabinet, then apply the Philips screws to secure it. Plug your washer’s power cord back into the outlet, then try running a spin cycle to ensure that the noise has stopped.
Dryers
Inspect the motor bearing in your LG dryer by following the steps below…
Step 1. In order to prevent any chances of electrocution, ensure that you disconnect the power cord from the outlet before starting this repair.
Step 2. Take out the screws at the back of the machine securing the top panel using a Philips screwdriver. Slide the panel backwards about an inch or so, then lift it off the machine.
Step 3. Use your screwdriver to take out the nuts at the back of the control panel. Pry the panel off the mounting bracket.
Step 4. Disconnect the wires connected to the control panel, then set the panel aside. Open the dryer door, then loosen the two screws at the bottom of the opening.
Step 5. Take out the screws at the top of the front panel. Lift the panel off the machine. Detach the door switch wire harness attached to the front panel, then set the panel aside.
Step 6. Loosen the nuts securing the control panel’s mounting bracket to the front of the machine. Release the wires from the retainer on the bracket, then set the bracket aside.
Step 7. Disconnect the wires from the light assembly at the top of the front bulkhead. Disconnect the moisture sensor connector at the bottom of the bulkhead.
Step 8. Loosen the nuts securing the bulkhead to the cabinet. Carefully lift the bulkhead, then detach it from the cabinet.
Step 9. Reach underneath the drum, then push the idler pulley inwards to release the tension on the belt. Unhook the belt from the motor pulley and idler pulley.
Step 10. Lift the drive belt and drum out of the cabinet carefully, then set them aside. Take out the nuts securing the cover to the blower wheel. Take the cover off and set it aside.
Step 11. Disconnect the wire harness connected to the drive motor. Secure the motor shaft using a wrench. Loosen the bolt securing the blower wheel to the shaft using a 14mm socket.
Step 12. Pull the wheel out of the housing, then set it aside. Using a flat-blade screwdriver, pry off the two retaining clips securing the motor assembly. Carefully pull the motor out of the cabinet.
Step 13. Try turning the motor pulley by hand. If the motor makes a lot of noise when turning the pulley, it indicates that the bearing is bad; the motor will need to be replaced.
Step 14. Once you’ve gotten the new motor, install it in the cabinet. Snap the two retaining clips onto the motor.
Step 15. Plug the wire harness into the motor. Place the blower wheel on the motor shaft, then tighten the 14mm bolt to secure it.
Step 16. Place the cover on the blower wheel, then tighten the nuts using a Philips screwdriver.
Step 17. Lift the belt and drum, then guide them into the cabinet carefully. Reach under the drum, then loop the belt around the motor pulley and idler pulley in a zig-zag formation.
Step 18. Mount the front bulkhead on the cabinet, then tighten the screws. Place the control panel’s mounting bracket on the cabinet, then tighten the nuts.
Step 19. Plug the moisture sensor and light assembly wires back in. Lift the front panel, then plug the door switch wire connector back in.
Step 20. Mount the front panel on the cabinet. Using your Philips screwdriver, apply the bolts at the top of the panel.
Step 21. Open the door of the dryer, then tighten the two screws at the bottom. Plug the wire connectors back into the control panel.
Step 22. Snap the control panel onto the mounting bracket, then apply the bolts at the back using a Philips screwdriver.
Step 23. Place the top panel on the cabinet, then push it forwards. Secure the panel by applying the bolts at the back.
Step 24. Plug your washing machine into the power outlet, then try running a cycle to ensure that the noise has stopped.
7. Damaged Drum Rollers (Dryers)
To replace damaged drum rollers in your LG dryer, follow the steps below…
Front Rollers
Replace a front drum roller in your LG dryer by following the steps below…
Step 1. In order to prevent any chances of electrocution, ensure that your appliance is disconnected from the power outlet before starting this repair.
Step 2. Go to the back of the cabinet, then take out the bolts securing the top panel using a Philips screwdriver.
Step 3. Slide the top panel backwards about an inch or so, then lift it off the cabinet. With your Philips screwdriver, take out the nuts at the back of the control panel.
Step 4. Pry the control panel off the mounting bracket. Detach the two wires connected to the control panel, then set the panel aside.
Step 5. Open the door of your machine, then use your Philips screwdriver to loosen the nuts at the bottom of the opening.
Step 6. Take out the bolts at the top of the front panel. Lift the front panel off the cabinet. Detach the wire harness attached to the door switch on the front panel.
Step 7. Loosen the screws securing the control panel’s mounting bracket. Pull the bracket out of place, then set it on top of the cabinet.
Step 8. Disconnect the wires from the light assembly at the top of the front bulkhead. Disconnect the moisture sensor connector at the bottom of the bulkhead.
Step 9. With your Philips screwdriver, loosen the nuts securing the bulkhead to the cabinet. Carefully lift the bulkhead off the cabinet, then set it face-down on the floor.
Step 10. Pull the lint filter out of the bulkhead. Turn the bulkhead over, then loosen the nuts securing the duct. Take the duct off the bulkhead.
Step 11. Turn the bulkhead over again. Secure the rear bolt of the roller you want to replace using a 14mm wrench. Take out the bolt at the front of the roller using a 10mm socket.
Step 12. Slide the roller off the bulkhead, then discard it. Prepare the new roller assembly for installation by unpacking it.
Step 13. Place the new roller on the bulkhead, then secure it by applying the 10mm bolt. Turn the bulkhead over.
Step 14. Mount the duct on the bulkhead, then secure it by applying the Philips screws. Slide the lint filter into the bulkhead.
Step 15. Carefully snap the front bulkhead onto the cabinet, then apply the bolts with your screwdriver.
Step 16. Plug the moisture sensor and drum light connectors back in. Place the control panel’s mounting bracket on the cabinet, then apply the bolts using your Philips screwdriver.
Step 17. Lift the front panel, then plug the wire harness back into the door switch. Mount the front panel on the cabinet, then apply the screws at the top with your Philips screwdriver.
Step 18. Open the dryer’s door, then tighten the nuts at the bottom of the opening. Plug each wire harness back into the control panel.
Step 19. Snap the control panel onto the cabinet, then apply the bolts at the back with your Philips screwdriver.
Step 20. Mount the top panel on the cabinet, then push it forwards. Secure the panel by apply the Philips screws.
Step 21. Plug your dryer into the power outlet, then try running a spin cycle to ensure that the noise has stopped.
Rear Rollers
Replace the rear rollers in your LG dryer by following the steps below…
Step 1. In order to prevent electrocution, ensure that you disconnect your machine from the outlet before starting this repair.
Step 2. Use a Philips screwdriver, take out the bolts at the back of the top panel. Slide the panel backwards about an inch or so, then lift it off the machine.
Step 3. Unscrew the nuts at the back of the control panel. Pry the panel off the front of the machine (use a flat-blade screwdriver if needed).
Step 4. Note the wires attached to the control panel, then disconnect each one. Open the door of the dryer, then loosen the two screws at the bottom of the door opening.
Step 5. Take out the nuts securing the top of the front panel. Lift the panel off the dryer carefully. Detach the wire connector plugged into the door switch on the front panel.
Step 6. Set the front panel aside. Take out the bolt holding the control panel’s mounting bracket. Move the mounting bracket aside.
Step 7. Disconnect the wires from the moisture sensor and drum light on the front bulkhead.
Step 8. Loosen the bolts securing the bulkhead to the cabinet using a Philips screwdriver. Lift the bulkhead off the machine, then set it aside.
Step 9. Reach underneath the drum carefully, then push the idler pulley inwards (this releases the tension on the drive belt).
Step 10. Unhook the drive belt from the motor pulley and idler pulley. Lift the belt and drum out of the cabinet carefully, then set them aside.
Step 11. Secure the bolt at the back of the roller you want to replace using a 14mm wrench. Loosen the nut at the front of the roller using a 10mm socket.
Step 12. Pull the roller off the rear bulkhead, then discard it. Prepare the new drum roller for installation by unpacking it.
Step 13. Mount the new roller on the rear bulkhead, then tighten the 10mm bolt to secure it.
Step 14. Guide the drive belt and drum back into the cabinet. Reach under the drum, then hook the belt onto two pulleys in a zig-zag formation.
Step 15. Rotate the drum by hand slowly to ensure that the belt is properly aligned. Mount the front bulkhead onto the cabinet. Secure the bulkhead by tightening the nuts.
Step 16. Place the control panel’s mounting bracket on the machine, then apply the Philips screws.
Step 17. Reconnect the moisture sensor and drum light wire connectors. Plug the door switch wire harness back into the front panel.
Step 18. Snap the front panel onto the cabinet, then secure it by tightening the nuts at the top.
Step 19. Open the door of the machine, then tighten the two screws at the bottom. Plug the connectors back into the control panel.
Step 20. Snap the panel onto the mounting bracket. Tighten the bolts at the back of the panel.
Step 21. Mount the top cover on the cabinet, then apply the Philips screws at the rear of the machine.
Step 22. Reconnect your appliance to the power outlet, then ensure that the noise has stopped by running a spin cycle.
8. Damaged Suspension Spring (Front Loaders)
The suspension springs hold the tub and help keep it balanced. If one of the springs gets worn out or damaged, the drum will make a lot of noise when spinning. Follow the steps below to replace this part…
Step 1. Ensure that you disconnect your appliance from the power outlet before starting this repair.
Step 2. With someone assisting you, move your washing machine forwards a bit to gain access to the back of the cabinet.
Step 3. Loosen the bolts securing the top panel using a Philips screwdriver. Slide the panel backwards a few inches, then lift it off the machine.
Step 4. Using a screwdriver, loosen the nut on the screw-clamp securing the dispenser outlet hose to the tub. Detach the hose from the machine (some water may spill).
Step 5. Using a flat-blade screwdriver, pry retaining cap off the suspension spring. Lift the spring off the cabinet, then carefully lower the tub.
Step 6. Unhook the spring from the tub, then discard it. Hook your new spring onto the tub mount.
Step 7. Lift the new spring, then carefully hook it onto the cabinet. Snap the retainer onto the new spring. Take out the second spring by repeating the steps above.
Step 8. Reconnect the dispenser outlet hose to the port on the tub. Secure the hose by tightening the screw-clamp.
Step 9. Place the top panel on the cabinet, then apply the bolts at the back using a Philips screwdriver.
Step 10. Plug your washing machine back into the power outlet. To ensure that the noise is gone, try running a spin cycle.
LG Washing Machine Drain Pump Making Noise — Solved
If your LG washing machine drain pump is making noise, you’ll need to replace it. Here’s how to do this…
How To Replace LG Washing Machine Drain Pump — Front Loaders
To replace your LG front loader washing machine drain pump, here’s what you need to do…
Step 1. Turn off your washing machine’s water and power supply in order to avoid water leakage and electrocution.
Step 2. Using a Philips screwdriver, take out the screws at the back of your washing machine holding the top panel.
Step 3. Slide the panel back about a few inches and lift it off the washing machine.
Step 4. Pull the soap dispenser out press the blue tab in the middle to take it out of the washing machine completely.
Step 5. Using a Philips screwdriver, remove the screws on each side of the detergent drawer housing.
Step 6. Using a flat-blade screwdriver, release the tabs at the back of the washing machine’s user control panel.
Step 7. Pull the user control panel off the washing machine and lay it on top of the cabinet frame..
Step 8. Flip open the filter cover at the lower front of your washing machine.
Step 9. Pull out the emergency drain hose and remove the screw next to it with a Philips screwdriver.
Step 10. Pull the lower front panel off your washing machine.
Step 11. Open the door of your washing machine.
Step 12. Wedge a flat-blade screwdriver under the retaining wire around the door seal and work your way around until the entire thing comes off.
Step 13. Push the door seal into the washing machine’s drum.
Step 14. Reach in behind the door lock and disconnect the electrical connector.
Step 15. Close the door of your washing machine.
Step 16. Using a Philips screwdriver, remove the five screws holding the main front of the washing machine (two at the top and three at the bottom).
Step 17. Pull the main front up and out of the washing machine.
Step 18. Using your Philips screwdriver, remove the three screws around the drain filter knob.
Step 19. Take a picture of the orientation of the drain pump before disconnecting anything.
Step 20. Disconnect the electrical connector attached to the drain pump.
Step 21. Using a pair of pliers, press the clamps on the hoses connected to the drain pump and slide them out of place.
Step 22. Disconnect each hose from the drain pump.
Step 23. Pull the drain pump assembly out of the washing machine.
Step 24. Get your new drain pump out of its pack.
Step 25. Install your new drain pump assembly in the washing machine and attach the electrical connector to it.
Step 26. Connect each hose to its appropriate port on the new drain pump assembly, using the pictures you took to guide you.
Step 27. Secure the hoses to the drain pump by sliding the retaining clamps in place.
Step 28. Pass the emergency drain hose of the new drain pump through the opening on the washing machine.
Step 29. Apply the three screws around the drain filter knob.
Step 30. Put the main front of the washing machine back on and secure it by applying the five screws (two at the top and three at the bottom).
Step 31. Open the door of your washing machine.
Step 32. Reach inside the washer and reconnect the door lock’s wire connector.
Step 33. Fit the door seal back around the door opening.
Step 34. Fit the retaining band back around the door seal using a flat-blade screwdriver.
Step 35. Close the door of your washing machine.
Step 36. Put the lower front panel of your washing machine back in place and secure it by applying the screw beside the emergency drain hose.
Step 37. Flip the filter housing cover back up.
Step 38. Snap the user control board back in place and secure it by applying the screws beside the detergent drawer housing.
Step 39. Put the detergent drawer back into the washing machine.
Step 40. Put the top panel of the washing machine back on and secure it by applying the screws at the back.
Step 41. Turn on your washing machine’s water and power supply.
Step 42. Try running a wash cycle to see if the issue has been resolved.
How To Replace LG Washing Machine Drain Pump — Top Loaders
Here’s how to replace the drain pump on your LG top loader washing machine…
Step 1. Turn off your washing machine’s water and power supply in order to avoid water leakage or electrocution.
Step 2. Go to the back of your washing machine.
Step 3. Using a Philips screwdriver, take out the screws holding the rear panel of your washing machine.
Step 4. Release the retaining clamp on each hose connected to the drain pump and slide clamps out of place.
Step 5. Disconnect each hose from the drain pump.
Step 6. Use a 10mm socket wrench to remove the bolts securing the drain pump assembly to the base of your washing machine.
Step 7. Detach the drain pump electrical connector on the base of the washing machine.
Step 8. Pull the wire sleeve from the tabs on the base of your washing machine.
Step 9. Untwist the retaining wire holding the bundle of wire connectors to the frame of your washing machine.
Step 10. To fully release the drain pump assembly from the washing machine, disconnect the two wire pump wire connectors in the wire bundle.
Step 11. Get your new washing machine drain pump assembly out of its pack.
Step 12. Install the new drain pump in your washing machine and secure it by applying the 10mm bolts on the base.
Step 13. Connect the two wire connectors of the new drain pump to the wire bundle
Step 14. Secure the bundle of electrical connectors to the washer’s frame using the retaining wire.
Step 15. Secure the wire sleeve in the tabs on the base of the washing machine.
Step 16. Connect the main wire connector to the drain pump.
Step 17. Connect the two hoses to the new drain pump.
Step 18. Secure the hoses to the pump by sliding the retaining clamps in place.
Step 19. Put the rear panel of the washing machine back on and secure it by reapplying the screws at the back.
Step 20. Turn on your washing machine’s water and power supply.
Step 21. Run a wash cycle to see if the problem has been fixed.
