If you are experiencing problems with your Amana washing machine cycles, this detailed guide will provide steps on how to fix them…
Table of Contents
Amana Washing Machine Stops Mid-Cycle — Solved
If your Amana washing machine stops mid-cycle, it indicates that something is preventing the system from draining. Here’s what you’ll need to do to fix drainage problems in your Amana washing machine…
1. Clean Pump Filter (Only Front Loaders)
Do the following to clean the pump filter in your Amana front loader washing machine…
Step 1. Turn off the power supply to your machine before starting this repair in order to avoid electrocution.
Step 2. Open your machine’s lower front access panel. Place a rag on the floor in front of your machine.
Step 3. Pull the emergency drain hose out of the retainer and place a container under it. Pull the cap off the hose and let any water stuck in the machine drain out completely.
Step 4. Once all the water has drained out, put the hose’s cap back on. Turn the drain pump filter knob and pull it out (some water will spill out).
Step 5. Take the drain pump filter to a sink and clean out any debris and lint clogging it. Once you’ve cleaned the filter properly, put it back in the machine.
Step 6. Snap the access panel back onto the machine. Plug your washer into the power outlet and try running a wash cycle to see if the problem has been fixed.
2. Defective Drain Pump Assembly
Here are the steps you’ll need to take to replace the pump assembly in your Amana washing machine…
How To Replace Damaged Pump Assembly In Amana Top Loader Washing Machine
Do the following to replace your Amana top loader washing machine’s drain pump…
Step 1. Shut your machine’s water supply and disconnect the power cord from the outlet before starting this repair in order to avoid water leakage and electrocution.
Step 2. Spread a towel on the floor underneath the water supply hoses to catch any water leaks. Use a pair of pliers to disconnect the two water supply lines from the ports on your machine.
Step 3. Squeeze the spring clamp on the drain hose and slide it out of place. Pull the drain hose off your machine.
Step 4. Put some tape over the lid of your washing machine to secure it. With the help of another person, tilt the machine backwards carefully and lay it on the floor.
Step 5. Squeeze the spring clamp on the outlet hose connected to the drain pump and slide it out of place. Pull the hose off the pump (keep a rag nearby to clean up any water spillage).
Step 6. Unplug the wire connector from the pump assembly. With a 5/16 inch nut-driver, take out the mounting bolts holding the pump to the bottom of the tub.
Step 7. Carefully pull the drain pump off the tub and set it aside. Take your new washing machine drain pump assembly out of its packaging.
Step 8. Mount the new pump assembly at the bottom of the machine and apply the nuts with your nut-driver. Plug the wire connector to the terminal on the new pump.
Step 9. Connect the outlet hose to the port on the new drain pump and slide the retaining clamp in place to secure it.
Step 10. Carefully set the washing machine back onto its feet and peel the tape off the lid. Reattach the drain hose to the back of the machine and secure it using the spring clamp.
Step 11. Reconnect the HOT and COLD water supply hoses the ports on your machine. Turn the water supply back on and plug the power cord into the outlet. To ensure that the issue has been fixed, try running a wash cycle.
How To Replace Damaged Pump Assembly In Amana Front Loader Washing Machine
Take the following steps to replace your Amana front loader washing machine’s drain pump…
Step 1. Disconnect your washing machine from its power supply before starting this repair in order to prevent electrocution.
Step 2. Using a 1/4 inch nut-driver, take out the bolts at the back of your machine holding the rear panel. Lift the panel off the cabinet and set it aside.
Step 3. Unplug the wire harness from the drain pump. Release the squeeze clamp on the hose attached to the drain pump and slide it out of place. Pull the hose off the pump (some water will spill out).
Step 4. Use a nut-driver to remove the nuts holding the pump to the bottom of the tub. Carefully take the pump out of your machine and set it aside.
Step 5. Remove your new washing machine drain pump from its packaging. Mount the new pump at the bottom of the machine and use your nut-driver to apply the bolts to secure it.
Step 6. Plug the wire connector to the new drain pump. Connect the outlet hose to the port on the new pump and secure it with the retaining clamp.
Step 7. Put the rear access panel back onto the cabinet and apply the screws with your nut-driver.
Step 8. Plug your machine back into its power supply and try running a wash cycle to make sure everything works properly.
Check out these other articles…
Amana Washing Machine Error Codes [Proven Solutions]
Amana Washing Machine Not Draining/Won’t Stop Draining [Solutions]
Admiral Washing Machine Lid [Issues & Solutions]
Amana Washing Machine Sensing [Issues & Proven Solutions]
Amana Washing Machine Leaking [How To Fix]
Amana Washing Machine Stuck On Rinse Cycle — How To Fix
If your Amana washing machine is stuck on a rinse cycle, here are the issues to look for…
1. Blocked Inlet Filters
Your washing machine will not progress past the rinse cycle if the drum hasn’t filled with water. Sometimes a clogged inlet filter is the cause of this issue. Clean the inlet filters in your Amana washing machine by doing the following
Step 1. Disconnect your washing machine from its power supply and turn the water valve off in order to prevent water leaks or electrocution.
Step 2. With a pair of pliers, unscrew the two water supply hoses from the ports at the back of your washing machine (ensure that you have a rag nearby to clean any water leaks).
Step 3. Using a pair of needle-nosed pliers, pull out the little mesh filters inside the water inlet ports at the back of your machine.
Step 4. Take the filters to a sink and rinse out any dirt that may be clogging them. Once you’ve properly cleaned the filters, put them back into the ports.
Step 5. Reconnect the water supply lines to the ports. Turn the water and power supply back on and test the machine by running a rinse cycle.
2. Defective Water Pressure Switch
Replace a defective water level sensor in your Amana washing machine by doing the following…
How To Change Damaged Pressure Sensor In Amana Front Loader Washing Machine
Take the following steps to replace a failed water pressure sensor in your front loader Amana washing machine…
Step 1. Unplug your machine from its power outlet before starting this repair in order to avoid electrocution.
Step 2. Take out the nuts at the back of the machine holding the top panel. Slide the panel backwards about an inch or so and lift it off the cabinet.
Step 3. Unplug the wire connector from the pressure sensor on the cabinet. Pull the tube off the sensor.
Step 4. Use a flat-blade screwdriver to pry the water level sensor off the cabinet and set it aside.
Step 5. Take your new washing machine water level sensor out of its packaging. Plug the wire connector to the new sensor and connect the air pressure tube.
Step 6. Snap the new sensor into the cabinet. Put the top panel onto the machine and apply the bolts with your nut-driver to secure it.
How To Change Damaged Pressure Sensor In Amana Top Loader Washing Machine
Here’s how to replace a failed water pressure sensor in your Amana top loader washing machine…
Step 1. Disconnect your washing machine from the power supply before starting this repair in order to prevent electrocution.
Step 2. Insert a putty knife underneath the control panel (this will release the two retaining clips). Lift the control panel and set it on the cabinet.
Step 3. Pull the tube off the water level sensor. Unplug the electrical connector attached to the water level sensor.
Step 4. Pry the sensor off the control panel using a flat-blade screwdriver and set the sensor aside.
Step 5. Take your new washing machine sensor out of its packaging. Snap the new sensor onto the control panel and plug the wire connector to it.
Step 6. Connect the air pressure tube to the new sensor. Lift the control panel and snap it back into the cabinet. Turn your machine’s power supply back on and make sure the issue has been fixed by running a wash cycle.
3. Faulty Water Inlet Valve
Replace a faulty water inlet valve in your Amana washing machine by doing the following…
Replacing Damaged Inlet Valve In Amana Top Loader Washing Machine
To replace the water inlet valve in your top loader Amana washing machine, here’s what you’ll need to do…
Step 1. Unplug your machine from its power supply and turn the water valve off before starting this repair.
Step 2. Disconnect the COLD and HOT water inlet hoses from the ports at the back of your machine (spread a rag underneath the hoses to catch any water leaks).
Step 3. Insert a tool such as a putty knife underneath the two bottom corners of the control panel (this will release the two spring clips). Lift the control panel and set it on top of the cabinet.
Step 4. Unplug the wire connector of the inlet valve from the control board. Release the squeeze clamp on the hose attached to the valve assembly and slide it out of place. Pull the hose off the valve.
Step 5. With a Philips screwdriver, remove the screws holding the water inlet valve to the cabinet. Pull the valve out of the machine and set it aside.
Step 6. Take your new inlet valve assembly out of its packaging. Mount the new valve in the cabinet and apply the screws with your Philips screwdriver to secure it.
Step 7. Plug the new valve’s wire connector into the control board. Attach the tube to the port on the new valve and secure it with the retaining clamp.
Step 8. Lift the control panel and snap it back into place. Reconnect the two water supply lines to the ports at the back of your machine (in order to prevent water leaks, make sure to secure the hoses properly).
Step 9. Connect your machine back to its power outlet and turn the water valve back on. Try running a rinse cycle to see if the problem has been fixed.
Replacing Damaged Inlet Valve In Amana Front Loader Washing Machine
Replace a damaged inlet valve in your Amana front loader washing machine by doing the following…
Step 1. Shut your washing machine’s water supply and disconnect the power cord from the outlet before starting this repair in order to avoid water leaks or electrocution.
Step 2. With a 1/4 inch nut-driver, take out the screws at the back of your machine holding the top panel. Slide the panel backwards a few inches and lift it off the cabinet.
Step 3. Spread a towel on the floor underneath the water supply lines to clean any water spillage. Using your pliers, unscrew the two water supply hoses from the ports at the back of your machine.
Step 4. Unplug the two wire harnesses attached to the water inlet valve. Release the spring clamp on the tube connected to the valve and pull the hose off.
Step 5. With a Philips screwdriver, take out the screws holding the inlet valve to the cabinet. Pull the valve out of the machine and set it aside.
Step 6. Get your new inlet valve assembly out of its packaging. Plug each wire connector to its appropriate terminal on the new inlet valve.
Step 7. Connect the tube to the new valve and secure it with the spring clamp. Mount the new water inlet valve on the cabinet and apply the screws with your Philips screwdriver.
Step 8. Put the top panel back on the cabinet and use your 1/4 inch nut-driver to apply the mounting nuts.
Step 9. Reattach the COLD and HOT water inlet hoses to the ports at the back of your washing machine (make sure to secure the hoses properly so water can’t leak out).
Step 10. Turn your machine’s water supply back on and plug the power cord into the outlet. Test the washer by running a spin cycle.
4. Failed Control Board
To replace a failed control board in your Amana washing machine, here’s what you’ll need to do…
Changing A Failed Control Board In Front Loader Amana Washing Machine
Take the following steps to replace a failed control board in your Amana front loader washing machine…
Step 1. Unplug your washing machine from its power supply in order to avoid electrocution.
Step 2. Take out the screws holding the top panel with a 1/4 inch nut-driver. Lift the panel off the cabinet and set it aside.
Step 3. Pry the cap off the control board on the cabinet. Unplug each wire connector from the terminals on the control board (ensure that you note where each connector goes).
Step 4. Release the control board wires from the retainers. Pry the control board off the cabinet with a flat-blade screwdriver.
Step 5. Take your new control board assembly out of its packaging and snap it into the cabinet. Plug each wire connector into its appropriate terminal on the new board. Secure the wires in the retainer.
Step 6. Slide the top panel back onto the cabinet and use your nut-driver to apply the screws. Plug your machine back into the power outlet and try running a wash cycle to make sure the issue has been fixed.
Changing A Failed Control Board In Top Loader Amana Washing Machine
Replace a failed control board in your Amana top loader washing machine by doing the following…
Step 1. Disconnect your washing machine from its power supply before starting this repair in order to prevent electrocution.
Step 2. Insert a putty knife under your washer’s control panel (this will release the two spring clips). Set the control panel on top of the cabinet.
Step 3. Unplug each wire harness from the control board (make sure to note where each connector goes before disconnecting anything). Pull the air pressure hose off the board.
Step 4. Use a Philips screwdriver to remove the screws securing the board to the panel. Lift the control board off the panel (the selector knob will fall off).
Step 5. Take your new control board out of its packaging and place it on the control panel. Apply the screws with your Philips screwdriver.
Step 6. Lift the control panel and snap the selector knob onto the shaft. Plug each wire harness into its appropriate terminal on the new control board. Connect the air pressure tube to the port on the board
Step 7. Lift the control panel and snap it back into the cabinet. Turn your machine’s power supply back on and run a wash cycle to make sure the problem has been fixed.
Amana Washing Machine Spin Cycle Not Working — How To Fix
If your Amana washing machine spin cycle isn’t working, here are the issues you should look for…
1. Damaged Drive Belt
Here’s what you’ll need to do to replace your Amana washing machine’s drive belt…
Replacing Failed Drive Belt In Amana Front Loader Washing Machine
Do the following to replace the drive belt in your Amana front loader washing machine…
Step 1. Turn off your machine’s power supply before starting in order to prevent electrocution.
Step 2. Remove the nuts at the back of the machine holding the rear access panel. Lift the panel off the cabinet and set aside.
Step 3. If still intact, pull the drive belt off the motor pulley and drive pulley. Take your new belt of its packaging.
Step 4. Loop the new drive belt around the two pulleys (make sure the grooved side of the belt faces inwards).
Step 5. Put the rear panel back onto the cabinet and apply the screws with your 1/4 inch nut-driver.
Step 6. Turn your machine’s water supply back on and try running a spin cycle to see if the problem has been fixed.
Replacing Failed Drive Belt In Amana Top Loader Washing Machine
Take the following steps to replace the drive belt in your Amana top loader washing machine…
Step 1. Shut the water supply to your washing machine and disconnect the power cord from the outlet in order to avoid water leaks and electrocution.
Step 2. Release the spring clamp from the drain hose at the back of your machine. Pull the hose off the machine.
Step 3. Secure the lid of your machine by putting some tape on it. Use a pair of pliers to unscrew the two water supply lines from the ports at the back of your machine (make sure to keep a rag nearby to clean any water leaks).
Step 4. With the help of another person, carefully tilt the machine backwards and lay it on the floor.
Step 5. Use your nut-driver to take out the screws holding the belt guard. If still intact, take the drive belt of the two pulleys.
Step 6. Remove your new drive belt from its packaging and loop it around the motor pulley and transmission pulley (make sure the grooved side of the belt faces inwards). Put the belt guard back on and apply the screws with your nut-driver.
Step 7. Carefully lift your washing machine back onto its feet and peel the tape off the lid.
Step 8. Connect the drain hose back to the port at the back of the cabinet and secure it with the spring clamp.
Step 9. Reattach the two water supply lines to the ports on your washer (ensure that the hoses are secured properly so water won’t leak).
Step 10. Turn the power supply back on and open the water supply valve. Test the machine by running a spin cycle.
2. Door Isn’t Properly Locked
Many washing machines will not be able to start a cycle unless the door is locked. Ensure that you firmly shut your machine’s door before starting a spin cycle. If your washing machine’s door doesn’t lock, you’ll need to change the lock assembly. Here’s how to do this…
Replacing Failed Amana Front Loader Washing Machine Door Lock
Replace a failed door lock in your front loader Amana washing machine by doing the following…
Step 1. Disconnect your machine’s power cord from the outlet in order to prevent electrocution.
Step 2. Open your machine’s door. Using either a flat-blade screwdriver or a pair of needle-nosed pliers, take out the retaining band around the door boot seal (make sure not to damage the seal).
Step 3. Peel the door seal away from the door lock. Remove all the screws holding the door lock to the cabinet using a Philips screwdriver. Reach inside the machine and pull the lock out.
Step 4. Unplug the wire connector from the door lock and set the door lock aside. Take your new door lock out of its packaging and plug the wire connector to it.
Step 5. Put the new lock back into the machine and secure it by apply the screws. Fit the door gasket back around the door opening.
Step 6. Use your pliers or screwdriver to fit the retaining wire back around the door boot seal).
Step 7. Close your washer’s door, plug the power cord back into the outlet, and try running a spin cycle to see if the issue has been resolved.
Replacing Failed Amana Top Loader Washing Machine Door Lock
Change a damaged lid lock in your top loader Amana washing machine by doing the following…
Step 1. Shut the water supply to your washer and unplug the power cord from the power supply in order to prevent damage.
Step 2. Secure the lid of your washing machine by putting some tape over it. Place a rag on the floor under the inlet hoses.
Step 3. Unscrew the two water supply lines from the ports on your machine (water will spill out).
Step 4. Using your 1/4 inch nut-driver, take out the nuts holding the rear access cover off the control panel. Take the cover off and set it aside.
Step 5. Unplug the lid lock wire connector from the control board and release the wire from the retainer.
Step 6. Use your nut driver to take out the screws holding the top panel. Lift the panel upwards and support it.
Step 7. Pull the lid lock connector through the opening on the top panel. Release the wire from the retainers under the top panel using a flat-blade screwdriver.
Step 8. Remove the screws holding the lid lock using a Philips screwdriver. Take the lock assembly off the top panel and set it aside.
Step 9. Remove your new washing machine lid lock from its packaging. Mount the new lid lock on the top panel and use the mounting screws to secure it.
Step 10. Secure the lid lock wire in the retainers and pass the connector through the opening on the top panel.
Step 11. Lower the top panel and snap it back in place. Go to the back of the machine and plug the wire connector of the new lid lock to the control board.
Step 12. Put the control panel rear access cover back on and apply the nuts with your nut-driver.
Step 13. Apply the bolts to secure the top panel to the cabinet. Reconnect the COLD and HOT water supply hoses to the ports at the back of the washer.
Step 14. Plug your appliance into the power supply and turn the water valve back on. Try running a spin cycle to make sure the problem has been fixed.
3. Failed Motor
Your machine’s drum will not be able to turn if the motor has failed. Here’s what you’ll need to do to replace the motor assembly in your Amana washing machine…
Replacing Failed Motor In Front Loader Amana Washing Machine
Do the following to replace a failed drive motor in your Amana front loader washing machine…
Step 1. Disconnect your machine from its power supply in order to prevent electrocution.
Step 2. Take out the nuts holding the rear access panel. Lift the panel off the machine and set it aside.
Step 3. Carefully take the drive belt off the motor pulley and drive pulley. Unplug the wire harnesses attached to the motor (make sure to note where each connector goes).
Step 4. Use a socket wrench to remove the mounting bolts holding the motor assembly to the bottom of the machine. Carefully take the motor out of the cabinet and set it aside.
Step 5. Remove your new washing machine drive motor from its packaging. Mount the new motor at the bottom of the tub and apply the bolts using your socket wrench.
Step 6. Plug each wire harness into its appropriate terminal on the new motor. Loop the belt around the motor pulley and and drive pulley (the grooved side of the belt should face downwards).
Step 7. Put the rear access panel back on the cabinet and use your nut-driver to apply the screws. Plug your appliance back into its power supply and try running a spin cycle.
Replacing Failed Motor In Top Loader Amana Washing Machine
Here are the steps you’ll need to take to replace the motor in your Amana top loader washing machine…
Step 1. Turn off your machine’s water supply and disconnect the power cord from the outlet before starting this repair.
Step 2. Spread a rag on the floor underneath the inlet hoses. Unscrew the two water supply lines from the ports on your machine (water will spill out).
Step 3. Put some tape on your machine’s lid to secure it. Release the spring clamp on the drain hose and pull the hose off the machine.
Step 4. With someone to assist you, tilt the washing machine backwards carefully and lay it on the floor.
Step 5. Take out the screws holding the belt guard using your nut-driver. Take the drive belt off the transmission pulley and motor pulley.
Step 6. Disconnect the wire connector from the terminal on the motor. Use your socket wrench to take out the bolts holding the drive motor to the bottom of the tub.
Step 7. Carefully lift the motor assembly off the tub and set it aside. Remove your new motor from its packaging and mount it at the bottom of the tub. Apply the bolts with your socket wrench.
Step 8. Plug the wire connector to the new motor. Loop the drive belt around the two pulleys. Put the belt guard back on and apply the nuts.
Step 9. Carefully lift your washing machine back onto its feet and peel the tape off the lid.
Step 10. Reattach the drain hose to the port on your machine and secure it using the spring clamp.
Step 11. Connect the two water supply lines back to the machine. Plug the power cord back into the electrical outlet and turn the water valve back on. Try running a spin cycle to see if the problem has been fixed.
4. Damaged Transmission Assembly (Top Loaders)
Replace the transmission assembly in your top loader Amana washing machine by doing the following…
Step 1. Disconnect your machine from the power outlet and turn the water valve off in order to prevent water leaks or electrocution.
Step 2. Using a pair of pliers, unscrew the two water inlet hoses from the ports on your machine (make sure to keep a rag nearby to clean any water that leaks out).
Step 3. Secure your machine’s lid using some tape. Use a nut-driver to take out the nuts at the back of the machine holding the top panel. Lift the top panel up and support it.
Step 4. Use your flat-blade screwdriver to pry the tub cover off the tub assembly and set it aside.
Step 5. Pry the cap off the agitator and use a 7/16 inch socket wrench to take out the agitator bolt. Lift the agitator out of the tub and set it aside.
Step 6. Take out the tub nut using a hammer and tub nut wrench. Lift the inner tub off the shaft and set it aside. If you have any trouble with this, apply some anti-rust oil to the shaft.
Step 7. Use a hammer to carefully knock the drive block off the drive tube. Lower the top panel back onto the cabinet and use your nut-driver to apply the screws at the back.
Step 8. Carefully tilt the washer forwards and lay it on the floor (get someone to help you if needed).
Step 9. Use a 5/16 inch nut-driver to take out the nuts holding the belt guard. Carefully take the drive belt off the motor pulley and transmission pulley).
Step 10. Unplug the wire harness attached to the motor assembly and release the wire from the retainer.
Step 11. Use a socket wrench to take out the nuts holding the motor to the transmission plate. Pull the motor off the machine and set it aside.
Step 12. Disconnect the wire connector attached to the start capacitor and shift actuator. Use your nut-driver to remove the screws holding the shift actuator and start capacitor to the transmission plate.
Step 13. With a 13mm socket wrench, take out the nut holding the transmission pulley.
Step 14. Pry the tabs on the splutch housing. Pull the splutch housing, basket drive gear, and spring off the shaft.
Step 15. Use your nut-driver to take out the bolts holding the transmission assembly to the bottom of the tub. Carefully pull the transmission assembly out of the machine and set it aside.
Step 16. Take your new washing machine transmission out of its packaging. Mount the new transmission at the bottom of the tub and apply the bolts with your socket wrench.
Step 17. Put the spring, drive gear, and splutch housing onto the transmission shaft. Place the pulley wheel on the new shaft and apply the nut with your socket wrench.
Step 18. Mount the start capacitor on the new transmission and secure it by applying the bolt. Plug the wire connector back to the capacitor.
Step 19. Place the shift actuator onto the new transmission and use your nut-driver to apply the bolt. Reconnect the wire harness to the actuator.
Step 20. Put the motor assembly onto the transmission plate and apply the mounting bolts with your socket wrench. Plug the wire harness back to the motor and secure it in the retainer.
Step 21. Loop the drive belt around the transmission pulley and motor pulley (make sure the grooved side of the belt faces inwards). Put the belt guard back in place and secure it using the bolts.
Step 22. Carefully lift your machine back onto its feet and use your nut-driver to take out the bolts securing the top panel. Lift the top panel and support it.
Step 23. Push the drive block firmly down the drive tube. Lower the inner tub onto the shaft.
Step 24. Put the tub nut back in place and tighten it with the tub nut wrench and a hammer.
Step 25. Put the agitator back on the shaft and use your socket wrench to apply the mounting bolt. Snap the cap back onto the agitator.
Step 26. Snap the tub cover onto the tub assembly. Lower the top panel and snap it into the cabinet. Use your nut-driver to apply the bolts at the back.
Step 27. Reattach the two water supply lines to the ports at the back of your machine. Plug the power cord back into the outlet and turn the water supply back on. Try running a spin cycle to see if the problem has been fixed.
Amana Washing Machine Banging During Spin Cycle — Solution
If your Amana washing machine is banging during spin cycles, here are the issues to look for…
1. Uneven Legs
If your machine shakes too much during spin cycles, the fault could be from the legs. If your notice that your machine’s legs are unbalanced, you’ll need to tilt the machine backwards and adjust them as needed.
2. Damaged Suspension Rods (Top Loaders)
Here are the steps you’ll need to take to replace damaged suspension rods in your top loader Amana washing machine…
Step 1. Turn off your washing machine’s water supply and unplug the power cord from the outlet before starting in order to avoid electrocution and water leakage.
Step 2. Release the spring clamp holding the drain hose to the back of the washing machine. Pull the hose off the machine.
Step 3. Spread a towel on the floor underneath the water supply hoses to catch any water leak. Use your pliers to unscrew the COLD and HOT water supply lines from the ports at the back of your machine.
Step 4. Secure the lid of your machine using some tape. With a nut-driver, remove the bolts at the back of your machine holding the top panel. Lift the top panel and support it using a lanyard or by laying it against a wall.
Step 5. Lift one of the suspension rod and take the bearing and socket off. Lower the rod through the opening on the cabinet and unhook it from the spring. Repeat this process with the other rods.
Step 6. Lower the top panel and snap it back into the cabinet. Apply the two bolts at the back to secure the top.
Step 7. With the help of another person, tilt your washing machine backwards carefully and lay it on the floor.
Step 8. Slide each of the four suspension rods through the openings on the tub. Take your new suspension rod kit out of its packaging.
Step 9. Slide each of the new rods through the holes on the outer tub. Carefully lift the machine back onto its feet.
Step 10. Remove the nuts at the back of your machine holding the top panel. Lift the panel and support it.
Step 11. Hook a spring onto one of the suspension rods. Pass the rod through the opening on the cabinet and secure it using the bearing and socket. Repeat this process with the other rods.
Step 12. Lower the top panel and snap it into the cabinet. Use your nut-driver to apply the screws at the back to secure it. Peel the tape off your machine’s lid.
Step 13. Reattach the drain hose to the back of your washer and secure it with the spring clamp.
Step 14. Connect the two water supply lines back to the ports at the back of your machine (ensure that the hoses are secured properly so water won’t leak out).
Step 15. Plug your machine back into the power outlet and turn the water valve back on. Test the machine by running a spin cycle.
3. Damaged Balance Ring (Top Loaders)
Replace a damaged balance ring in your Amana top loader washing machine by doing the following…
Step 1. Ensure that your washing machine is disconnected from the power supply before starting this repair in order to prevent electrocution.
Step 2. Secure the lid of your washing machine by putting some tape on it. Remove the screws at the back of the machine securing the top panel. Lift the top panel upwards and support by leaning it against a wall or using a lanyard.
Step 3. Pry the tub cover off the tub assembly and set it aside. Use a flat-blade screwdriver to release the tabs holding the balance ring between the inner tub and outer tub. Lift the balance ring out and set it aside.
Step 4. Take your new balance ring out of its packaging. Push it into place between the inner tub and outer tub. Rotate the ring clockwise to lock it in place.
Step 5. Snap the tub cover onto the tub assembly. Lower your machine’s top panel and snap it into the cabinet. Apply the bolts at the back with your nut-driver to secure the top panel.
Step 6. Plug your washer back into its power outlet and try running a spin cycle to see if the problem has been fixed.
4. Damaged Shock Absorber (Front Loaders)
Replace a damaged shock absorber in your front loader Amana washing machine by doing the following…
Step 1. Unplug your washing machine from the power outlet before starting this repair in order to prevent electrocution.
Step 2. Using a 1/4 inch nut-driver, take out the bolts at the back of your machine holding the top panel. Slide the panel backwards a few inches and lift it off the cabinet.
Step 3. Pull the soap drawer out and press the tab inside to release it from the housing.
Step 4. Remove the screws next to the detergent drawer housing. Use your nut-driver to remove the screws holding the control panel to the front of the cabinet. Pull the panel off and lay it on top of the cabinet.
Step 5. Open your machine’s door. Using either a pair of needle-nosed pliers or a flat-blade screwdriver, take out the retaining wire holding the door boot seal (make sure you do not damage the seal). Peel the door seal off the door opening.
Step 6. Use your Philips screwdriver to take out the screws holding the door lock to the cabinet.
Step 7. Tilt your machine backwards a bit and support the front with some blocks. With your screwdriver, take out the screws at the bottom of the front panel.
Step 8. Set your machine back onto its feet and take out the nuts at the top of the front panel. Carefully lift the entire front panel off your washing machine and set it aside.
Step 9. Use a pair of pliers to squeeze the upper mount of the shock absorber you want to replace. Press the tabs on the upper mount using a flat-blade screwdriver. Rotate the shock mount with your pliers to release it. Repeat this process with the lower mount.
Step 10. Take the shock absorber out of your machine and set it aside. Remove your new washer shock absorber from its packaging. Place the lower mount at the bottom of the cabinet and rotate it to secure.
Step 11. Align the upper mount with the tub opening and rotate it to secure. Snap the front panel back onto the cabinet and apply the screws at the top of the front panel.
Step 12. Tilt your machine backwards and place the supports underneath. Use your screwdriver to apply the four screws at the bottom.
Step 13. Set your machine back on its feet and open the door. Secure the door lock to the cabinet by applying the screws.
Step 14. Fit the door gasket back around the door opening and use your pliers or screwdriver to fit the retaining wire.
Step 15. Snap the control panel onto the front of the cabinet. Apply the control panel mounting screws and apply the screws beside the detergent drawer housing. Slide the detergent drawer back in place.
Step 16. Put your machine’s top panel back on and apply the bolts at the back with your nut-driver. Plug the power cord back into the outlet and try running a spin cycle to see if the problem has been fixed.
5. Warped Drum Bearing (Only Applicable To Top Loaders)
Here are the tools you’ll need to replace the bearings in your Amana top loader washing machine…
- New Bearing Kit
- Bearing Installation kit
- Adjustable Wrench
- Pliers
- Flat-blade Screwdriver
- Philips Screwdriver
- 1/4 Inch Allen Wrench
- Ratchet With 3/8 Inch Socket
- 5/16 Inch Nut-driver
- Hammer
- Putty Knife
- 7/16 Inch Socket Wrench With Long Extension
Replace the tub bearings in your Amana top loader washing machine by doing the following…
Step 1. Shut the water supply to your machine and disconnect the power cord from the outlet before starting this repair in order to prevent water leaks and electrocution.
Step 2. Secure the lid of your machine with some tape. Insert a putty knife underneath the top panel. Lift the panel and support against a wall or with a lanyard (do not rely on the panel hinges for support).
Step 3. Using a pair of pliers, release the spring clamp holding the re-circulation hose to the tub cover. Pull the hose off.
Step 4. Pry the tabs on the tub cover to release it from the tub assembly. Take the cap off the agitator and use your 7/16 inch socket wrench to take the bolt out. Pull the agitator assembly out of the machine and set it aside.
Step 5. Using your Philips screwdriver, remove the screws holding the basket hub inside the tub. Carefully lift the inner tub off the shaft and set it aside (if you have any difficulty doing this, apply some penetrating oil to the shaft).
Step 6. Lower the top panel and snap it into the cabinet. Tilt the machine backwards a bit and lay support it against the wall.
Step 7. Loosen the nut holding the rotor to the bottom of the tub using your 1/4 inch Allen wrench. Carefully lift the rotor assembly off the stator and set it aside.
Step 8. Remove the bolts securing the stator to the bottom of the tub with a 3/8 inch socket. Lift the stator and stator plate off the tub. Unplug the wire harness from the stator and set it aside.
Step 9. Using a pair of pliers, squeeze the tip of the drive shaft. Use your adjustable wrench to loosen the nut securing the drive shaft.
Step 10. Knock the drive shaft through the tub opening using a hammer. Set your machine upright, then lift and support the top panel. Take the drive tube out of the tub.
Step 11. Using a hammer and the bearing removal rod (provided in the installation tool kit), knock out the lower bearing out of the tub.
Step 12. Lower the top panel and tilt your washer back. Remove the three bearing pieces underneath your machine.
Step 13. From under the tub, knock out the upper bearing with your hammer and rod. Set your washer on its feet and lift the top. Take the upper bearing out of the tub and discard it.
Step 14. Take your new tub bearing kit out of its packaging. Clean the bearing seat using a cloth.
Step 15. Push the new upper bearing into the seat. Take your bearing installation tool and unscrew the three lower pieces on the shaft. Slide the installation tool shaft through the bearing opening.
Step 16. Close the top panel and tilt the machine backwards. Slide the drive tube, bearing washer, and lower bearing onto the installation tool shaft.
Step 17. Put the three lower pieces of the installation tool back on. Tighten the nut using your adjustable wrench (this will force the lower bearing into the housing).
Step 18. Once the lower bearing is in place, use the wrench to loosen the nut and take the three installation tool pieces off the shaft.
Step 19. Set your machine on its feet and take the installation tool out of the tub. Slide the new drive tube through the opening on the upper bearing and snap knock it firmly into place with a hammer.
Step 20. Tilt the machine backwards and support it against the wall. Secure the drive tube nut by applying the nut with your adjustable wrench.
Step 21. Plug the wire connector back to the stator. Put the stator and mounting plate back on the tub and apply the bolts using your socket wrench.
Step 22. Place the rotor assembly on the drive shaft and tighten the nut with your 1/4 inch Allen wrench.
Step 23. Set the machine upright, then lift and support the top panel. Fill the two grooves of the new bearing seal using the grease provided.
Step 24. Apply a bead of the provided sealant around the new bearing (to help the sealant cure, you’ll need to leave the machine for a day before running a cycle).
Step 25. Slide the new bearing down the drive shaft. Use a hammer and the provided installation tool rod to firmly push the new seal into place.
Step 26. Apply an even coat of sealant on top of the new seal. Clean any excess grease or sealant on the shaft or tub using a towel.
Step 27. Carefully lower the inner tub onto the shaft. Put the basket hub back in place and apply the screws with your Philips screwdriver.
Step 28. Snap the tub cover back onto the tub assembly. Connect the re-circulation hose to the port on the tub cover and secure the hose with the spring clamp.
Step 29. Lower the agitator into the tub and apply the bolt with your socket wrench. Snap the cap back on the agitator.
Step 30. Lower the top panel back onto the cabinet and snap it into place. Peel the tape off the lid.
Step 31. Reconnect your machine to the power outlet and make sure the problem has been fixed by running a spin cycle.
Amana Washing Machine Not Going Through Cycles — Quick Fix
If your Amana washing machine isn’t going through cycles, it indicates that the shift actuator is defective. Here’s what you’ll need to do to replace this part in your Amana washing machine…
Step 1. Disconnect your washer’s power cord from the outlet and turn the water valve off before starting this repair in order to prevent water leaks or electrocution.
Step 2. Secure your machine’s lid with some tape. Press the clamp on the drain hose at the back of the machine and slide it out of place. Pull the drain hose off your washer.
Step 3. Spread a rag on the floor underneath the water supply hoses in order to catch any water leaks. With your pliers, unscrew the COLD and HOT water supply lines from the ports at the back of your machine.
Step 4. Tilt your machine backwards and lay it on the floor (get someone to help you if needed).
Step 5. Using a 5/16 inch nut-driver, remove the screws holding the belt guard to the bottom of the machine.
Step 6. Remove the screws holding the shift actuator next to the drive pulley using a Philips screwdriver. Unplug the wire connector from the actuator and set it aside.
Step 7. Take your new washing machine shift actuator out of its packaging. Plug the wire connector to the new actuator.
Step 8. Mount the new actuator at the bottom of the machine and secure it by applying the screws with your Philips screwdriver.
Step 9. Put the belt guard back in place and use your nut-driver to apply the bolts. Carefully lift your washing machine back onto its feet and peel the tape off the lid.
Step 10. Reattach the drain hose to the back of the washer and secure it with the spring clamp.
Step 11. Connect the two water supply lines to the ports at the back of your machine (ensure that they are secured properly so there’s no chance of water leakage).
Step 12. Reconnect the power cord to the outlet and turn the water valve back on. Try running a wash cycle to see if the issue has been fixed.
Note: Please keep in mind that the processes of the repairs above will vary a bit depending on the model of your washing machine.
