If your KitchenAid washing machine door is giving you problems, don’t worry. In this detailed guide we’ll be providing solutions to various issues you might have with your washing machine door
Table of Contents
How To Replace KitchenAid Washing Door Boot Seal — Solved
To replace a damaged KitchenAid washing machine door boot seal, follow the steps below…
Step 1. Ensure that your appliance is disconnected from the power outlet before starting this procedure, in order to prevent electrocution.
Step 2. Use a 1/4 inch nut-driver or a Torx-20 screwdriver to take out the bolts at the back of the machine securing the top panel. Slide the panel backwards a few inches, then lift it off the cabinet.
Step 3. Pull the soap tray out of the dispenser. To completely release the tray, press the little tab inside.
Step 4. Disconnect the control panel’s wire harness from the main control board, then pull the wire harness out of the retaining bracket.
Step 5. Loosen the bolt on the control panel next to the dispenser opening. Pry the control panel off the machine and set it aside.
Step 6. Using your Torx screwdriver, take out the bolts holding the lower front access panel. Pry the panel off the cabinet and set it aside.
Step 7. Open your washing machine’s door. Loosen the bolts on the front panel securing the door lock assembly.
Step 8. Wedge a flat-blade screwdriver underneath the retaining wire around the door boot seal. Carefully work the screwdriver around until the band comes off.
Step 9. Pry the door gasket off the front panel. Take out the Torx screws at the top and bottom of the main front panel.
Step 10. Lift the front panel off the cabinet carefully, then set it aside. Detach the little tube from the port at the top of the door seal.
Step 11. Use a 7mm socket to loosen the bolt holding the inner retaining band to the door boot seal. Pry the door seal off the drum, then discard it.
Step 12. Prepare your new washing machine door seal for installation by unpacking it. Carefully fit the new seal around the drum opening.
Step 13. Fit the inner retaining band around the door seal, then tighten the bolt using your 7mm socket.
Step 14. Carefully remount the main front panel on the cabinet, then apply the Torx screws at the top and bottom.
Step 15. Snap the lower front access panel onto the machine, then tighten the screws to secure it.
Step 16. Open your washing machine’s door. Reach behind the front panel, then push the door switch assembly back into place. Secure the door lock by tightening the screws.
Step 17. Fit the new door boot seal around the door opening. Using a flat-blade screwdriver or needle-nosed pliers, fit the retaining wire around the new seal.
Step 18. Pass the control panel’s wire harness through the opening on the top frame brace. Snap the panel onto the mounting bracket, then apply the bolt to secure it.
Step 19. Push the soap tray back into the dispenser. Plug the control panel connector into the main control board.
Step 20. Secure the control panel’s wire in the retaining bracket on the cabinet. Mount the top panel on the cabinet, then push it forwards. Secure the panel by applying the Torx screws.
Step 21. Plug your appliance back into the power outlet. To ensure that the machine works properly, try running a wash cycle.
How To Replace KitchenAid Washing Machine Door Lock — Quick Fix
To replace a damaged KitchenAid washing machine door lock, follow the steps below…
Front Loaders
Take the following steps to replace your front loader KitchenAid washing machine door lock…
Step 1. Ensure that your machine is disconnected from the outlet before starting this repair in order to prevent electrocution.
Step 2. Open the door of your washing machine. Loosen the bolts securing the door switch to the front panel.
Step 3. Using a flat-blade screwdriver or needle-nosed pliers, pry off the retaining band securing the door seal to the front panel (take care not to damage the seal).
Step 4. Pry the door seal off the front panel. Reach in behind the front panel, then pull the door lock out of place.
Step 5. Disconnect the wire harness attached to the door lock assembly. Discard the old door lock, then prepare the new one for installation by unpacking it.
Step 6. Plug the wire harness into the new door lock assembly. Push the door lock into place behind the front panel. Secure the door switch to the panel by applying the Torx screws.
Step 7. Fit the door boot seal around the front panel. Using needle-nosed pliers or a flat-blade screwdriver, fit the retaining wire around the door seal.
Step 8. Plug your washing machine’s power cord into the outlet. Try turning the machine on and running a cycle to ensure that everything works properly.
Top Loaders
Replace your top loader KitchenAid washing machine door lock by following the steps below…
Step 1. Ensure that you disconnect your washing machine from the outlet before starting this repair in order to prevent electrocution.
Step 2. Turn your water supply taps off to prevent leakage. Using pliers if needed, disconnect the COLD and HOT water supply hoses from the ports at the back of the machine.
Step 3. Using a 1/4 inch nut-driver, take out the bolts securing the rear cover to the control panel. Pry the cover off and set it aside.
Step 4. Disconnect the lid lock wire harness from the control board on the panel. Release the lid lock wire from the retainer on the top panel.
Step 5. Using your nut-driver, loosen the bolt securing the wiring and tube guard to the back of the machine. Take the guard of and set it aside.
Step 6. Place some tape on the lid of your machine. Take out the bolts at the back of the machine securing the top panel. Lift the top panel carefully, then support it.
Step 7. Using a flat-blade screwdriver, carefully pry the old door switch out of the slot on the top panel.
Step 8. Pull the lid lock wire out of the retainers at the bottom of the top panel. Pull the lid lock off the panel and discard it.
Step 9. Prepare your new washing machine lid lock for installation by unpacking it. Snap the new lid switch into place at the bottom of the top panel.
Step 10. Pass the wire harness of the new lid switch through the opening on the top panel. Secure the wire in the retaining brackets at the bottom of the panel.
Step 11. Lower the top panel and snap it onto the cabinet. Secure the top panel by applying the 1/4 inch bolts at the back.
Step 12. Peel the tape off your washer’s lid. Plug the new lid switch wire harness into the control board.
Step 13. Put the wiring and tube guard in place, then tighten the bolts to secure. Snap the rear cover onto the control panel. Use your 1/4 inch nut-driver to apply the bolts.
Step 14. Reconnect the HOT and COLD water inlet hoses to their corresponding ports at the back of the machine (in order to prevent leakage, ensure that the hoses are properly connected).
Step 15. Turn the water taps back on, then plug the power cord into the outlet. Ensure that the machine works properly by running a wash cycle.
Dryers
Take the following steps to replace the door lock in your KitchenAid dryer…
Step 1. Disconnect your machine from the power outlet before starting this repair in order to prevent electrocution.
Step 2. Pull the lint filter out from the top of the dryer. Use a screwdriver to take out the bolts holding the top panel to the filter housing.
Step 3. Insert a tool such as a putty knife underneath top panel (this will help release the locking clips). Lift the top panel carefully and support it.
Step 4. Using a flat-blade screwdriver if needed, disconnect the door switch wire harness behind the front panel.
Step 5. Open the door of your machine. Using your screwdriver, take out the bolts securing the door switch to the front panel. Pull the door switch out and set it aside.
Step 6. Prepare your new washing machine door switch for installation by unpacking it. Mount the new door switch on the front panel, then tighten the bolts.
Step 7. Plug the wire connector into the new door switch. Close your dryer’s door. Lower the top panel carefully, then snap it onto the cabinet.
Step 8. Use your screwdriver to tighten the bolts that secure the top panel to the filter housing.
Step 9. Push the lint filter back into its housing. Plug your appliance into the power outlet, then ensure that it works properly by running a cycle.
Note: Please keep in mind that the steps above will vary depending on the model of your machine.
Check out these other articles…
Kenmore Washing Machine Is Not Spinning [7 Solutions]
LG Washing Machine Is Not Heating [3 Causes & Solutions]
KitchenAid Washing Machine Is Not Draining [2 Problems & Proven Solutions]
KitchenAid Washing Machine Motor [2 Issues & Proven Solutions]
KitchenAid Washing Machine Water Inlet Valve [2 Issues & Proven Solutions]
KitchenAid Washing Machine Is Leaking [4 Causes & Proven Solutions]
KitchenAid Washing Machine Is Not Spinning [12 Causes & Proven Solutions]
How To Replace KitchenAid Dryer Door Catch — Quick Fix
Replace the door catch in your KitchenAid dryer by following the steps below…
Step 1. In order to prevent any chances of electrocution, it is advised that you disconnect your appliance from the outlet before starting this procedure.
Step 2. Open the dryer’s door. While supporting the door, loosen the bolts securing the door hinge to the front panel using a Torx screwdriver. Lift the door assembly off the machine.
Step 3. Set the door assembly face-down on a flat surface. Use your screwdriver to take out the bolts holding the outer and inner door frame together.
Step 4. Lift the inner door frame off the assembly and set it face-down on the floor. Using your Torx screwdriver, take out the bolts securing the cover plate and door catch to the inner frame.
Step 5. Take the cover plate and door catch out, then set them aside. Prepare your new door catch for installation by unpacking it.
Step 6. Position the new door catch on the inner door frame, then place the cover on top. Secure the catch and cover by tightening the Torx screws.
Step 7. Lift the inner door frame, then lower it onto the door assembly. Secure the two door frames by tightening the bolts.
Step 8. Lift the door assembly, then mount the hinges on the front panel. Secure the door to the panel by applying the Torx screws.
Step 9. Plug your dryer back into the outlet, then ensure that everything works properly by running a cycle.
How To Replace KitchenAid Washing Machine Outer Door Frame — Solved
Follow the steps below to replace the outer door frame in your KitchenAid washing machine…
Front Loaders
Take the following steps to replace the outer door frame in your front loader KitchenAid washing machine…
Step 1. Before starting this repair, ensure that you disconnect your washing machine from the power outlet.
Step 2. Open your washer’s door. Using a Torx-20 screwdriver, take out the bolts holding the handle to the door assembly.
Step 3. Use your screwdriver to take out the bolts securing the two door frames. Pry the outer door frame off the assembly and set it aside.
Step 4. Prepare the new outer door frame for installation by unpacking it. Mount the new frame onto the door assembly.
Step 5. Secure the two door frames by tightening the Torx screws. Push the door handle back into place, then apply the bolts. Plug your machine back into the power outlet.
Dryers
To replace the outer door frame in your KitchenAid dryer, take the following steps…
Step 1. It is advised that you disconnect your machine’s power cord from the outlet before starting this procedure in order to prevent electrocution.
Step 2. Open the door of the machine. Using a Torx screwdriver, loosen the bolts securing the door hinge to the front of the cabinet.
Step 3. Lift the door assembly off the machine carefully, then set it face-down. Using your screwdriver, take out the bolts holding the outer and inner door frames.
Step 4. Take the outer door frame off the assembly and discard it. Unpack your new dryer outer door frame.
Step 5. Attach the outer door frame to the door assembly, then apply the Torx screws to secure.
Step 6. Lift the door assembly, then carefully mount it on the cabinet. Apply the bolts to secure the hinges to the front panel. Plug your dryer back into the outlet.
How To Replace KitchenAid Washing Machine Door Glass — Solution
To replace your KitchenAid washing machine door glass, follow the steps below…
Front Loaders
Take the following steps to replace your front loader KitchenAid washing machine door glass…
Step 1. Disconnect your appliance from the power outlet before starting this repair in order to prevent electrocution.
Step 2. Open the door of your machine. Take out the bolts securing the door hinges to the front panel. Lift the door assembly off the cabinet and set it face-down.
Step 3. Using your screwdriver, take out the bolts securing the outer and inner door frames. Lift the inner frame off and set it aside.
Step 4. Lift the old door glass off the outer door frame (ensure that you note the positioning of the frame).
Step 5. Prepare your new door glass for installation by unpacking it. Position the new door glass on the outer door frame. Lower the inner door frame onto the assembly, then apply the bolts to secure them.
Step 6. Lift the door assembly, then mount the hinges on the cabinet. Apply the Torx screws to secure the hinges to the front panel. Plug your washing machine back into the outlet.
Dryers
To replace the door glass in your KitchenAid Dryer, follow the steps below…
Step 1. Prevent any chances of electrocution by disconnecting your appliance from the power outlet before starting this repair.
Step 2. Open the dryer’s door. Loosen the bolts securing the door hinge to the front panel using a Torx screwdriver. Carefully lift the door assembly off the cabinet.
Step 3. Set the door assembly face-down. Loosen the bolts holding the outer and inner door frames together. Lift the inner door frame off.
Step 4. With your Torx screwdriver, loosen the bolts on the inner door frame securing the door glass retaining bracket. Lift the glass off the frame, then discard it.
Step 5. Prepare the new door glass for installation. Mount the door glass on the inner frame, then tighten the bolts to secure the retaining bracket.
Step 6. Lower the inner door frame onto the outer frame. Secure the door assembly by tightening the bolts.
Step 7. Lift the door assembly, then carefully mount the hinges on the front panel secure the door by tightening the bolts. Close the door, then plug your machine back into the outlet.
Note: Please keep in mind that some of the steps above will be a bit different depending on your washer’s model.
How To Replace KitchenAid Washing Machine Door Hinge — Quick Fix
Take the following steps to replace your KitchenAid washing machine door hinge…
Front Loaders
Replace your front loader KitchenAid washing machine door hinge by following the steps below…
Step 1. Prevent any chances of electrical damage by disconnecting your machine from the power outlet before starting this repair.
Step 2. Using a Torx screwdriver, take out the bolts holding the hinges to the front of the cabinet. Lift the door assembly off the cabinet, then set it face-down on a flat surface.
Step 3. Use your screwdriver to take out the bolts holding the outer and inner door frames together. Lift the inner door frame off and turn it over.
Step 4. Loosen the bolts holding the door hinge cover plate. Take the plate off, then pull the hinge off the frame.
Step 5. Unpack your new washer door hinge. Slide the plastic caps onto the new door hinge.
Step 6. Mount the new door hinge on the inner frame, then put the cover plate on. Apply the bolts to secure it.
Step 7. Lower the inner frame onto the outer frame, then secure them by tightening the screws.
Step 8. Lift the door assembly carefully, then mount the hinges on the cabinet. Tighten the bolts to secure the new hinge. Close the door, then plug your machine back into the outlet.
Dryers
Follow the steps to change a damaged door hinge in your KitchenAid dryer…
Step 1. It is advised that you disconnect your machine from the power outlet before starting this procedure, in order to avoid electrocution.
Step 2. Open your dryer’s door. With a Torx screwdriver, take out the bolts securing the door hinge to the front panel. Lift the door assembly off the cabinet, then set it face-down.
Step 3. Take out the bolts securing the inner and outer door frames together using a Torx screwdriver. Lift the inner frame off, then turn it over.
Step 4. Loosen the bolts holding the cover to the hinge. Take the cover off, then pull the hinge off the door frame.
Step 5. Unpack your new washing machine door hinge. Slide the caps onto the pins of the new hinge.
Step 6. Position the new hinge on the inner frame, then put the cover on. Apply the bolts to secure the hinge cover.
Step 7. Lower the inner door frame onto the outer frame, then apply the bolts using your screwdriver.
Step 8. Lift the door assembly, then mount the hinges on the front panel. Secure the door by applying the bolts. Plug your appliance back into the outlet.
Note: Please keep in mind that the some of the steps above will be a bit different depending on the model of your machine.
