Is your Frigidaire washing machine not starting? If so, you’ve come to the right place. This detailed guide will explain the causes of this issue and provide easy-to-follow steps on how to fix them. So, without further ado, let’s get right to it…
Table of Contents
Frigidaire Washing Machine Not Starting — Solution
Is your Frigidaire washing machine not starting? If so, look for the following issues…
1. Washing Machine Isn’t Getting Any Power
If your washing machine isn’t starting, the first thing you should check is the power outlet. Make sure that the outlet is switched on before trying to use your washer. If your machine still doesn’t work, unplug it from the outlet and try plugging another appliance in.
If the other appliance also doesn’t work, it means that the power outlet is faulty. You’ll need to get an electrician to take a look at the problem.
2. Start Capacitor Has Failed
Here’s what you’ll need to do to replace the start capacitor in your washing machine…
How To Replace Capacitor In Frigidaire Top Loader Washing Machine
Do the following to replace the capacitor in your Frigidaire top loader washing machine…
Step 1. In order to prevent any chances of electrocution, it is advised that you unplug your washing machine’s power cord from the power supply before starting this repair.
Step 2. Put some tape over the lid of your washing machine to secure it. Insert a putty knife under the main top panel of your washing machine to release the two retaining clips.
Step 3. Lift your washing machine’s main top panel and support it. Use a Philips screwdriver to remove the two screws at the bottom of the front panel. Lift the panel upwards and pull it off your washing machine.
Step 4. Use your Philips screwdriver to remove the screws holding the motor shield. Detach the shield from the drum. The capacitor will be mounted at the back of the motor shield. Disconnect the two electrical connectors attached to the capacitor.
Step 5. Pull the motor shield out of your washing machine. Peel the tape holding the capacitor to the shield and set the old start capacitor aside.
Step 6. Take your new start capacitor out of its packaging and install it in the motor shield (put some tape on the capacitor to secure it to the shield).
Step 7. Connect the electrical connectors to the new start capacitor. Put the motor shield back onto the drum and apply the two screws with your Philips screwdriver to secure it.
Step 8. Put the main front panel of your washing machine back on and apply the two screws at the bottom with a Philips screwdriver to secure it. Lower the main front panel of your washing machine and snap it back into place.
Step 9. Peel the tape off the lid of your washing machine. Plug your washing machine’s power cord back to the power outlet and try running a wash cycle to see if the problem has been fixed.
How To Replace Capacitor In Frigidaire Laundry Center Washing Machine
Here’s what you’ll need to do to replace the start capacitor in your Frigidaire laundry center washing machine…
Step 1. In order to prevent any chances of electrocution or water leakage, we advise unplugging your washing machine from its power outlet and turning off the water supply valve before starting this repair.
Step 2. Move your washing machine forward to give you more working space. Use your screwdriver to release the vent tube from the back of your washing machine.
Step 3. Unscrew the water supply lines from the inlet ports at the back of your washing machine (make sure to keep a rag nearby in case water spills out of the hoses).
Step 4. Pull the drain hose out of your home drain. Put some tape over the lid of your washing machine to secure it.
Step 5. With the help of another person, carefully tip your washing machine backwards and lay it on the floor. Using a 10mm socket wrench, take out the bolt holding the capacitor strap to the base of your washing machine. Let the capacitor fall out of place (do not touch the capacitor yet).
Step 6. Use a pair of pliers to touch the two terminals on the capacitor to release any charge that may still be in the capacitor. Disconnect the two electrical connectors from the start capacitor.
Step 7. Set the old capacitor aside and take the new one out of its packaging. Connect the two electrical connectors to the new start capacitor. Mount the capacitor at the bottom of the machine and apply the bolt with your socket wrench to secure the retaining strap.
Step 8. Lift your washing machine upright and peel the tape off the lid. Push the drain hose back into your home drain.
Step 9. Connect the water supply hoses back to the inlet ports at the back of your washing machine (make sure to secure the connections properly to prevent water leakage).
Step 10. Reattach the venting to the back of your washing machine. Move your washing machine back into place. Plug your washing machine’s power cord back to the outlet and turn the water supply valve on. Try running a wash cycle to see if the problem has been fixed.
3. Door Isn’t Locked (Front Loader Washing Machines)
Most front loader washing machines won’t start a wash cycle if the door isn’t properly locked. Ensure that you firmly shut the door of your washing machine before starting a cycle.
If your washing machine’s door isn’t locking, you’ll need to replace the control board. Here’s how to do this…
Step 1. Please ensure that your washing machine is unplugged from the power supply before starting this repair in order to prevent any chances off electrocution.
Step 2. Open the door of your washing machine. Carefully peel the door boot seal off the door opening (you don’t need to take the seal off completely). Use a Philips screwdriver to remove the two screws holding the door lock assembly to your washing machine.
Step 3. Reach inside the washing machine behind the door seal and pull the door lock out of place. Disconnect the electrical connectors attached to the door lock. Set the old door lock aside and take the new one out of its packaging.
Step 4. Connect the electrical connectors to the new door lock assembly. Put the new door lock inside your washing machine and apply two screws with your Philips screwdriver to secure it.
Step 5. Carefully fit the door boot seal around the door opening and close your washing machine’s door. Plug your washing machine’s power cord back to the power outlet and try running a wash cycle to see if the problem has been solved.
4. Failed Interface Control Board
Here’s what you’ll need to do to replace a failed interface control board in your Frigidaire washing machine…
How To Replace Interface Control Board In Frigidaire Laundry Center Washing Machine
Do the following to replace the interface control board in your Frigidaire laundry center washing machine…
Step 1. In order to prevent electrocution, it is advised that you unplug your washing machine from its power outlet before starting this repair.
Step 2. Remove the two screws under the control panel holding the lower access panel of the dryer. Detach the panel from your washing machine and set it aside.
Step 3. Use your Philips screwdriver to remove the two mounting screws holding the control panel. Pull the panel downwards to release it. Release the control panel wires from the retainers.
Step 4. Set the control panel on the lid of your washing machine. There are two control boards on the panel; one for the washing machine and one for the dryer. Disconnect all the electrical connectors attached to the washing machine’s control board.
Step 5. Use your Philips screwdriver to remove the four screws holding the washing machine control board to the control panel. Pull the board off the control panel and set it aside.
Step 6. Take your new washing machine control board out of its packaging. Apply the four mounting screws with your Philips screwdriver to secure it. Connect all the electrical connectors to the new control board.
Step 7. Secure the control board wire in the retainer. Put the control panel back into place and apply the two screws at the bottom to secure it. Put the dryer lower access panel back on and apply the screws with your Philips screwdriver to secure it.
Step 8. Plug your washing machine’s power cord back to its power outlet. Try running a wash cycle to see if the problem has been fixed.
Check out these other articles…
Washing Machine Overfilling/Overflowing [Problems Solved]
Frigidaire Washing Machine Not Washing [Quick Fix]
Washing Machine Doesn’t Spin Dry [How To Fix]
Frigidaire Washing Machine Pump [Problems & Solutions]
Frigidaire Washing Machine Blinking Lights [How To Fix]
How To Replace Interface Control Board In Frigidaire Top Washing Machine
Do the following to replace a failed interface control board in your Frigidaire top loader washing machine…
Step 1. In order to prevent any chances of electrocution, we recommend unplugging your washing machine from its power outlet before starting this repair.
Step 2. Insert a small screwdriver into the holes at the back of the control panel. Detach the control panel from the housing and lay it on the lid of your washing machine.
Step 3. Disconnect all the electrical connectors attached to the interface control board. Use your Philips screwdriver to remove all the screws holding the control board to the panel. Pull the board off the panel off the board and set it aside.
Step 4. Take your new interface control board out of its packaging and set it on the control panel. Apply the screws with your Philips screwdriver to secure it. Connect each electrical connector to its appropriate terminal on the new control board.
Step 5. Snap the control panel into the control housing. Plug your washing machine back to its power outlet and try running a wash cycle to see if the problem has been fixed.
How To Replace Interface Control Board In Frigidaire Front Loader Washing Machine
Do the following to replace the interface control board in your Frigidaire front loader washing machine…
Step 1. It is recommended that you unplug your washing machine from its power outlet before starting this repair in order to prevent electrocution.
Step 2. Using a Philips screwdriver, remove the screws at the back of your washing machine holding the top panel. Slide the panel backwards and lift if off your washing machine.
Step 3. Pull out the detergent drawer and press the tab inside to take it out of your washing machine completely. Use your Philips screwdriver to remove the three screws beside the detergent drawer housing.
Step 4. Remove the two screws on the top corners of the control panel. Pry the panel off your washing machine with a flat-blade screwdriver.
Step 5. Disconnect each electrical connector from the control board (make sure to take note of where each connector goes). Remove all the screws holding the control board to the control panel. Set the control panel aside.
Step 6. Turn the control board over. Use a flat-blade screwdriver to pry the two halves of the control board apart. Use a pair of needle-nosed pliers to release the wire retainers from the back of the control board.
Step 7. Snap the two halves of the control board back together. Pry all the buttons off the control board. Take your new interface control board out of its packaging. Transfer the buttons to the new control board.
Step 8. Pry the indicator screen cover off the old control board. Remove the indicator screen from the old board and transfer it to the new one. Put the screen cover on.
Step 9. Snap the retainers into the holes on the new control board. Place the control board on the control panel and apply the screws with your screwdriver to secure it. Connect each electrical connector to its appropriate terminal on the new board.
Step 10. Snap the control panel onto the front of your washing machine and apply all the screws to secure it. Slide the detergent drawer back into the housing. Slide the top panel of your washing machine back on and apply the screws at the back to secure it.
Step 11. Plug your washing machine back to its power outlet and try running a wash cycle to see if the problem has been fixed.
5. Failed Drive Motor
Here’s how to replace a failed drive motor in your Frigidaire washing machine…
How To Replace A Failed Drive Motor In Frigidaire Laundry Center Washing Machine
Do the following to replace a failed drive motor in your Frigidaire laundry center washing machine…
Step 1. In order to prevent any water leaks or electrocution, we recommend unplugging your washing machine from its power supply and turning the water valve off before starting this repair.
Step 2. Pull your washing machine forwards to give you more working space. Use your screwdriver to remove the venting from the back of your washing machine.
Step 3. Unscrew the water supply hoses from the inlet ports at the back of your washing machine (keep a rag nearby in case water spills out of the hoses). Pull the drain hose out of your home drain.
Step 4. Put some tape over the lid of your washing machine to secure it. With the help of another person, carefully tilt the washing machine backwards and lay it on the floor.
Step 5. Use a 10mm socket wrench to take out the bolts holding the drive belt cover at the bottom of your washing machine. Pull the cover off and set it aside.
Step 6. Pull the drive belt off the two pulleys and set it aside. Disconnect the motor electrical connectors (make sure to note where each connector goes). Take out the mounting bolts holding the drive motor to the bottom of the machine (you’ll need a 1/2 inch socket wrench).
Step 7. Pull the drive motor off the drum and set it aside. Take your new washing machine drive motor out of its packaging. Mount the new drive motor under your washing machine and apply the bolts to secure it.
Step 8. Connect each electrical connector to its appropriate terminal on the new drive motor. Carefully fit the drive belt around the new motor pulley and the washer pulley (the grooved side of the belt should face inwards).
Step 9. Put the drive belt cover back on and apply the bolts with your 10mm socket wrench to secure it. Lift your washing machine upright and peel the tape off the lid.
Step 10. Insert the drain hose back into your home drain. Reattach the venting to the back of your washing machine.
Step 11. Connect the COLD and HOT water supply lines back to the inlet ports at the back of your washing machine (ensure that you secure the connections properly in order to prevent water leakage).
Step 12. Turn on your washing machine’s water valve and plug the power cord back into the outlet. Try running a wash cycle to see if the problem has been fixed.
How To Replace A Failed Drive Motor In Frigidaire Top Loader Washing Machine
Do the following to replace a failed drive motor in your Frigidaire top loader washing machine…
Step 1. Please remember to unplug your washing machine’s power cord from the power outlet before starting this repair in order to prevent any chances of electrocution.
Step 2. Place some tape over the lid of your washing machine to secure it. Insert a putty knife under the main top panel to release the two retaining clips. Lift the panel up and support it.
Step 3. Use a Philips screwdriver to remove the screws at the bottom of the washing machine’s front panel. Lift the front panel up slightly and pull it off your washing machine.
Step 4. Pull the tub forwards slightly and detach the horizontal and vertical springs from the front of the drum. Use your Philips screwdriver to remove the two screws holding the motor shield to the drum.
Step 5. Disconnect the electrical connectors attached to the capacitor and pull the motor shield out of the washing machine.
Step 6. Use a socket wrench to take out the front mounting bolt from the tub. Insert a block of wood under the drum and lift it up slightly. Insert the mounting nut into the opening on the tub above the mounting base (this will hold the front of the tub up).
Step 7. Disconnect the electrical connector from the motor. Push the idler pulley inwards to release the tension on the drive belt. Pull the belt out of your washing machine and set it aside.
Step 8. Using a 3/8 inch wrench, take out the bolts holding the motor assembly to the base of your washing machine. Pull the motor out of your washing machine and set it aside.
Step 9. Take your new motor assembly out of its packaging. Mount the new motor on the base inside your washing machine and apply the mounting bolts to secure it.
Step 10. Connect the electrical connector to the new motor assembly. Push the idler pulley inwards again and fit the drive belt back into place.
Step 11. Pry the tub upwards with your wooden support and pull the bolt out of place. Carefully lower the tub and properly apply the bolt to secure it.
Step 12. Connect the electrical connectors to the capacitor on the motor shield. Put the motor shield back in place and apply the screws with your Philips screwdriver to secure it.
Step 13. Hook the two suspension springs back to the base of your washing machine. Snap the main front panel of your washing machine back on and apply the two screws at the bottom to secure it.
Step 14. Lower the main top panel of your washing machine and snap it into place. Peel the tape off the lid of your washing machine. Plug your washing machine’s power cord back to the power outlet and try running a wash cycle to see if the problem has been fixed.
How To Replace A Failed Drive Motor In Frigidaire Front Loader Washing Machine
Do the following to replace a failed drive motor in your Frigidaire front loader washing machine…
Step 1. Please remember to unplug your washing machine from its power supply and turn off the water valve before starting this repair in order to prevent any chances of electrocution or water leakage.
Step 2. Unscrew the two water supply hoses from the inlet ports at the back of your washing machine (keep a rag nearby in case water spills out of the hoses). Use your Philips screwdriver to remove all the screws holding the rear panel of your washing machine. Pull the panel off your washing machine and set it aside.
Step 3. Pull the drive belt of the pulley wheel and motor shaft. Disconnect the motor electrical connectors. Use a nut driver to take out the mounting screws holding the motor assembly to your washing machine.
Step 4. Carefully pull the motor out of your washing machine and set it aside. Take your new drive motor out of its packaging. Put the motor into place and apply the mounting bolts with your nut-driver to secure it.
Step 5. Connect each electrical connector to its appropriate terminal on the new drive motor assembly. Fit the drive belt around the pulley wheel and motor shaft.
Step 6. Put the rear panel of your washing machine back on and apply all the screws with your Philips screwdriver to secure it.
Step 7. Connect the COLD and HOT water supply lines back to the inlet ports at the back of your washing machine. Plug your washing machine back to its power outlet and turn on the water valve on. Try running a wash cycle to see if the problem has been fixed.
6. Damaged Timer
Here’s how to replace a faulty timer in your Frigidaire washing machine…
How To Replace A Faulty Timer In Your Frigidaire Front Loader Washing Machine
Do the following to replace a faulty timer assembly in your Frigidaire front loader washing machine…
Step 1. Please ensure that you unplug your washing machine from its power outlet before starting any repairs in order to prevent electrocution.
Step 2. Turn the timer knob counter-clockwise and take it out of the control panel. Pull the timer dial off the control panel.
Step 3. Use a Philips screwdriver to remove the screws at the back of your washing machine holding the top panel. Slide the top panel backwards and lift it off your washing machine.
Step 4. Use your screwdriver to remove the screw holding the timer to the control panel. Pull the timer out of your washing machine and disconnect the electrical connectors.
Step 5. Set the old timer aside and take your new one out of its packaging. Connect the electrical connectors to the new timer assembly. Put the timer inside the washing machine and apply the screws with your Philips screwdriver to secure it.
Step 6. Push the timer knob and dial back into place on the control panel. Slide the top panel of your washing machine back on and apply the screws at the back with a Philips screwdriver.
Step 7. Plug your washing machine’s power cord back to its power outlet and try running a wash cycle to see if the problem has been solved.
How To Replace A Faulty Timer In Your Frigidaire Top Loader Washing Machine
Do the following to replace a damaged timer in your Frigidaire top loader washing machine…
Step 1. Unplug your washing machine’s power cord from its power outlet before starting this repair in order to prevent electrocution.
Step 2. Use your Philips screwdriver to take out the screws holding the rear cover of the control panel. Pull the panel off and set it aside.
Step 3. Use a small screwdriver to pull out the timer locking pin from the hole inside the timer. Pull the timer knob and knob dial off the control panel.
Step 4. Take out the timer screw from the control panel. Pull the timer assembly out of place and disconnect the electrical connectors from it. Take your new timer assembly out of its packaging.
Step 5. Connect the electrical connectors to the new timer and snap it into place on the control panel. Apply the screw on the control panel to secure the new timer. Use a small screwdriver to pull out the new timer locking pin.
Step 6. Push the timer knob and knob skirt back in place. Push the timer locking pin back in. Put the rear cover of the control panel back on and apply the screws with your Philips screwdriver to secure.
Step 7. Plug your washing machine back to its power outlet and try running wash cycle to see if the problem has been fixed.