Is your Frigidaire washing machine not washing? If so, you’ve come to the right place. This detailed guide outlines the causes of this issue and gives you steps on how to fix them. So, without wasting any more time, let’s get right to it…
Table of Contents
Frigidaire Washing Machine Not Washing — Solution
Is your Frigidaire washing machine not washing? If so, look for the following issues…
1. Damaged Agitator (Top Loaders Only)
Here’s how to replace a damaged agitator in your top loader washing machine…
Step 1. Open the lid of your washing machine. Pull the dispenser cup and cover off the agitator.
Step 2. Using a 1/2 inch socket wrench, remove the bolt holding the agitator to the washing machine. Pull the agitator out of the washing machine and set it aside.
Step 3. Take the new agitator assembly out of its packaging and install it in the washing machine. Apply the bolt with your socket wrench to secure it. Put the dispenser cup and cap back on.
Step 4. Plug your washing machine back to its power outlet and try running a wash cycle to see if the issue has been fixed.
2. Broken Drive Belt
Here’s what you’ll need to do to replace a broken drive belt in your Frigidaire washing machine…
How To Replace A Broken Drive Belt In Frigidaire Laundry Center Washing Machine
Do the following to replace a broken drive belt in your Frigidaire laundry center washing machine…
Step 1. Please ensure that you unplug your washing machine from its power supply and turn off the water valve before starting repair in order to prevent any chances of electrocution and water leakage.
Step 2. Pull your washing machine forwards to give you more working space. Use a screwdriver to remove the venting at the back of your washing machine. Unscrew the water supply hoses from the inlet ports at the back of your washing machine (make sure to keep a rag nearby in case water leaks out).
Step 3. Pull the drain hose out of the home drain. Put some tape over the lid of your washing machine to secure it. Tilt the washing machine backwards and lay it on the floor.
Step 4. Remove the screws holding the drive belt cover with a 10mm socket wrench. Pull the cover off the bottom of your washing machine and set it aside. Take the old drive belt out and take the new belt out of its packaging.
Step 5. Fit the drive belt around the pulleys (the grooved side of the belt should rest on the pulleys). Put the belt cover on and apply the bolts with your socket wrench to secure it.
Step 6. Lift your washing machine upright and peel the tape off the lid. Insert the drain hose back into the home drain.
Step 7. Connect the water supply hoses back to the inlet ports at the back of your washing machine (make sure to secure the connections in order to prevent water leakage).
Step 8. Connect the venting back to your washing machine. Move your washing machine back into place.
Step 9. Plug your washing machine back its power outlet and turn on the water supply valve. Try running a wash cycle to see if the issue has been fixed.
How To Replace A Broken Drive Belt In Frigidaire Top Loader Washing Machine
Here’s what you’ll need to do to replace a broken drive belt in your Frigidaire top loader washing machine…
Step 1. Please unplug your washing machine from its power outlet before starting this repair in order to prevent any chances of electrocution.
Step 2. Put some tape over the lid of your washing machine to secure it. Insert a putty knife under the main top panel of your washing machine to release the retaining clips. Lift the main top panel up and support it.
Step 3. Use your Philips screwdriver to take out the two screws at the bottom of the front panel. Lift the front panel up and pull it off the washing machine.
Step 4. Push the idler pulley inwards to release the tension on the drive belt. Pull the belt out and set it aside. Take your new drive belt out of its packaging. Push the idler pulley inwards and fit the new drive belt around the pulleys.
Step 5. Put the main front panel of your washing machine back on and apply the two screws at the bottom to secure it. Lower the main top panel of your washing machine and snap it into place.
Step 6. Peel the tape off the lid of your washing machine. Plug your washing machine back to its power outlet and try running a wash cycle to see if the problem has been fixed.
How To Replace A Broken Drive Belt In Frigidaire Front Loader Washing Machine
Do the following to replace a broken drive belt in your Frigidaire front loader washing machine…
Step 1. Ensure that you unplug your washing machine’s power cord from the power outlet and turn off the water supply valve before starting this repair in order to prevent electrocution and water leakage.
Step 2. Unscrew the COLD and HOT water supply lines from the inlet ports at the back of your washing machine (make sure to keep a rag nearby in case water spills out of the hoses ).
Step 3. Using your Philips screwdriver, take out the screws at the back of your washing machine holding the rear panel. Pull the panel off the washing machine and set it aside.
Step 4. Slowly rotate the drive pulley and pull the drive belt off the back of your washing machine. Take your new washing machine drive belt out of its packaging.
Step 5. Fit the new drive belt around the motor shaft and drive pulley (the grooved part of the belt should rest on the pulleys).
Step 6. Put the rear panel of your washing machine back on and apply the screws with your Philips screwdriver to secure it. Connect the two water supply hoses back to the inlet ports (ensure that you properly secure the connections in order to prevent water leaks).
Step 7. Turn on your washing machine’s water supply valve and plug the power cord back into the power outlet. Try running a wash cycle to see if the problem has been fixed.
3. Door Isn’t Locked (Front Loader Washing Machines)
Most front loader washing machine’s won’t start washing if the door isn’t properly locked. Make sure to shut your washing machine’s door firmly before starting a wash cycle.
If your washing machine door isn’t locking, you’ll need to replace the door lock assembly. Here’s how to do this…
Step 1. Unplug your washing machine’s power cord from the outlet before starting this repair in order to prevent any chances of electrocution.
Step 2. Open the door of your washing. Carefully peel the door seal away from the door opening (you don’t need to take the whole seal out). Use a Philips screwdriver to remove the two screws holding the door lock to the cabinet.
Step 3. Reach inside your washing machine and pull the door lock out. Disconnect the electrical connectors attached to the door lock assembly and set the old lock aside.
Step 4. Take your new door lock assembly out of its packaging. Connect the two electrical connectors to the new door lock. Put the lock inside your washing machine and apply the two screws to secure it.
Step 5. Carefully fit the door seal back around the door opening and close the washing machine’s door. Plug your washing machine’s power cord back to the power outlet and try running a cycle to ensure that the problem has been fixed.
4. Faulty Drive Motor
Your washing machine will not be able to start washing if the drive motor has failed. Here’s how to replace a failed drive motor in your Frigidaire washing machine…
How To Replace A Failed Drive Motor In Your Frigidaire Front Loader Washing Machine
Do the following to replace a failed drive motor in your Frigidaire front loader washing machine…
Step 1. Unplug your washing machine from its power supply and turn the water supply valve off before starting this repair in order to prevent any chances of water leakage and electrocution.
Step 2. Use a pair of pliers to unscrew the water supply hoses from the inlet ports at the back of your washing machine (we recommend keeping a rag nearby in case water spills out of the hoses).
Step 3. Using a Philips screwdriver, remove all the screws at the back of your washing machine holding the rear panel. Pull the panel off the washing machine and set it aside.
Step 4. Rotate the drive pulley and pull the drive belt off the back of the washing machine. Disconnect the electrical connectors from the drive motor.
Step 5. Use a socket wrench to remove the mounting screws holding the drive motor to the base of your washing machine. Pull the drive motor out of place and set it aside.
Step 6. Take your new washing machine drive motor out of its packaging. Install the drive motor at the bottom of the drum and apply the mounting bolts with your socket wrench to secure it. Connect the electrical connectors to the new drive motor.
Step 7. Fit the drive belt back around the drive pulley and motor shaft. Fit the rear panel of your washing machine back into place and apply the screws with your Philips screwdriver to secure it.
Step 8. Connect the COLD and HOT water supply lines to the inlet ports at the back of your washing machine (in order to prevent water leaks, make sure to secure the connections properly).
Step 9. Turn on your washing machine’s water supply valve and plug the power cord back into the power outlet. Test the washing machine by running a wash cycle.
How To Replace A Failed Drive Motor In Your Frigidaire Top Loader Washing Machine
Here’s what you’ll need to do to replace a faulty motor in your Frigidaire top loader washing machine…
Step 1. Disconnect your washing machine’s power cord from the power outlet before starting this repair in order to prevent electrocution. Put some tape over the lid of your washing machine to secure it.
Step 2. Insert a putty knife underneath your washing machine’s main top panel to release the two retaining clips. Lift the main top panel of your washing machine and support it.
Step 3. Using a Philips screwdriver, remove the two screws at the bottom of the front panel. Pull the tub forwards and unhook the two suspension springs.
Step 4. Use your Philips screwdriver to remove the screws holding the motor shield to the tub. Disconnect the electrical connectors attached to the capacitor and set the motor shield aside.
Step 5. Unscrew the front mounting screw. Insert a wooden plank under the tub and pry it up slightly. Insert the screw into the hole on the tub above the mounting base.
Step 6. Disconnect the electrical connector from the drive motor. Push the idler pulley inwards and pull the drive belt off. Use a socket wrench to remove the mounting nuts holding the drive motor to the base of your washing machine.
Step 7. Pull the drive motor out of your washing machine and set it aside. Take your new washing machine drive motor out of its packaging.
Step 8. Install the new drive motor in your washing machine and apply the mounting bolts to secure it. Connect the electrical connector to the new drive motor.
Step 9. Push the idler pulley inward and fit the drive belt back around the pulleys. Insert the wooden plank under the tub again and pull the support bolt out.
Step 10. Lower the drum and insert the mounting bolt into its proper hole. Apply the bolt with your socket wrench to secure it.
Step 11. Connect the two electrical connectors to capacitor on the motor shield. Put the motor shield in place and apply the two screws to secure it.
Step 12. Hook the two suspension springs back to the drum. Put your washing machine’s main front panel back on and apply the two screws at the bottom with your Philips screwdriver to secure it.
Step 13. Lower the main top panel of your washing machine and snap it into place. Peel the tape off the lid of your washing machine. Plug your washing machine back to its power outlet and try washing a wash cycle to see if the issue has been resolved.
Check out these other articles…
Washing Machine Overfilling/Overflowing [Problems Solved]
Washing Machine Agitates But… [Various Problems Solved]
Frigidaire Washing Machine Seal/Gasket [How To]
Frigidaire Washing Machine Pump [Problems & Solutions]
Frigidaire Washing Machine Blinking Lights [How To Fix]
How To Replace A Failed Drive Motor In Your Frigidaire Laundry Center Washing Machine
Do the following to replace a failed drive motor in your Frigidaire laundry center washing machine…
Step 1. Turn off your washing machine’s water supply valve and unplug the power cord before starting this repair in order to prevent electrocution and water leakage.
Step 2. With the help of another person, pull your washing machine forwards. Use your screwdriver to remove the venting at the back of the machine.
Step 3. Using a pair of pliers, unscrew the water supply lines from the inlet ports at the back of your washing machine (it is advised that you keep a towel nearby to clean any water leaks).
Step 4. Pull the drain hose out of your home drain. Apply some tape to the lid of your washing machine to secure it. With the help of another person, tilt your washing machine backwards and lay it on the floor.
Step 5. Use a 10mm socket wrench to remove the bolts holding the drive belt cover. Pull the cover off and set it aside. Detach the drive belt from the pulleys.
Step 5. Disconnect the electrical connectors from the drive motor. Remove the mounting screws holding the motor to the base of your washing machine. Pull the drive motor off your washing machine and set it aside.
Step 6. Take your new drive motor assembly out of its packaging. Place the drive motor at the base of your washing machine and apply the mounting bolts to secure it. Connect the electrical connectors to the new drive motor.
Step 6. Fit the drive belt around the new motor shaft. Put the drive belt cover back in place and secure it by applying the mounting bolts.
Step 7. Lift the washing machine upright and peel the tape off the lid. Insert your drain hose into the home drain. Connect the two water supply lines back to the inlet ports at the back of your washing machine (make sure to properly secure the connections in order to prevent leaks).
Step 8. Reattach the venting to the back of your washing machine. Push your washing machine back into place. Turn on your washing machine’s water valve and plug the power cord back in. Try running a wash cycle to see if the problem has been solved.
5. Damaged Transmission Assembly
Here’s what you’ll need to do to replace a damaged transmission assembly in your Frigidaire washing machine…
How To Replace Damaged Transmission Assembly In Frigidaire Laundry Center Washing Machine
Do the following to replace a damaged transmission assembly in your Frigidaire laundry center…
Step 1. Please ensure that you turn off your washing machine’s water supply valve and unplug the power cord from the outlet before starting this repair in order to prevent electrocution and water leakage.
Step 2. With the assistance of another person, pull your washing machine forwards to give you more working space. Use your screwdriver to detach the venting from the back your washing machine.
Step 3. Use a pair of pliers to unscrew the HOT and COLD water supply lines from the inlet ports at the back of your washing machine (we recommend keeping a rag nearby in case water spills out).
Step 4. Pull your washing machine’s main drain hose out of your home drain. Insert a putty knife underneath your washing machine’s main top panel to release the two retaining clips.
Step 5. Lift the main top panel up and disconnect the lid lock electrical connector from underneath it. Slide the top panel forwards and lift it off your washing machine.
Step 6. With the help of another person, tilt the washing machine backwards slightly and place something like a block of wood underneath the front. Use your Philips screwdriver to remove the screws at the bottom of the main front panel.
Step 7. Take the support out from under the machine and lower your washer back to the floor. Lift the main front panel of your washing machine slightly and pull it out.
Step 8. Remove the four suspension springs on the tub cover. Go to the back of your washing machine. Using a 5/16 inch nut driver, remove the mounting screws holding the main control board mounting plate to the back of your washing machine.
Step 9. Pry the plate off the back of your washing machine using a flat-blade screwdriver. Pull the control board assembly out of place. Disconnect the electrical connectors for the tub components on the control board. Cut the zip-tie holding the tub component wires to the board.
Step 10. Pass the tub component electrical connectors through the opening in the panel. Put the control board and mounting plate back in place.
Step 11. Go to the front of the machine. Use a 5/16 inch wrench to take out the bolt holding the grounding wire to the cabinet.
Step 12. With the assistance of another person, carefully tilt the washing machine backwards and lat it on the floor.
Step 13. Place a block of wood under the drum. Pull the tub towards the top of the cabinet to get more slack on the suspension rods. Detach each of the four suspension rods from the tub.
Step 14. Using a pair of pliers, press the clamp on the hose attache to the drain pump and slide it out of place. Disconnect the outlet hose from the drain pump (some water will leak out of the hose).
Step 15. Pull the air pressure hose off the tube at the side of the drum. Carefully pull the drum assembly through the opening at the bottom of the cabinet.
Step 16. Set the tub assembly upright. Use a flat-blade screwdriver to pry the tub cover off the tub assembly. Remove the agitator cap from the agitator assembly. Using a 10mm socket with an extension, remove the agitator bolt. Pull the agitator out of your washing machine and set it aside.
Step 17. Using a 6mm Allen key, remove the two bolts holding the tub mounting hub to the transmission shaft. Carefully lift out the inner tub assembly and set it aside.
Step 18. Turn the outer tub assembly upside down and lay it on the floor. Using your 10mm socket wrench, remove the bolts holding the belt cover to the tub. Pull the cover off and set it aside.
Step 19. Slowly rotate the drive belt and detach it from the two pulleys. Disconnect the electrical connector of the clutch actuator. Use your socket wrench to remove the two bolts holding the actuator to the tub. Pull the actuator off the washing machine and set it aside.
Step 20. Using a pair of needle-nosed pliers, release the wire retainers from the transmission plate. Use a 3/8 inch socket wrench to take out the eight screws holding the transmission assembly to the outer tub. Pull the transmission assembly out of the tub and set it aside.
Step 21. Take your new washing machine transmission assembly out of its packaging. Use a 17mm socket wrench to take out the bolt holding the pulley wheel to the old transmission assembly. Transfer the pulley wheel to the new transmission assembly and apply the bolt to secure it.
Step 22. Insert the new transmission assembly inside your washing machine. Apply the mounting bolts with your socket wrench to secure it. Snap the wire retainers into the holes on the new transmission plate.
Step 23. Put the clutch actuator back in place and apply the mounting bolts to secure. Connect the electrical connector to the clutch actuator.
Step 24. Fit the drive belt around the motor pulley and the transmission pulley. Put the belt cover back on and apply the screws with your 10mm socket wrench to secure it.
Step 25. Turn the outer tub assembly over. Carefully lower the inner tub into the outer tub. Secure the mounting hub to the shaft using your 6mn Allen key.
Step 26. Put the agitator bolt into your socket wrench with an extension. Insert the bolt into the hole in the agitator. Carefully place the agitator back inside your washing machine and tighten the bolt to secure it. Put the agitator cap back on.
Step 27. Snap the tub cover back into place. Lift the tub assembly back inside your washing machine’s cabinet. Connect the air pressure hose back to the port at the side of the drum.
Step 28. Connect the drain outlet hose to the drain pump assembly and slide the retaining clamp back in place to secure it.
Step 29. Insert the four suspension rods into the openings at the side of the tub and snap them into place. Remove the block of wood from your washing machine’s cabinet.
Step 30. With the help of another person, lift your washing machine upright. Go to the back of your washing machine.
Step 31. Use your flat-blade screwdriver to pry the control board plate off the back of your washing machine. Pass the tub component wire connectors through the opening and connect them to the control board. Secure the wires in the retainers.
Step 32. Snap the control board housing into place and apply the screws with your nut driver to secure it.
Step 33. Connect the four suspension rod support springs back to the tub. Put the main front panel of your washing machine back on and use your Philips screwdriver to apply the screws.
Step 34. Connect the lid lock electrical connector back to the top panel. Snap the top panel of your washing machine back in place.
Step 35. Insert your washing machine’s main drain hose back into the home drain. Connect the COLD and HOT water supply lines back to the inlet ports at the back of your washing machine (make sure you secure the connections properly so water doesn’t leak out).
Step 36. Reattach the venting to the back of your washing machine. Move your washing machine back into place.
Step 37. Turn on your washing machine’s water supply valve and plug the power cord back into the outlet. Make sure the washing machine is working properly by running a wash cycle.
How To Replace Damaged Transmission Assembly In Frigidaire Top Loader Washing Machine
Do the following to replace a damaged transmission assembly in your Frigidaire top loader washing machine…
Step 1. Please make sure to unplug your washing machine’s power cord and turn the water supply valve off before starting this repair in order to prevent water leaks or electrocution.
Step 2. Apply some tape to the lid of your washing machine to secure it. Insert a putty knife under the main top panel of your washing machine to release the two retaining clips. Lift the top panel up and support it.
Step 3. Use your Philips screwdriver to remove the screws at the bottom of the front panel. Lift the front panel upwards and pull it off your washing machine.
Step 4. Push the idler pulley inwards to give the drive belt slack. Pull the drive belt out of your washing machine and set it aside.
Step 5. Pull the dispenser cup and cover off the agitator inside the drum. Use a socket wrench to take out the bolt holding the agitator to your washing machine. Lift the agitator out of the drum and set it aside.
Step 6. Release the air pressure tube from the retainer on the tub cover. Pry the tub cover off using a flat-blade screwdriver. Using a 1/2 inch socket, take out the trunnion mounting bolts. Carefully lift the inner tub assembly out of your washing machine.
Step 7. Push the brass ring on the transmission shaft down to release it from the gasket. Pull the brass ring and gasket off the shaft and set them aside. Use your Philips screwdriver to remove the two screws holding the motor shield to the tub. Set the motor shield and capacitor aside.
Step 8. Use a pair of pliers to release the clamp on the outlet hose attached to the drum and slide the clamp out of place. Disconnect the drain hose from the tub (keep a rag nearby in case water spills out).
Step 9. Use your socket wrench to take out the three mounting bolts holding the outer tub the base. Lift the outer tub off the transmission shaft and set it aside.
Step 10. Pull the spacer off the transmission shaft and set it aside. Using a 3/8 inch socket wrench, remove the screw holding the transmission pulley. Take the pulley out and set it aside.
Step 11. Use your socket wrench to take out the bolts holding the transmission bearing block to the mounting plate. Lift the transmission assembly off your washing machine and set it aside.
Step 12. Take your new washing machine transmission assembly out of its packaging. Unscrew the bolts on the new transmission. Position the new transmission assembly inside your washer’s cabinet and apply the bolts to secure it.
Step 13. If the new transmission kit doesn’t come with a new drive block, unscrew the block at the top of the old transmission and transfer it to the new one. Put the transmission pulley on the drive shaft and apply the bolt to secure it.
Step 14. Put the space onto the new transmission shaft. Lower the outer tub assembly onto the shaft and apply the three mounting bolts to secure it to the base. Connect the air pressure hose back to the port at the side of the tub.
Step 15. Connect the drain outlet hose back to the port under the tub and secure it by sliding the retaining clamp in place. Put the capacitor and motor shield back in place and apply the two screws with your Philips screwdriver to secure it.
Step 16. Slide the gasket and brass ring onto the transmission shaft and press down to secure. Lower the inner tub onto the shaft and apply the bolts on the trunnion block to secure it.
Step 17. Snap the tub cover back onto the tub. Secure the air pressure tube in the retainer on the tub cover. Put the agitator back inside the washing machine and apply the bolt to secure it.
Step 18. Put the dispenser cover and cup back onto the agitator. Fit the drive belt around the two pulleys under the machine.
Step 19. Snap the main front panel of your washing machine back on and apply the two screws at the bottom to secure it. Lower the main top panel of your washing machine and snap it into place. Peel the tape off the lid of your washing machine.
Step 20. Plug your washing machine’s power cord back into the power outlet and try running a wash cycle to ensure that everything is working properly.
6. Failed Motor Control Board
Here’s what you’ll need to do to replace a failed motor control board in your Frigidaire washing machine…
How To Replace Failed Motor Control Board In Frigidaire Top Loader Washing Machine
Do the following to replace a failed motor control board in your Frigidaire top loader washing machine…
Step 1. Unplug your washing machine’s power cord from the power outlet before starting this repair in order to prevent electrocution.
Step 2. Use your Philips screwdriver to remove the two screws on the main front panel of your washing machine. Pull the panel downwards and lift it off your washing machine.
Step 3. Use a screwdriver to take out the screws holding the motor control board to the base of your washing machine. Pull the control board out of place and disconnect the electrical connectors (make sure to note where each connector goes).
Step 4. Take your new washing machine control board out of its packaging and connect each electrical connector to its appropriate terminal. Mount the new control board in your washing machine and apply the screws to secure it.
Step 5. Snap the main front panel of your washing machine back in place and apply the two screws at the bottom to secure it. Plug your washing machine’s power cord back into the outlet and try running a wash cycle to see if the problem has been fixed.
How To Replace Failed Motor Control Board In Frigidaire Front Loader Washing Machine
Here’s what you’ll need to do to replace a failed motor control board in your Frigidaire front loader washing machine…
Step 1. Make sure to unplug your washing machine from its power outlet before starting this repair in order to prevent any chances of electrocution.
Step 2. Use your Philips screwdriver to remove the screws holding the rear access panel of your washing machine. Pull the panel off your washing machine and set it aside.
Step 3. Slowly rotate the drive belt and detach it from the pulleys. Disconnect the grounding wire and electrical connectors from the drive motor. Use a socket wrench to take out the bolts holding the drive motor to the bottom of the drum.
Step 4. Let the motor drop down and pull it out of your washing machine. Use a pair of pliers to release the retainer holding the electrical connector to the motor assembly.
Step 5. The motor control board will be mounted on the right side of the cabinet. Disconnect the nearest electrical connector on the control board. Use your Philips screwdriver holding the grounding wire and mounting screw to the base of your washing machine.
Step 6. Pull the motor control board out of place and turn it over. Disconnect all the remaining electrical connectors from the motor control board. Set the motor control board aside and take the new control board out of its packaging.
Step 7. Remove the mounting base from the old motor control board and transfer it to the new one. Connect all the electrical connectors to the new motor control board.
Step 8. Mount the new control board inside the washing machine. Apply the screw to secure the grounding wire and control board to the base of your washing machine.
Step 9. Fit the drive motor back in place at the bottom of your washing machine and apply the mounting bolts with your socket wrench to secure it. Connect each electrical connector to its appropriate terminal on the drive motor.
Step 10. Fit the drive belt around the pulleys at the back of your washing machine. Put the rear panel of your washing machine back on and apply all the screws with your Philips screwdriver.
Step 11. Plug your washing machine’s power cord back into the power outlet and try running a wash cycle to see if the problem has been fixed.
Frigidaire Washing Machine Not Rinsing — How To Fix
Is your Frigidaire washing machine not rinsing? If so, here are the issues to look for…
1. Door Isn’t Locked (Front Loader Washers Only)
Your front loader washing machine will not start rinsing if the door isn’t properly locked. Ensure that you firmly shut your washing machine’s door before starting a wash cycle.
2. Blocked Water Inlet Screens
Here’s what you’ll need to do to clean a blocked water inlet screen in your Frigidaire washing machine…
Step 1. Turn off your washing machine’s water supply valve and unplug the power cord from the outlet before starting this repair in order to avoid electrocution and water leakage.
Step 2. Use a pair of pliers to unscrew the COLD and HOT water supply lines from the inlet ports at the back of your washing machine (you should keep a towel nearby in case water spills out of the hoses).
Step 3. Use a pair of needle-nosed pliers to pull out the little mesh filters inside each of the water inlet ports. Take the filters to a sink and clean out any dirt that may have accumulated in it.
Step 4. Once you’ve cleaned the filters properly, put them back in place. Reconnect the water supply hoses to the back of your washing machine (tighten them properly to avoid water leaks).
Step 5. Turn on your washing machine’s water supply valve and plug the power cord back into the outlet. Make sure your washing machine is working properly by running a wash cycle.
3. Water Level Sensor Has Failed
Here are the steps you’ll need to take to replace a failed water level sensor in your Frigidaire washing machine…
How To Change Failed Water Level Sensor In Frigidaire Front Loader Washing Machine
Do the following to replace a defective water level sensor in your Frigidaire front loader washing machine…
Step 1. Please ensure that you unplug your washing machine’s power cord from the power outlet before starting this repair in order to prevent any chances of electrocution.
Step 2. Using your Philips screwdriver, remove the screws at the back of your washing machine securing the top panel. Slide the panel backwards and lift it off your washing machine.
Step 3. The water level sensor will be mounted on the washing machine’s cabinet. Disconnect the electrical connector attached to the sensor. Use a pair of pliers to press the clamp on the tube attached to the sensor and slide the clamp out of place.
Step 4. Disconnect the tube from the water level sensor. Press the tabs on the sensor to release it from the cabinet and set it aside.
Step 5. Take your new washing machine water level sensor out of its packaging. Connect the tube to the new sensor and slide the retaining clamp in place to secure it. Connect the electrical connector to the new water level sensor.
Step 6. Snap the new sensor into the cabinet. Slide your washing machine’s main top panel back on and apply the screws at the back with your Philips screwdriver to secure it.
Step 7. Plug your washing machine’s power cord back into the outlet and try running a wash cycle to see if the problem has been fixed.
How To Change Failed Water Level Sensor In Frigidaire Top Loader Washing Machine
Do the following to replace a faulty water level sensor in your Frigidaire top loader washing machine…
Step 1. Ensure that your washing machine’s power cord is unplugged from the outlet before starting this repair (this will prevent any chances of electrocution.
Step 2. Use a Philips screwdriver to remove the screws holding the rear access cover of the control panel. Pull the cover off and set it aside. Pull the pressure switch knob off the control panel (if needed, use some string).
Step 3. Use your screwdriver to remove the screw holding the pressure switch to the control panel. Pull the water level sensor out of place and disconnect the electrical connectors attached to it. Disconnect the air pressure tube from the sensor and set it aside.
Step 4. Take your new washing machine water level sensor out of its packaging. Connect the air pressure tube to the new sensor and connect the two wire connectors.
Step 5. Mount the new water level sensor on your washing machine’s control panel and apply the screw with your Philips screwdriver to secure it. Push the water level sensor knob back into place.
Step 6. Put the rear access cover of the control panel back on and apply the screws using your Philips screwdriver to secure it. Plug your washing machine’s power cord back into the outlet and try running a wash cycle to see if the problem has been fixed.
How To Change Failed Water Level Sensor In Frigidaire Laundry Center Washing Machine
Here’s what you’ll need to do to replace a failed water level sensor in your Frigidaire laundry center washing machine…
Step 1. Before starting this repair, make sure to unplug your washing machine’s power cord from the power outlet in order to prevent electrocution.
Step 2. Insert a tool such as a putty knife under the main top panel of your washing machine to release the two retaining clips. Lift the top panel slightly and disconnect the lid lock electrical connector. Lift the front panel off your washing machine and set it aside.
Step 3. With the help of another person, tilt your washing machine backwards slightly and place a block of wood underneath the front panel to wedge it. Use your Philips screwdriver to take out the screws at the bottom of the front panel.
Step 4. Remove the support and carefully lower your washing machine. Push the front panel downwards and pull it off your washing machine.
Step 5. The water level sensor will be mounted on the right side of the cabinet. Press the tabs on the sensor to release it from the mounting bracket.
Step 6. Disconnect the electrical connector from the water level sensor. Using a pair of needle-nosed pliers, detach the air pressure tube from the level sensor. Set the sensor aside and take your new one out of its packaging.
Step 7. Connect the air pressure tube to the new water level sensor. Attach the electrical connector to the sensor.
Step 8. Mount your new sensor on the washing machine’s cabinet. Snap your washing machine’s main front panel back on. Tilt your washing machine backwards again and place the support underneath it.
Step 9. Apply the two screws at the bottom of the front panel to secure it. Take the support out and carefully lower your machine.
Step 10. Connect the lid lock electrical connector back to the top panel. Snap the top panel into place. Plug your washing machine’s power cord into the power outlet and try running a wash cycle to see if the problem has been fixed.
4. Water Inlet Valve Has Failed
Follow the steps below to replace a damaged water inlet valve in your Frigidaire washing machine…
How To Replace A Failed Water Inlet Valve In Frigidaire Laundry Center Washing Machine
To replace a faulty water inlet valve in your Frigidaire laundry center washing machine, here’s what you’ll need to do…
Step 1. Turn off your washing machine’s water supply valve and unplug the power cord from the outlet before starting this repair in order to prevent electrocution or water leakage.
Step 2. Get another person to help you move your washing machine forwards a bit (this provides more working space). Use your Philips screwdriver to detach the venting from the back of your machine.
Step 3. Pull your washing machine’s drain hose out of your home drain. Use a pair of pliers to unscrew the COLD and HOT water supply hoses from the inlet ports at the back of your washing machine (make sure to keep a rag nearby in case water spills out).
Step 4. Use a Philips screwdriver to remove the screw holding the water inlet valve to the cabinet. Push the valve inwards.
Step 5. Insert a tool such as a putty knife under the main top panel of your washing machine to release the retaining clips. Lift the main top panel slightly and disconnect the lid lock electrical connector from it.
Step 6. Pull the main top panel off your washing machine and set it aside. Reach inside the cabinet and pull the water inlet valve assembly out.
Step 7. Use a pair of pliers to press the clamps on the hoses attached to the inlet valve and slide them out of plae. Disconnect the hoses from the water inlet valve assembly (some water will spill out).
Step 8. Disconenct the solenoid wire connectors from the water inlet valve assembly. Set the water inlet valve assembly aside and take the new valve out of its packaging.
Step 9. Connect the hoses to their appropriatet ports on the new water inlet valve and slide the retaining clamps in place to secure them. Connect each solenoid wire connector to its corresponding terminal on the new valve.
Step 10. Insert the new valve into the opening on the cabinet. Go to the back of your washing machine and apply the screw with your Philips screwdriver to secure the new valve.
Step 11. Connect the electrical connector back to the lid lock on the main top panel. Snap the top panel onto your washing machine. Connect the COLD and HOT water supply lines to the inlet ports at the back of your washing machine (ensure that you secure the connections properly in order to avoid water leaks).
Step 12. Insert the drain hose into your home drain and reattach the venting to the washer. Turn on your washing machine’s water supply valve and plug the power cord back into the outlet. Make sure the washing machine is working properly by running a wash cycle.
How To Replace A Failed Water Inlet Valve In Frigidaire Top Loader Washing Machine
Do the following to change a faulty water inlet valve in your Frigidaire top loader washing machine…
Step 1. Shut off your washing machine’s water supply valve and unplug the power cord from the outlet before starting this repair in order to prevent electrocution or water leakage.
Step 2. Use a pair of pliers to unscrew the two water supply hoses at the back of your washing machine (make sure to have a rag nearby in case water spills out of the hoses).
Step 3. Use your screwdriver to remove the two screws at the bottom of your washing machine’s front panel. Slide the panel downwards and pull it off your washing machine.
Step 4. Use your screwdriver to remove the screws holding the top panel to the sides. Open the lid of your washing machine.
Step 5. Using a flat-blade screwdriver, release the lid lock assembly from the top panel. Take out the bleach dispenser cover. Use your screwdriver to take out the screw holding the dispenser to the top panel.
Step 6. Release the dispenser from the main top panel by pressing the tabs on it. Lift the entire main top panel and support it.
Step 7. Use your screwdriver to remove the screw at the back of your washing machine holding the water inlet valve assembly to the cabinet. Push the valve assembly inwards to release it from the cabinet.
Step 8. Disconnect all the solenoid wire connectors attached to the water inlet valve assembly (make sure to note where each connector goes). Using a pair of pliers, press the clamps on the hoses attached to the water inlet valve and slide them out of place. Disconnect the hoses from the valve (some water may leak out).
Step 9. Set the old water inlet valve aside and take the new valve out of its packaging. Connect the two hoses to their appropriate ports on the new water inlet valve assembly and secure them by sliding the retaining clamps into place.
Step 10. Connect each solenoid wire connector to its appropriate terminal on the new water inlet valve. Insert the new valve into the opening at the back of the washing machine and apply the mounting screw to secure it.
Step 11. Lower the main top panel of your washing machine and snap it into place. Snap the dispenser back into the top panel and apply the screw with your Philips screwdriver to secure it. Put the cover back into the dispenser.
Step 12. Snap the lid lock assembly back into the main top panel. Secure the top panel to the sides of the washing machine by applying the mounting screws.
Step 13. Snap the main front panel of your washing machine back into place and apply the two screws at the bottom to secure it.
Step 14. Connect the two water supply hoses to the inlet ports at the back of your washing machine (tighten the connections properly in order to prevent water leaks.
Step 15. Turn on your washing machine’s water supply valve and plug the power cord back into the outlet. Try running a wash cycle to make sure the machine works properly.
How To Replace A Failed Water Inlet Valve In Frigidaire Front Loader Washing Machine
Here are the steps you’ll need to take to replace a failed water inlet valve in your Frigidaire front loader washing machine…
Step 1. Shut off your washing machine’s water supply valve and unplug the power cord from the power outlet before starting this repair in order to prevent electrocution or water leakage.
Step 2. Unscrew the HOT and COLD water supply hoses from the inlet ports at the back of your washing machine (we recommend keeping a rag nearby in case water spills out of the hoses).
Step 3. Use a Philips screwdriver to take out the screws at the back of your washing machine holding the main top panel. Slide the top panel backwards a few inches and lift it off your washing machine.
Step 4. Using a screwdriver, take out the two mounting screws at the back of your washing machine holding the water inlet valve to the cabinet. Pull the valve assembly out of your washing machine’s cabinet.
Step 5. Disconnect the solenoid wire connectors attached to the water inlet valve assembly (ensure that you note where each connector goes).
Step 6. Use a pair of pliers to press the clamp on the inlet hose attacehd to the valve assembly and slide the clamp out of place. Disconnect the inlet hose from the valve (some water may leak out).
Step 7. Set the water inlet valve aside and take your new washing machine water inlet valve out of its packaging. Connect the inlet hose to the new water inlet valve and slide the retaining clamp into place to secure it.
Step 8. Connect each electrical connector to its appropriate terminal on the new water inlet valve. Mount the new valve inside your washing machine and apply the screws at the back to secure it to the cabinet.
Step 9. Slide your washing machine’s top panel back on and apply the screws at the back with a Philips screwdriver to secure it. Connect the water supply hoses to the ports at the back of your washing machine (make sure the connections are secured properly so water doesn’t leak out).
Step 10. Turn on your washing machine’s water supply valve and plug the power cord back into the power outlet. Make sure the appliance is working properly by running a wash cycle.
5. Main Control Board Failure
To replace a failed control board in your Frigidaire washing machine, here are the steps you’ll need to take…
How To Replace Damaged Control Board In Frigidaire Top Loader Washing Machine
Take the following steps to replace your Frigidaire top loader washing machine’s damaged control board…
Step 1. Please make sure to unplug your washing machine’s power cord from its power outlet before starting this repair in order to avoid electrocution.
Step 2. Push a small screwdriver into the holes on the rear access cover of the control panel. Pry the control panel off the housing and lay it on the lid of your washing machine.
Step 3. Take note of the electrical connectors attached to the control board and disconnect each one.
Step 4. Use a Philips screwdriver to remove the screws holding the control board to the panel. Set the old control board aside and take the new board out of its packaging.
Step 5. Mount the new control board on the panel and apply the screws with your Philips screwdriver to secure it. Connect each electrical connector to its appropriate terminal on the new control board.
Step 6. Lift the control panel and snap it back into the housing. Plug your washing machine’s power cord back into the power outlet and run a wash cycle to see if the problem has been fixed.
How To Replace Damaged Control Board In Frigidaire Front Loader Washing Machine
Here’s how to change a faulty control board in your Frigidaire front loader washing machine…
Step 1. Ensure that your washing machine is unplugged from its power supply before you start this repair (this will prevent electrocution and water leakage).
Step 2. Go to the back of your washing machine and use a Philips screwdriver to loosen the screws holding the top panel in place. Slide the top panel backwards about an inch or so, and lift it off your washing machine.
Step 3. Pull out the detergent drawer and press the tab inside it to take it out of the washing machine completely. Use your Philips screwdriver to remove the three screws beside the detergent drawer housing.
Step 4. Take out the two screws on each top corner of the control panel. Using a flat-blade screwdriver, pry the tabs on the control panel holding it to the cabinet.
Step 5. Disconnect all the wire harnesses attached to the board on the control panel (ensure that you note where each connector goes). Use your Philips screwdriver to remove the screws holding the control board to the control panel.
Step 6. Pull the board off the panel. Use a flat-blade screwdriver to pry the two halves of the control board apart. Using a pair of needle-nosed pliers, release the control board wire retainers from the lower half of the board. Snap the two halves of the control board back together.
Step 7. Use a flat-blade screwdriver to pry off all the buttons and knobs on the control board. Take your new board out of its packaging and transfer the buttons to it.
Step 8. Pull the screen cover off the old control board. Use your flat-blade screwdriver to pry the indicator screen from the old board and snap it into the new board. Put the screen cover onto the new board.
Step 9. Snap all the wire retainers into the holes at the back of the new control board. Place the new control board on the control panel and apply all the screws with your Philips screwdriver to secure it.
Step 10. Connect each electrical connector to its appropriate terminal on the new control board. Snap the control panel onto the front of your washing machine and apply the two screws on the top corners.
Step 11. Use your Philips screwdriver to apply the three screws beside the detergent drawer housing. Slide the detergent drawer into place.
Step 12. Snap your washing machine’s top panel back on and apply the screws at the back using a Philips screwdriver to secure it. Plug your washing machine’s power cord back into the outlet and see if the problem has been fixed by running a wash cycle.
How To Replace Damaged Control Board In Frigidaire Laundry Center Washing Machine
Here’s what you’ll need to do to replace a damaged control board in your Frigidaire laundry center washing machine…
Step 1. Shut off your washing machine’s water supply valve and unplug the power cord from the outlet before starting this repair in order to prevent water leaks or electrocution.
Step 2. Get someone to help you move the washing machine forwards a bit (this will give you more working space). Pull the drain hose out of your home drain.
Step 3. Use a pair of pliers to unscew the two water supply hoses from the inlet ports at the back of your washing machine (make sure to have a rag nearby in case water spills out).
Step 4. Use a screwdriver to detach the venting from the back of your washing machine. Remove the screws holding the control board moutning plate to the back of your washing machine.
Step 5. Pry the control board plate off the washing machine using a flat-blade screwdriver. Pull the control board assembly out of the housing.
Step 6. Use a Philips screwdriver to remove the screws holding the control board to the mounting plate. Detach the plate from the housing by prying the retaining tabs with a Philips screwdriver.
Step 7. Detach the control board wire retainers from the board assembly using a pair of pliers. Take note of where each electrical connector is attached to the board and disconnect each one.
Step 8. Set the control board aside and take your new board out of its packaging. Connect each electrical connector to its appropriate terminal on the new control board.
Step 9. Secure the wire retainers in the holes on the new control board. Snap the mounting plate onto the new control board and apply the two screws with your Philips screwdriver to secure it.
Step 10. Push the control board assembly into the housing and use your Philips screwdriver to apply the mounting screws.
Step 11. Insert your drain hose back into the home drain. Reattach the COLD and HOT water supply hoses to the inlet ports at the back of your washing machine (ensure that you secure the connections properly so water doesn’t leak out).
Step 12. Move your washing machine back into place. Plug your washing machine’s power cord back into the power supply and turn the water supply valve back on. Try running a wash cycle to see if the problem has been fixed.
6. Timer Failure
Here’s what you’ll need to do to replace a failed timer in your Frigidaire washing machine…
How To Replace Damaged Timer In Frigidaire Laundry Center Washing Machine
Do the following to replace a damaged timer in your Frigidaire laundry center washing machine…
Step 1. Please make sure to unplug your washing machine’s power cord from the power outlet before starting this repair in order to prevent electrocution.
Step 2. Use your Philip screwdriver to take out the screws holding the panel directly under the control panel. Pull the panel off your washing machine and set it aside.
Step 3. Use your screwdriver to remove the mounting screws holding the control panel to the dryer unit. Detach the control panel from the machine.
Step 4. Use a pair of needle-nosed pliers to pull out the locking pin inside the timer. Pull the timer knob and skirt off the control panel. Use your Philips screwdriver to remove the screw beside the timer shaft.
Step 5. Disconnect the electrical connector attached to the timer. Slide the timer assembly to the left a bit and pull it off the control panel.
Step 6. Take your new washing machine timer assembly out of its packaging. Snap the new timer onto the control panel and connect the electrical connector to it.
Step 7. Apply the mounting screw beside the timer shaft to secure it. Snap the timer knob and skirt back into the contol panel. Use your pliers or a small screwdriver to push the new timer locking pin inwards.
Step 8. Snap the control panel onto your washing machine and secure it by applying the two mounting screws. Put the lower access panel back in place and apply the screws with your Philips screwdriver.
Step 9. Plug your washing machine’s power cord back into the outlet and try running a wash cycle to make sure everything is working properly.
How To Replace Damaged Timer In Frigidaire Top Loader Washing Machine
Here are the steps you’ll need to take to replace a faulty timer in you top loader Frigidaire washing machine…
Step 1. Unplug your washing machine’s power cord from the power outlet before starting this repair in order to prevent any chances of electrocution.
Step 2. Use a Philips screwdriver to remove the screws at the back of your washing machine holding the rear access panel. Pull the panel off your washing machine and set it aside.
Step 3. Insert a small screwdriver or a needle-nosed plier into the little hole inside the timer and pull out the locking pin.
Step 4. Pull the timer knob and skirt off the control panel and set them aside. Use your screwdriver to take out the screw on the control panel holding the timer assembly.
Step 5. Slide the timer assembly towards your right and pulll it off the control panel Disconnect the electrical connector attached to the timer and set the timer aside.
Step 6.Take your new washing machine timer assembly out of its packaging. Connect the electrical connector to the new timer assembly. Install the new timer assembly in your washing machine and slide it sideways to lock it in.
Step 7. Apply the mounting screw on the control panel to secure the new timer. Place the timer knob and skirt back on the control panel. Push the new timer locking pin inwards.
Step 8. Put the rear access cover of the control panel back on and apply the screws with your Philips screwdriver to secure it. Plug your washing machine back into its power supply and try running a wash cycle to see if the problem has been fixed.
How To Replace Damaged Timer In Frigidaire Front Loader Washing Machine
Do the following to replace a faulty timer assembly in your Frigidaire front loader washing machine…
Step 1. Make sure to unplug your washing machine’s power cord from the power outlet before starting this repair in order to prevent any chances of electrocution.
Step 2. Push the timer knob inwards and rotate it counter-clockwise to take it out of your washing machine. Pull the indicator dial off the control panel and set it aside.
Step 3. Using your Philips screwdriver, take out the screws at the back of your washing machine holding the main top panel. Slide the panel backwards a few inches and lift it off your washing machine.
Step 4. Use your Philips screwdriver to take out the timer mounting screw on the control panel. Reach inside your washing machine and pull the timer assembly out of place.
Step 5. Disconnect the electrical connector attached to the timer assembly and set the timer aside. Take your new washing machine timer out of its packaging.
Step 6. Connect the electrical connector to the new timer assembly. Install the new timer in your washing machine and apply the screw on the control panel with your Philips screwdriver to secure it.
Step 7. Push the timer knob and indicator dial onto the timer shaft. Rotate the timer knob clockwise to secure it.
Step 8. Slide the top panel of your washing machine back on and apply the screws at the back with your Philips screwdriver to secure it.
Step 9. Plug your washing machine’s power cord back into the power supply and try running a wash cycle to see if the problem has been fixed.