If you are getting GE washing machine error codes and don’t know what to do, this guide is for you. We’ll be talking about different error codes and how to fix them. So, without further ado, let’s get right to it….
Table of Contents
GE Washing Machine Error Code E2 — Solved
The E2 error code on your GE washing machine indicates that the lid isn’t properly locked. Ensure that you firmly close your washer’s lid before starting a cycle. If the error still shows up, you’ll need to replace the lid switch. Here’s how to do this…
Step 1. Before attempting any repairs, ensure that you turn off your washing machine’s water and power supply in order to avoid water leakage and electrocution.
Step 2. Use a screwdriver to take out the screws at the back of your washing machine holding the control panel to the main top.
Step 3. Slide the control panel sideways and detach it from the main top.
Step 4. Disconnect the wires from the control board and set the board aside.
Step 5. Insert a putty knife under the main top panel of your washing machine to release the two clips holding the main front section.
Step 6. Detach the front panel from your washing machine and set it aside.
Step 7. Use your screwdriver to take out the two screws holding the top panel at the front section of your washing machine.
Step 8. Pull the top panel forward a bit and lift it up slightly.
Step 9. Reach under the top panel with a pair of pliers and release the lid switch wire retainer from the cabinet.
Step 10. Open the lid of your washing machine.
Step 11. Reach under the top panel and press the tab on the lid switch to release it.
Step 12. Push the lid switch through the opening on the top panel.
Step 13. Turn the switch sideways and push it back through the opening.
Step 14. Take the front panel off the washing machine and set it aside.
Step 15. Cut the lid switch wires as close to the lid switch as possible and set the old lid switch aside.
Step 16. Get your new lid switch out of its pack.
Step 17. Trim the wires of the new lid switch to an appropriate length and trim off about 1/4 inch of insulation from the old lid and new lid switch wires.
Step 18. Splice each wire to its corresponding counter-part and secure with wire nuts.
Step 19. Put the wire retainer back in the frame.
Step 20. Push the new lid switch through the hole in the main top panel and snap it in place.
Step 21. Push the main top panel back in place and apply the screws at the front to secure.
Step 22. Snap the main front panel of your washing machine back on.
Step 23. Connect the wires back to the control board and position the board on the main top. Apply the screws at the back to secure.
Step 24. Turn on your washing machine’s water and power supply.
Step 25. Run a wash cycle to ensure that everything is working properly.
GE Washing Machine Error Code FF — How To Fix
An FF error code on your GE washing machine indicates that the cycle has begun but no water has entered the tub. Here are the things that could prevent your washing machine from filling with water…
1.Blocked Water Inlet Filter
Here’s how to clean a clogged water inlet filter In your GE washing machine…
Step 1. Before attempting any repairs, ensure that you turn off your washing machine’s water and power supply in order to avoid water leakage and electrocution.
Step 2. Go to the back of the washing machine and disconnect the water inlet hoses.
Step 3. You will find a little mesh filter inside the water inlet port at the back of your washing machine. Pull the filter out with a pair of pliers.
Step 4. Take the mesh filter to a sink and scrub out any dirt that may have accumulated in it.
Step 5. Once the filter is clean, put it back in place inside the water inlet port at the back of your washing machine.
Step 6. Connect the water inlet hoses back to your washing machine.
Step 7. Turn on your washing machine’s water and power supply.
Step 8. Run a wash cycle to ensure that everything is working properly.
2.Faulty Water Inlet Valve
If cleaning the water inlet filter didn’t fix the issue, you’ll need to replace your washing machine’s water inlet valve. Here’s how to do this…
How To Replace A GE Top Loader Washing Machine Water Inlet Valve
To replace the water inlet valve in your GE top loader washing machine, do the following…
Step 1. Before attempting any repairs, make sure to turn off your washing machine’s water and power supply in order to avoid water leakage and electrocution.
Step 2. Go to the back of your washing machine and disconnect the water inlet hoses (get ready for some water to spill out).
Step 3. Take out the screws at the back of the control panel.
Step 4. Slide the control panel sideways and detach it from your washing machine.
Step 5. The water inlet valve will be mounted on the control panel bracket. Disconnect the solenoid wires from the valve.
Step 6. Use a pair of pliers to press the clamp on the hose connected to the water inlet valve and slide it out of place.
Step 7. Use your screwdriver to take out the mounting screws holding the water inlet valve assembly to your washing machine.
Step 8. Pull the water inlet valve assembly out of your washing machine.
Step 9. Get your new water inlet valve out of its pack.
Step 10. Install the new water inlet valve in your washing machine and apply the three mounting screws to secure it.
Step 11. Connect the hose to the new water inlet valve and secure it by sliding the retaining clamp in place.
Step 12. Connect the each solenoid wire to its appropriate terminal on the new water inlet valve.
Step 13. Put the control panel back on and secure it by applying the screws at the back.
Step 14. Connect the water inlet hoses to the ports at the back of your washing machine.
Step 15. Turn on your washing machine’s water and power supply.
Step 16. Run a wash cycle to make sure everything is working properly.
Note: Click here to learn more about washing machine water inlet valves.
How To Replace A GE Front Loader Washing Machine Water Inlet Valve
Here’s how to replace a defective water inlet valve in your your GE front loader washing machine…
Step 1. In order to avoid water leakage and electrocution, make sure to turn off your washing machine’s water and power supply before attempting any repairs.
Step 2. Go to the back of your washing machine and disconnect the water inlet hoses (be prepared for some water to leak out).
Step 3. Use a Philips screwdriver to take out the screws at the back of your washing machine holding the top panel.
Step 4. Slide the top panel back a few inches and lift it off your washing machine.
Step 5. Disconnect the solenoid wires connected to the water inlet valve inside the washing machine’s cabinet (ensure that you take note of the positioning of each wire).
Step 6. Use a pair of pliers to press the clamp holding the hose to the water inlet valve and slide it out of place.
Step 7. Disconnect the hose from the water inlet valve assembly.
Step 8. Use your Philips screwdriver to take out the two mounting screws at the back of your washing machine holding the water inlet valve.
Step 9. Pull the water inlet valve assembly out of the washing machine.
Step 10. Get your new water inlet valve assembly out of its pack.
Step 11. Install the new water inlet valve in your washing machine and secure it by applying the two Philips screws at the back of the washing machine.
Step 12. Connect the hose to the new water inlet valve assembly and slide the retaining clamp in place to secure it.
Step 13. Connect each solenoid wire to its appropriate terminal on the new water inlet valve assembly.
Step 14. Connect the water inlet hoses to their appropriate ports on the new water inlet valve assembly (ensure that the connection is properly tightened in order to avoid water leakage).
Step 15. Slide the top panel of your washing machine back on and apply the Philips screws at the back to secure it.
Step 16. Turn on your washing machine’s water and power supply.
Step 17. Try running a wash cycle to ensure that everything is working properly.
Note: Click here for more GE washing machine filling problems.
GE Washing Machine Error Code E43 — Quick Fix
An E43 error code in your GE washing machine indicates that there is an issue with the drive motor. Before going too far, unplug your washing machine for about 10 minutes and plug it back in. If the error still persists, you’ll need to replace the drive motor. Here’s how to do this…
Step 1. Before attempting any repairs, ensure that you turn off your washing machine’s water and power supply in order to avoid water leakage and electrocution.
Step 2. Insert a putty knife under the main top panel of your washing machine to release the two clips holding the front section in place.
Step 3. Detach the panel from the washing machine and set it aside.
Step 4. Take note of the positioning of the mode shifter and motor wires connected to the motor board and disconnect them.
Step 5. To release the wires from the motor frame, use a pair of pliers to squeeze the end of the motor wire retainer.
Step 6. Slide the drive belt off the drive motor pulley.
Step 7. Use a socket wrench to take out the mounting nuts at the bottom of the drive motor (you will need to tilt the drive motor forward a bit to completely take out the mounting nuts).
Step 8. Lift the drive motor off the mounting bracket.
Step 9. Get your new drive motor assembly out of its pack.
Step 10. Set the new drive motor on the mounting bracket and secure it by applying the mounting nuts (you’ll need to tilt the drive motor forward a bit to apply the rear mounting nuts).
Step 11. Loop the drive belt onto the motor shaft and drive pulley.
Step 12. Snap the wire retainer into the motor base.
Step 13. Connect each wire to its appropriate terminal on the new drive motor assembly.
Step 14. Snap the main front panel of your washing machine back in place.
Step 15. Turn on your washing machine’s water and power supply.
Step 16. Run a wash cycle to ensure that everything is working properly.
Check out these other articles…
LG Washing Machine Lights [Issues & Solutions]
LG Washing Machine Vibrating Too Much [How To Fix]
LG Washing Machine Beeps [Issues & Solutions]
GE Washing Machine Filling [Problems & Solutions]
GE Washing Machine Light [Problems Solved]
GE Washing Machine Error Code H20 — Solved
An H20 error code on your GE washing machine indicates that the washer isn’t filling as a result of a turned off water supply. Ensure that your hot and cold water supply valves are fully opened. If your washer still doesn’t fill with water, here are things to check..
1.Water Inlet Filter Is Clogged
Here’s how to clean a clogged water inlet filter In your GE washing machine…
Step 1. In order to avoid water leakage and electrocution, make sure to turn off your washing machine’s water and power supply before attempting any repairs.
Step 2. Go to the back of the washing machine and disconnect the water inlet hoses.
Step 3. You’ll find a little mesh filter inside each of the two water inlet ports at the back of your washing machine. Pull the filters out with a pair of pliers.
Step 4. Take the filters to a sink and use a soft brush to clean out any dirt that may have accumulated in them.
Step 5. Once you’ve cleaned the filters properly, put them back in place inside the water inlet ports at the back of your washing machine.
Step 6. Reconnect the water inlet hoses to the back of your washing machine.
Step 7. Turn on your washing machine’s water and power supply.
Step 8. Run a wash cycle to ensure that everything is working properly.
2.Water Inlet Valve Is Defective
If the issue wasn’t fixed after cleaning the water inlet filter, you’ll need to replace your washing machine’s water inlet valve. Here’s how to do this…
How To Replace A GE Front Loader Washing Machine Water Inlet Valve
Do the following to replace a defective GE front loader washing machine water inlet valve…
Step 1. Make sure to turn off your washing machine’s water and power supply before attempting any repairs in order to avoid water leakage and electrocution.
Step 2. Go to the back of your washing machine and disconnect the water inlet hoses (keep a rag handy in case of water leakage).
Step 3. Use a Philips screwdriver to take out the screws at the back of your washing machine holding the top panel.
Step 4. Slide the top panel back a few inches and lift it off your washing machine.
Step 5. Disconnect the solenoid wires connected to the water inlet valve inside the washing machine’s cabinet (make sure to take note of the positioning of each wire).
Step 6. Use a pair of pliers to press the clamp holding the hose to the water inlet valve and slide the clamp out of place.
Step 7. Disconnect the hose from the water inlet valve assembly.
Step 8. Take out the two mounting screws at the back of your washing machine holding the water inlet valve with a Philips screwdriver.
Step 9. Pull the water inlet valve assembly out of the washing machine.
Step 10. Get your new water inlet valve assembly out of its pack.
Step 11. Install the new water inlet valve in your washing machine and secure it by applying the two Philips screws at the back of your washing machine.
Step 12. Connect the hose to the new water inlet valve assembly and slide the retaining clamp in place to secure it.
Step 13. Connect each solenoid wire to its appropriate terminal on the new water inlet valve assembly.
Step 14. Connect the water inlet hoses to their appropriate ports on the new water inlet valve assembly (ensure that the connection is properly tightened in order to avoid water leakage).
Step 15. Slide the top panel of your washing machine back on and apply the Philips screws at the back to secure it.
Step 16. Turn on your washing machine’s water and power supply.
Step 17. To ensure that everything works properly, try running a wash cycle.
How To Replace A GE Top Loader Washing Machine Water Inlet Valve
Here’s how to replace a defective water inlet valve in your GE top loader washing machine…
Step 1. Always remember to turn off your washing machine’s power and water supply before attempting any repairs in order to avoid electrocution and water leakage.
Step 2. Go to the back of your washing machine and disconnect the water inlet hoses (keep a rag nearby in case some water leaks out).
Step 3. Take out the screws at the back of the control panel.
Step 4. Slide the control panel sideways and detach it from your washing machine.
Step 5. The water inlet valve will be mounted on the control panel bracket. Disconnect the solenoid wires from the valve.
Step 6. Use a pair of pliers to press the clamp on the hose connected to the water inlet valve and slide it out of place.
Step 7. Use your screwdriver to take out the mounting screws holding the water inlet valve assembly to your washing machine.
Step 8. Pull the water inlet valve assembly out of your washing machine.
Step 9. Get your new water inlet valve out of its pack.
Step 10. Install the new water inlet valve in your washing machine and apply the three mounting screws to secure it.
Step 11. Connect the hose to the new water inlet valve and secure it by sliding the retaining clamp in place.
Step 12. Connect the each solenoid wire to its appropriate terminal on the new water inlet valve.
Step 13. Put the control panel back on and secure it by applying the screws at the back.
Step 14. Connect the water inlet hoses to the ports at the back of your washing machine.
Step 15. Turn on your washing machine’s water and power supply.
Step 16. Run a wash cycle to ensure everything is working properly.
How Do You Clear An Error Code On A GE Washing Machine?
The quickest way to clear an error code on your GE washing machine is to turn off the power supply for about 10 minutes and then plug it back in. If the error code still shows up after this, it indicates a more serious problem.