LG washing machine error codes can be a bit of a mystery to quite a few users. If you are one of these people, you’ve come to the right place. In this detailed guide, we’ll be giving you the meanings of various error codes and instructions on how to deal with them.
So, with that being said, let’s get right to it…
Table of Contents
LG Washing Machine Error Code PE — How To Fix
The LG washing machine error code PE indicates that there is an issue with the washer’s water level sensor (also known as water pressure switch).
Before attempting any complex repairs, you need to ensure that its not just a temporary glitch. You can test this by unplugging your washing machine for about 10 minutes and then plugging it back in.
If you still get the error code, you will need to replace the water pressure switch. Here’s how to do this…
Step 1. Turn off your washing machine’s water and power supply.
Step 2. Using a Philips screwdriver, remove the two screws at the back of the washer holding the top panel.
Step 3. Slide the panel back a few inches and lift it off the washing machine.
Step 4. The water pressure switch will be found mounted on the washer’s cabinet wall near the water inlet valve.
Step 5. Detach the wire harness connected to the water pressure switch.
Step 6. Using a Philips screwdriver, remove the mounting screw holding the water pressure switch to the washing machine.
Step 7. Pull the water pressure switch out of the washing machine.
Step 8. Detach the rubber tube connected to the water pressure switch.
Step 9. Take your new water pressure switch out of its pack.
Step 10. Attach the rubber tube to the new water pressure switch.
Step 11. Mount the new pressure switch on the washer’s cabinet frame.
Step 12. Apply the mounting screw to secure the water pressure switch.
Step 13. Attach the wire harness to the new water pressure switch.
Step 14. Put the washer’s top panel back in place.
Step 15. Reapply the two screws at the back to secure the top panel.
Step 16. Turn on your washing machine’s water and power supply.
Step 17. Run a wash cycle to see if the issue has been resolved.
Note: Please keep in mind that the process of replacing this part will vary depending on the type of washing machine you have. If you couldn’t follow the procedure above on your washer, it is strongly advised that you contact a washer repair service to help you.
LG Washing Machine Error Code DE — Solution
A DE error code on your LG washing machine indicates that the door isn’t locked. Most times this can be fixed simply by turning the washing machine off, firmly closing the door/lid, and starting it up again.
However, if this doesn’t work, you will need to replace the door lock assembly. Here’s how to do this…
Step 1. Turn off your washing machine’s water and power supply to avoid electrocution and water spills.
Step 2. Open the door of your washing machine.
Step 3. Around the edge of the gray door seal, you will find a metal band. Wedge a flat-blade screw driver under the band and work your way around until you can take the whole band out (be careful not to damage the seal).
Step 4. With the band removed, carefully peel the seal towards your left (away from the door lock).
Step 5. Using a Philips screwdriver, undo the two screws holding the door lock assembly.
Step 6. With the screws removed, push the door lock inwards (make sure to put your hand at the other side to hold the lock).
Step 7. Disconnect the wire harness connected to the door lock assembly.
Step 8. Take your new door lock out if its pack.
Step 9. Attach the wire harness to the new door lock assembly.
Step 10. Pop the new door lock in the same position as the one you removed (make sure to support the lock with your hand).
Step 11. Reapply the two Philips screws to secure the door lock.
Step 12. Push the gray door seal back in place and ensure that it is properly aligned.
Step 13. Fit the metal band back around the door seal (you may need the flat-blade screwdriver to do this).
Step 14. Close your washer’s door.
Step 15. Turn on your washing machine’s water and power supply.
Step 16. Run a wash cycle to see if the issue has been fixed.
Note: When buying parts ensure that you check your washing machine’s specific model.
How To Reset LG Washing Machine Error Code AE
The AE error code often pops up when the room the washer wash installed is very humid. You can clear this error code by resetting the washing machine.
To do this, all you need to do is turn off your washing machine’s power supply for about 20 minutes and then plug it back in. This will clear any system glitches. You should also consider removing your washing machine from the humid environment.
LG Washing Machine Error Code CL — How To Fix
The CL code on an LG washing machine isn’t actually an error code. It simply indicates that the washer’s Child Lock feature is activated. To clear the code, you’ll need to turn Child Lock off.
The button you need to press to turn Child Lock off will vary depending on the model of your washer. For some washer’s you simply need to press and hold the Rinse+Spin button for 3 seconds.
For other washer’s you’ll have to press the Soil button for 3 seconds. You can also try holding the Water Level and Spin buttons simultaneously for 3 seconds. If none of these methods worked for you, try looking for a button on your washer’s control panel with “Child Lock” written on it. This is the button you’ll need to press.
Check out these other articles…
LG Washing Machine Overflowing [How To Fix]
How To Unlock An LG Washing Machine [A Guide]
LG Washing Machine Draining [How To/Issues & Solutions]
LG Washing Machine Door [How To/Issues & Solutions]
LG Washing Machine Smells [How To Fix]
LG Washing Machine Error Code LE — Solution
An LE error code on your washer’s display, it means that the machine’s motor is locked. This is often caused by overloading the washer’s drum with clothes.
Most times, this issue can be fixed by turning off your washer’s power supply, reducing the quantity of clothes in the drum, and then turning the machine back on.
If this doesn’t resolve the issue, you will need to replace your washing machine’s drive motor. Here’s how to do this…
How To Replace An LG Washing Machine Drive Motor — Front Loaders
Do the following to replace the drive motor on your LG front loader washing machine…
Step 1. Turn off your washing machine’s water and power supply to avoid electrocution and water leakage.
Step 2. Go to the back of your washing machine.
Step 3. Using a Philips screwdriver, remove the screws holding the washer’s back panel.
Step 4. With the screws removed, push the panel up and pull it out of the washing machine.
Step 5. Get socket wrench with a 17mm cap.
Step 6. The drive motor will be found directly at the back of the washer under the panel. Use the wrench to remove the 17mm bolt in the middle (you’ll need to hold the motor still with your hand to be able to do this easily).
Step 7. With the bolt removed, pull the rotor covering the drive motor out of the washer.
Step 8. Switch the cap on your socket wrench to a 10mm one.
Step 9. Using the wrench, remove the six bolts holding the drive motor.
Step 10. While supporting the drive motor, detach the two electrical connectors attached to it (use a flat-blade screwdriver if needed).
Step 11. Pull the drive motor out of your washing machine.
Step 12. Take your new drive motor out of its pack.
Step 13. Line the new drive motor on the rear end of the washer’s tub.
Step 14. Secure the new drive motor to the tub by applying the six 10mm bolts.
Step 15. Connect each of the electrical connectors to its appropriate terminal on the drive motor.
Step 16. Place the rotor assembly over the drive motor.
Step 17. Switch the cap on your wrench to the 17mm one.
Step 18. Using the wrench, reapply the bolt that goes at the center of the rotor assembly.
Step 19. Put the washer’s rear panel back in place.
Step 20. Reapply the screws on the panel to secure it.
Step 21. Turn on your washing machine’s water and power supply.
Step 22. Run a wash cycle to see if the issue has been resolved.
How To Replace An LG Washing Machine Drive Motor — Top Loaders
Here’s how to replace the drive motor on your LG top loader washing machine…
Step 1. Turn off your washing machine’s water and power supply to avoid electrocution and water spills.
Step 2. Disconnect your water inlet hose from the back of the washing machine.
Step 3. Tape the lid of your washing machine closed.
Step 4. Carefully tilt the washer downwards and lay it on the ground so you can access the bottom of the machine.
Step 5. The drive motor will be found directly under the machine. To access the drive motor, you’ll first need to remove the rotor assembly covering it. Get an adjustable wrench.
Step 6. Using the wrench, remove the bolt at the center of the rotor assembly (you may need to hit the wrench with a hammer as you turn, because the bolt will be a bit tough to remove).
Step 7. Once you’ve gotten the bolt out, pull the rotor assembly off the washing machine.
Step 8. Use a 10mm socket wrench to remove the six bolts holding the drive motor to the washer’s tub.
Step 9. Disconnect the two electrical connectors attached to the drive motor.
Step 10. Pull the drive motor out of your washing machine.
Step 11. Get your new drive motor out of its pack.
Step 12. Line the new drive motor up on the rear end of the washer’s tub and reapply the six bolts to secure it.
Step 13. Connect each of the two electrical connectors to its appropriate port on the new drive motor.
Step 14. Place the rotor assembly over the drive motor.
Step 15. Using your adjustable wrench, apply the bolt in the middle of the rotor.
Step 16. Lift the washing machine upright.
Step 17. Remove the tape on your washing machine’s lid.
Step 18. Connect your water supply hose to the back of your washing machine.
Step 19. Turn on your washing machine’s water and power supply.
Step 20. Run a wash cycle to see if the issue has been resolved.
LG Washing Machine IE Error Code — How To Fix
An IE error code on your LG washer indicates that the machine is not filling with water. Sometimes this is a result of not fully opening your washer’s water supply. It may caused by a frozen water line.
However, if neither is the case, the fault is from the water inlet valve. This part is responsible for allowing water into the machine. If it is damaged, your washing machine won’t get any water.
Here’s how to replace a water inlet valve on your LG washing machine…
How To Replace A Water Inlet Valve On An LG Washing Machine — Front Loaders
Do the following to replace a defective water inlet valve on your LG front load washing machine…
Step 1. Turn off your washing machine’s water and power supply to avoid electrocution and water leakage.
Step 2. Disconnect the water inlet hose from the back of your washing machine.
Step 3. Using a Philips screwdriver, remove the two screws at the back of the washing machine holding the top panel.
Step 4. With the screws removed, slide the panel back a few inches and lift it off the washer.
Step 5. The water inlet valve will be found inside the washer at the other side of the water inlet port. Disconnect the electrical connectors attached to the water inlet valve.
Step 6. You’ll see some black hoses connected to the water inlet valve (take note of the positioning of each hose).
Step 7. Using a pair of pliers, press the clamp on each hose and slide it out of place.
Step 8. Disconnect the hoses from the water inlet valve.
Step 9. The water inlet valve is held to the washing machine by two screws found beside the water inlet port. Remove the screws with a screwdriver.
Step 10. With the screws taken out, pull the water inlet valve out of the washing machine.
Step 11. Take your new water inlet valve out of its pack.
Step 12. Pop the new water inlet valve in the same position as the one you removed.
Step 13. Secure the new valve to the washer by applying the two screws.
Step 14. Connect each black hose to its appropriate port on the water inlet valve.
Step 15. Slide the metal clamps in place to secure the hoses to the water inlet valve.
Step 16. Connect each electrical connector to its appropriate terminal on the water inlet valve.
Step 17. Put the washer’s top panel back in place.
Step 18. Secure the panel by reapplying the two screws.
Step 19. Connect the water inlet hose to the back of your washing machine.
Step 20. Turn on your washing machine’s water and power supply.
Step 21. Run a wash cycle to see if the issue has been resolved.
How To Replace A Water Inlet Valve On An LG Washing Machine — Top Loaders
Do the following to replace the water inlet valve on your LG top loader washing machine…
Step 1. Turn off your washing machine’s water and power supply to avoid electrocution and water spills.
Step 2. Go to the back of your washing machine.
Step 3. The back panel of the control board is held by five screws (three at the top and two at the bottom). Remove the screws with a Philips screwdriver.
Step 4. With the screws removed, detach the control housing and lay it down on the washer’s lid.
Step 5. Disconnect the water inlet hose from the water inlet valve (some water may spill out).
Step 6. Disconnect the solenoid wires connected to the water inlet valve (take note of the positioning of each one).
Step 7. Using a pair of pliers, press the metal clamp on each of the black hoses connected to the valve and slide it out of place.
Step 8. Disconnect each hose from the water inlet valve.
Step 9. Remove the two screws holding the water inlet valve to the washing machine.
Step 10. Pull the water inlet valve out of the washing machine.
Step 11. Take your new water inlet valve out of its pack.
Step 12. Pop the new valve in the same position as the one you removed.
Step 13. Connect each black hose to its appropriate port on the new valve.
Step 14. Slide the metal clamps in place to secure the hoses.
Step 15. Connect each solenoid wire to its appropriate terminal on the valve.
Step 16. Secure the valve to the washer by applying the two Philips screws.
Step 17. Lift the washer’s control panel and put it back in place.
Step 18. Put the rear panel of the control board back in and secure it by reapplying the five screws.
Step 19. Connect your water inlet hose to the back of the washing machine.
Step 20. Turn on your washing machine’s water and power supply.
Step 21. Run a wash cycle to see if the issue has been resolved.
What Does The DE Error Code Mean On An LG Washing Machine?
A DE Error code on an LG washing machine indicates that the washer was unable to lock the door. Most times, this occurs when you don’t properly shut the washer’s door. If this isn’t the case, the fault may be from the door lock assembly.
LG Washing Machine OE Error Code — How To Fix
An OE error code on an LG washer indicates that water isn’t draining out of the machine. There are different things that could cause this issue; here are some of them…
1. Improper Drain Hose Installation
If your drain hose isn’t installed properly, the washing machine won’t be able to drain water normally.
You need to go to the back of the machine and ensure that the drain hose hasn’t been inserted more than eight inches into your home drain. It also shouldn’t be inserted less than six inches.
You should also ensure that the drain hose isn’t bent or kinked, as this can prevent your washing machine from draining water efficiently.
2. Clogged Drain Pump Filter (Front Loaders Only)
Here’s how to clear your LG washing machine’s drain pump filter…
Step 1. Turn off your washing machine’s water and power supply to avoid electrocution and water leakage.
Step 2. Place some rags or old towels on the ground in front of your washing machine.
Step 3. Flip open the little panel in front of your washing machine at the bottom.
Step 4. Under the panel, you will find a hose with a cap; pull the hose out.
Step 5. Place a container underneath the hose.
Step 6. Pull the hose’s cap off and let any water stuck in the washer’s drum drain out.
Step 7. Once all the water has drained out, put the hose’s cap back on and push the hose back in place.
Step 8. Turn the knob beside the drain hose counterclockwise to pull it out (this is known as the drain pump filter) .
Step 9. Take the filter to a sink and remove any lint or debris that may be clogging it.
Step 10. Rinse the filter thoroughly and put it back in place (turn it clockwise to secure).
Step 11. Flip the panel back in place.
Step 12. Turn on your washing machine’s water and power supply.
Step 13. Run a wash cycle to see if the issue has been resolved.
3. Defective Drain Pump
Here’s how to replace a defective drain pump on your LG washing machine…
Step 1. Buy your new drain pump: to ensure that the part you buy is compatible with your machine, make sure to check your washer’s model number.
Step 2. Turn off your washing machine’s water and power supply to avoid electrocution and water leakage.
Step 3. Using a Philips screwdriver, remove the two screws at the back of the washer securing the machine’s top panel.
Step 4. Slide the panel back an inch or so and lift it off the washing machine.
Step 5. Pull out your washing machine’s detergent drawer (press the blue tab in it to pull it out of the washer completely).
Step 6. When you remove the detergent drawer, you will see two Philips screws in the soap drawer compartment on the washer. These screws hold the user control panel. Take the screws out and set them aside.
Step 7. Once the screws are taken out, you’ll need to go to the other side of the control panel inside the machine. You will find two clips. Use something like a screwdriver to release the clips.
Step 8. Pull the control panel out of the washer and rest it on top of the cabinet frame.
Step 9. Using a flat-blade screwdriver (or your hand), open the filter covering panel in front of your washer at the bottom.
Step 10. Pull the emergency drain hose out a bit (you will see a screw behind the hose).
Step 11. Use your Philips screwdriver to take the screw out.
Step 12. Pull the whole bottom panel out of the washing machine and set it aside.
Step 13. Open the door of your washing machine.
Step 14. There will be a metal band around the gray door gasket. Wedge a flat-blade screwdriver under the wire and work your way around until you can take the whole band out.
Step 15. Peel the edges of the door seal from around the door opening.
Step 16. Use a screwdriver to undo the two screws at the right side of the drum opening (this holds the door lock assembly).
Step 17. There will be two screws at the top of the washing machine’s front panel (one at each corner). take the screws out.
Step 18. Go to the bottom of the washing machine’s front panel and undo the three screws there (two at the left and one a bit towards the right).
Step 19. With all five screws removed, lift the front panel up and pull it out of the washing machine.
Step 20. Using a Philips screwdriver, remove the three screws around the drain pump filter cover.
Step 21. Take a picture of the positioning of all the pipes and cables to help you with the reassembly process.
Step 22. Using a pair of pliers, press the clips on each the tubes connected to the drain pump.
Step 23. Detach the electrical connector connected to the drain pump.
Step 24. Pull the drain pump out of your washing machine.
Step 25. Take your new drain pump out of its pack.
Step 26. Pop the new drain pump in the same position as the one you removed.
Step 27. Attach the electrical connector to the new drain pump.
Step 28. Connect each hose to the drain pump and secure the hoses with the clamps (use the images on your phone as a reference if necessary).
Step 29. Secure the new drain pump by applying the three screws around the filter cover.
Step 30. Pass the emergency drain hose of your new drain pump out through the provided opening.
Step 31. Put the washing machine’s front panel back on and secure it with the five screws.
Step 32. Put the bottom panel back in place and secure it with the screw.
Step 33. Fit the washer’s door seal back in place around the door opening.
Step 34. Fit the retaining band around the door seal (you may need the help of a screwdriver).
Step 35. Lift the user control panel from the top of the washer and pop it back in place.
Step 36. Reapply the two screws to secure the panel.
Step 37. Put the detergent drawer back in place.
Step 38. Put the washing machine’s top panel back on and secure it at the back with the two screws.
Step 39. Turn on your washing machine’s water and power supply.
Step 40. Try running a wash cycle to see if the issue has been resolved.
Note: The process above is for front load washers only. If you have another type of washer, please contact a washer repair service.
This is a complex repair. If you are not confident in your repair skills, please do not attempt this procedure. You could end up damaging another component in your washing machine.
LG Washing Machine Error Code DE — How To Fix
A DE error code on your LG washing machine indicates that the washer was unable to lock the door.
Most times, this can be fixed simply by turning off the washer’s power supply, opening the door, and firmly shutting it. If the error code is still there after this, you’ll need to replace your washing machine’s door lock.
Here’s how to replace the door lock on your LG washing machine…
Step 1. Turn off your washing machine’s water and power supply to avoid electrocution and water leakage.
Step 2. Open the door of your washing machine.
Step 3. Around the gray door seal in the door opening, there is a metal retaining band. To remove the band, you’ll need a flat-head screwdriver.
Step 4. Wedge the screwdriver under the metal band and work your way around until you can take the whole band out.
Step 5. Peel the gray door seal towards the left a bit (away from the door lock).
Step 6. Using a Philips screwdriver, undo the two screws securing the door lock assembly.
Step 7. Put your hand inside the machine and support the other side of the door lock as you push it out of the washer.
Step 8. Detach the electrical connector connected to the door lock assembly.
Step 9. Take your new door lock assembly out of its pack.
Step 10. Plug the electrical connector to the new door lock assembly.
Step 11. Pop the new door lock assembly in the same place as the one you removed.
Step 12. Secure the door lock assembly by applying the two screws.
Step 13. Push the gray door seal back in place and fit the retaining band around it (you may need a screwdriver to do this).
Step 14. Close the door of your washing machine.
Step 15. Turn on your washing machine’s water and power supply.
Step 16. Run a wash cycle to see if the issue has been resolved.
LG Washing Machine Error Code SUD — Solved
An SUD error code on your LG washing machine indicates that there is excessive foaming in the drum. Most times this issue occurs when you put too much detergent in your washer.
When too many suds are produced, the washing machine will stop running and display the SUD error code to prevent water from leaking. To avoid this issue, never fill the detergent drawer past the MAX indicator.
It is also that you only use HE (High Efficiency) detergent when washing. This type of detergent wash made specifically for washing machines. It doesn’t produce as much suds as normal detergent.
LG Washing Machine Error Code TCL — Quick Fix
The TCL code on your LG washing machine isn’t necessarily an error. This code simply indicates that it is time to run a Tub Clean cycle.
It’s completely normal for your LG washing machine to show this code every now and then. If you want to clear this code, you’ll need to run a Tub Clean cycle.
To run a Tub Clean cycle on your LG washing machine, do the following…
Step 1. Remove all clothes from your washing machine.
Step 2. Turn on your washing machine’s water and power supply.
Step 3. Using the control dial, select the Tub Clean option (depending on the model of your washer, there will be a Tub Clean button on the control panel).
Step 4. Press the Start button to begin the Tub Clean cycle.
Note: To keep your washing machine clean, it is advised that you run a Tub Clean cycle every fifty washes or so.
LG Washing Machine Error Code UE — How To Fix
An LG washing machine UE error code indicates that the load in the washer is unbalanced. Here’s how to fix this issue…
Step 1. Ensure that you only put a moderate quantity of clothes in your washing machine. The recommended quantity of clothes to put per wash will vary depending on the size of your machine. Please consult your manual to learn more.
Step 2. Ensure that the washing machine sits on an even surface: If your washing machine sits tilted at an angle the weight of the clothes will be resting only one side of the drum. This will make it difficult for the washer to spin. If necessary, adjust the washer’s legs to level them.
Step 3. Distribute the clothes evenly in the drum. This will help balance the load and make it easier for the washing machine to spin.
Note: This applies to both front loaders and top loaders.
How Do I Fix PF Error Code On My LG Washing Machine?
A PF error code on your LG washing machine simply indicates that there has been a power failure. This tends to occur after a power outage. To fix this issue, unplug your washer from the power supply for about ten minutes and then plug it back in. This should clear the error code.
LG Washing Machine Error Code TE — Easy Fix
A TE Error code on an LG washing machine indicates that the heating element is defective. As a result, the washer won’t be able to heat water properly.
To clear this error code, you’ll need to replace your washing machine’s heater assembly. Here’s how to do this…
Step 1. Turn off your washing machine’s water and power supply to avoid electrocution and water leakage.
Step 2. Using a Philips screwdriver, remove the two screws securing the top panel of your washing machine.
Step 3. With the screws removed, slide the panel back a few inches and lift it off the washing machine.
Step 4. Pull out your washer’s detergent drawer and press the blue tab in the middle to take it out completely.
Step 5. When you remove the drawer, you will see two screws beside the soap dispenser opening (one on each side). Use a Philips screw driver to take the screws out.
Step 6. Use your screwdriver to take out the screw at the back of the user control panel (right side).
Step 7. With the screws removed, pull the user control panel up and towards you while disconnecting the tabs on it.
Step 8. Once you’ve pulled the panel out, lay it down on top of your washing machine (wires will still be connected to the user control panel).
Step 9. Flip open the little panel at the bottom left of your washing machine.
Step 10. Pull out the emergency drain hose and take out the screw near it.
Step 11. Take out the housing of the filter cover.
Step 12. When you take the housing out, you’ll see another screw beneath the emergency drain hose and the filter cover. Take the screw out.
Step 13. Open the door of your washing machine.
Step 14. Around the gray door seal, there is a metal retaining band. You will need a flat-blade screwdriver to take it out.
Step 15. Wedge the screwdriver under the band and work your way around until you can take the whole band off.
Step 16. Peel the door seal away from the opening and tuck it into the washer’s drum.
Step 17. Reach in behind the door lock (right side of your washer’s door) and disconnect the wire harness connected to it.
Step 18. Close the door of your washing machine.
Step 19. Using your Philips screwdriver, remove the five screws at the top of the washer’s front panel.
Step 20. Lift the washer’s front panel off its bottom hinge and set it aside in a safe place.
Step 21. Place a container underneath the emergency drain hose.
Step 22. Pull the hose’s cap off and drain out any water that may still be in the washing machine’s drum.
Step 23. Once all the water has drained out, put the hose’s cap back on.
Step 24. The heater assembly will be mounted at the bottom of the washer’s drum. Using a 10mm socket wrench, remove the bolt at the center of the heater assembly out the ground wire.
Step 25. Detach the electrical connectors on each side of the heater assembly (use a flat-blade screwdriver if needed).
Step 26. Using the 10mm socket wrench, remove the bolt at the center of the heater assembly.
Step 27. With both hands, carefully pull out the heater assembly from underneath the washer’s tub.
Step 28. Take your new heater assembly out of its pack.
Step 29. Insert the new heater assembly into place at the bottom of the washer’s tub.
Step 30. Using your 10mm socket wrench, tighten the bolt at the center of the heater assembly.
Step 31. Connect each of the two wire harnesses to it’s appropriate terminal on the heater assembly.
Step 32. Align the front panel of the washing machine and secure it by applying the five screws at the top.
Step 33. Once the screws are secured, open the door of your washing machine and reconnect the door lock’s wire harness.
Step 34. Line the door seal around the opening and fit the retaining band around it (you may need the help of a flat-blade screwdriver to do this).
Step 35. Close the door of your washing machine.
Step 36. Go down to the drain hose compartment and reapply the screw.
Step 37. Push the drain pump housing back in place and secure it with the screw.
Step 38. Close the cover of the drain pump housing.
Step 39. Lift the user control panel from the top of the washer and pus it back in place.
Step 40. Secure the panel by reapplying the screw at the back of the panel and the two screws beside the detergent drawer housing.
Step 41. Slide the detergent drawer back in place.
Step 42. Put the washer’s top panel back in place and secure it by applying the two screws at the back of the machine.
Step 43. Turn on your washing machine’s water and power supply.
Step 44. Run a wash cycle to see if the issue has been resolved.
Note: Please keep in mind that this is a complex repair. If you aren’t confident in your washer repair skills, please consider contacting a washer repair service.
Also note that the method above is only for front loaders; you will not be able to follow this procedure on a top load washer.
LG Washing Machine Error Code UB — Solution
A UE error code on your LG washing machine indicates that the load in the washer isn’t balanced. Most times this occurs when the load in the washer is too big or too small.
To avoid this issue, always put a moderate quantity of clothes in the drum. The recommended quantity of clothes per wash will vary a lot depending on the size of your washing machine. Consult your manual to learn the right amount of clothes to put.
Another thing that can cause an unbalanced load is if your washer sits tilted at an angle. If this happens, the weight of the clothes will rest on only one side of the washer’s drum. This makes it difficult for the washer to spin.
Ensure that your washing machine sits on a firm, even surface. If needed, adjust the legs of the machine so that they are all level.
Tip: Distribute the weight of the clothes evenly in the drum to help balance the load.
LG Washing Machine Error Code 1E — How To Fix
A 1E error code on an LG washing machine indicates that the washer isn’t filling with water. This issue can often be caused by a frozen water line or a partially opened water supply line.
However, if neither of these are the cause, the fault lies with the water inlet valve. You’ll need to replace water inlet valve to fix this issue. Here’s how to do this…
How To Replace LG Washing Machine Water Inlet Valve — Top Loaders
Do the following to replace the water inlet valve on your LG top loader washing machine…
Step 1. Turn off your washing machine’s water and power supply to avoid electrocution or water leakage.
Step 2. Using a Philips screwdriver, remove the five screws at the back of the washing machine’s user control panel (three at the top and two at the bottom).
Step 3. With the screws removed, take out the back panel of the user control board.
Step 4. Disconnect the control panel housing and lay it on top of the washing machine.
Step 5. Detach the water inlet hose/hoses from the water inlet valve (some water may spill out).
Step 6. Disconnect the solenoid wires connected to the water inlet valve (take note of the positioning on each wire).
Step 7. Using a pair of pliers, press the metal clamp on each hose connected to the valve and slide it out of place.
Step 8. Disconnect each hose from the water inlet valve.
Step 9. Take out the three screws holding the water inlet valve to the washing machine.
Step 10. Take the water inlet valve out of the washing machine.
Step 11. Take your new water inlet valve out of its pack.
Step 12. Line the new water inlet valve up in the same place as the one you removed and secure the valve with the three screws.
Step 13. Connect each black hose to its appropriate port on the new water inlet valve.
Step 14. While pressing with the pliers, slide each clamp in place to secure the hoses to the new water inlet valve.
Step 15. Attach each solenoid wire to its appropriate terminal on the new water inlet valve.
Step 16. Connect your water inlet hose/hoses to the new water inlet valve.
Step 17. Put the control housing back in place.
Step 18. Put the rear panel of the control housing back on and secure it with the five Philips screws.
Step 19. Turn on your washing machine’s water and power supply.
Step 20. Run a wash cycle to see if the issue has been resolved.
How To Replace An LG Washing Machine Water Inlet Valve — Front Loaders
Do the following to replace the water inlet valve on your LG front loader washing machine…
Step 1. Turn on your washing machine’s water and power supply to avoid water leakage or electrocution.
Step 2. Disconnect the water inlet hose/hoses from the back of the washing machine.
Step 3. Using a Philips screwdriver, remove the two screws at the back of the washing machine securing the top panel.
Step 4. Slide the panel back a few inches and lift it off the washing machine.
Step 5. The water inlet valve will be found inside the washer on the other side of the water inlet port. Disconnect each solenoid wire connected to the water inlet valve (take note of the positioning of each wire).
Step 6. Using a pair of pliers, press the clamp on each hose connected to the water inlet valve and slide them out of place.
Step 7. Disconnect each hose from the water inlet valve (take note of the positioning of each hose).
Step 8. The water inlet valve is held to the washer by two screws at the back of the washer next to the water inlet port. Take the screws out with a Philips screwdriver.
Step 9. Pull the water inlet valve out of the washing machine.
Step 10. Take your new water inlet valve out of its pack.
Step 11. Pop the new water inlet valve into the same position as the one you removed.
Step 12. Secure the water inlet valve to the washer by applying the two screws.
Step 13. Connect each hose to its appropriate port on the new water inlet valve.
Step 14. While pressing with pliers, slide the clamps in place to secure the hoses to the new water inlet valve.
Step 15. Connect each solenoid wire to its appropriate terminal on the new water inlet valve.
Step 16. Ensure that all connections are secure to avoid water leakage.
Step 17. Slide the washing machine’s top panel back in place and secure it with the two Philips screws.
Step 18. Connect the water inlet hose/hoses to the back of your washing machine.
Step 19. Turn on your washing machine’s water and power supply.
Step 20. Run a wash cycle to see if the issue has been resolved.
Note: If you had trouble following the procedure above, it is advised that you contact a washer repair service to help you replace this part.
LG Washing Machine Error Code DL — Solved
A DL error code on your LG top loader washing machine indicates that your washer’s door isn’t properly locked.
Most of the time, this issue can be fixed by turning off your washer’s power supply, removing the clothes, and then loading them back in after about 10 minutes.
However, if this doesn’t fix the issue, you’ll need to replace your washing machine’s door lock. Here’s how to do this…
Step 1. Turn off your washing machine’s water and power supply to avoid electrocution or water leakage.
Step 2. Using a Philips screwdriver, remove the five screws holding the back panel of the washer’s control board (three at the top and two at the bottom).
Step 3. With the screws removed, take the back panel off.
Step 4. Detach the control housing and lay it on top of the washer’s lid.
Step 5. Use your screwdriver to take out the screws holding the control assembly cover and pry the cover open.
Step 6. Set the cover aside.
Step 7. Detach the lid lick wire connector from the washer’s main control board.
Step 8. Lift the control housing and put it back in place.
Step 9. Open the lid of your washing machine.
Step 10. Using a putty knife, release the locking clips holding the main top of the washing machine.
Step 11. Lift up the main top of the washing machine and support it.
Step 12. Use your screwdriver to remove the mounting screws holding the lid lock.
Step 13. Pull the lid lock out of place.
Step 14. Release the wire sleeve connected to the lid lock from the hose and dispenser.
Step 15. Pull the remaining part of the wire out of the washing machine.
Step 16. Take your new lid lock assembly out of its pack.
Step 17. Transfer the wire retainer from the old lock to the new one.
Step 18. Position the new lid lock under the washer’s top cover.
Step 19. Secure the lid lock and the wire retainer with the mounting screws.
Step 20. Secure the new wire sleeve the same way the old one was.
Step 21. Push the electrical connector attached to the wire sleeve through the hole at the top of the washer.
Step 22. Remove the support holding the main top of the washer.
Step 23. Lower the main top of the washing machine and snap it in place.
Step 24. Close the lid of your washing machine.
Step 25. Detach the control housing once more and lay it on the washer’s lid.
Step 26. Connect the new lid lock electrical connector to your washer’s main control board.
Step 27. Cover the main control board with the panel and secure it with the mounting screws.
Step 28. Put the control housing back in place.
Step 29. Put the back panel of the control housing in place and secure it with the five screws.
Step 30. Turn on your washing machine’s water and power supply.
Step 31. Run a wash cycle to see if the issue has been fixed.
Note: Please keep in mind that this repair can get complex. If you aren’t confident in your repair skills, we strongly advise against attempting this fix. Your best option is to call a washer repair service to help you.
How To Reset LG Washing Machine Error Code
Resetting an LG washing machine error code is very simple. All you need to do is unplug your washing machine for about ten minutes and then plug it back in. This will clear any system glitches that may have caused the error code to pop up.
Click here for more error codes.
LG Washing Machine Error Code UC — Solution
A UC error code on your LG washing machine indicates that there has been an increase or decrease in the voltage. You can fix this issue by unplugging your washing machine for twenty minutes and plugging it back in.
You should also consider getting an electrician to take a look at your power supply to ensure that there isn’t a more serious issue.
LG Washing Machine Error Code FE — Solved
The LG washing machine error code FE indicates that the washing machine is overfilling with water. This issue can be caused by two things; the water inlet valve and the water level sensor.
These two components control the quantity of water that enters the washer. If either part is defective, your machine will overflow. Here’s how to determine which part is at fault…
Step 1. Turn on your washing machine’s water and power supply.
Step 2. Run a normal wash cycle.
Step 3. Pay close attention to the washer as it fills.
Step 4. While the washer is filling with water, turn off the power supply. If the washer is still filling with water, the fault is from the inlet valve. However, if it only overfills when the washer is on, the water level sensor is defective.
Here’s how to replace the water inlet valve and the water level sensor on your LG washing machine…
How To Replace An LG Washing Machine water Inlet Valve — Front Loaders
Do the following to replace the water inlet valve on your LG front loader washing machine…
Step 1. Turn off your washing machine’s water and power supply.
Step 2. Disconnect the water supply hose/hoses from the back of your washing machine.
Step 3. Using a Philips screwdriver, remove the two screws at the back of the washer holding the top panel.
Step 4. Slide the top panel back a few inches and lift it off the washing machine.
Step 5. The water inlet valve will be found inside the washer on the other side of the water inlet port. Disconnect the solenoid wires connected to the valve (take note of the positioning of each wire).
Step 6. Using a pair of pliers, press the clamp on each hose connected to the valve and slide it out of place.
Step 7. Disconnect each hose from the water inlet valve (take note of the positioning of each hose).
Step 8. Remove the two screws securing the water inlet valve to the washer (these can be found next to the water inlet port at the back of the machine).
Step 9. Pull the water inlet valve out of the washing machine.
Step 10. Take your new water inlet valve out of its pack.
Step 11. Pop the new water inlet valve in the same position as the one you removed an secure it with the two screws.
Step 12. Connect each hose to its appropriate port on the new water inlet valve.
Step 13. Press and slide each clamp to secure the hoses to the new water inlet valve.
Step 14. Connect each solenoid wire to its appropriate terminal on the new water inlet valve.
Step 15. Place the washer’s top panel back in place and secure it with the two Philips screws.
Step 16. Connect the water supply hose/hoses to your washing machine.
Step 17. Turn on your washing machine’s water and power supply.
Step 18. Run a wash cycle to see if the issue has been resolved.
How To Replace An LG Washing Machine water Inlet Valve — Top Loaders
Do the following to replace the water inlet valve on your LG front loader washing machine…
Step 1. Turn off your washing machine’s water and power supply to avoid electrocution and water leakage.
Step 2. Using a Philips screwdriver, remove the five screws holding the back panel of the washer’s control board (three at the top and two at the bottom).
Step 3. Pull the panel off the washer.
Step 4. Detach the control housing from the washer and lay it on the machine’s lid (wire’s will still be attached to the housing).
Step 5. Disconnect the inlet hose/hoses from the water inlet valve.
Step 6. Detach the solenoid wires connected to the water inlet valve (take note of the positioning of each wire).
Step 7. Press the clamp on each hose connected to the valve and slide it out of place.
Step 8. Disconnect the hoses from the water inlet valve (take note of the positioning of each hose).
Step 9. The water inlet valve is held to the washing machine by three screws; take the screws out.
Step 10. Pull the water inlet valve out of the washing machine.
Step 11. Take your new water inlet valve out of its pack.
Step 12. Put the new water inlet valve in the same position as the on you removed.
Step 13. Secure the new valve to the washer by applying the three screws.
Step 14. Connect each hose to its appropriate port on the washer.
Step 15. Slide the each clamp in place to secure the hose to the new water inlet valve.
Step 16. Connect each solenoid wire to its appropriate terminal on the new water inlet valve.
Step 17. Connect the water supply hose/hoses to the water inlet valve.
Step 18. Reposition the control housing and put the back panel on.
Step 19. Secure the back panel by applying the five screws.
Step 20. Turn on your washing machine’s water and power supply.
Step 21. Run a wash cycle to see if the issue has been resolved.
How To Replace An LG Washing Machine Water Level Sensor — Front Loaders
Do the following to replace a water level sensor on your LG front loader washing machine…
Step 1. Turn off your washing machine’s water and power supply to avoid electrocution or water leakage.
Step 2. Using a screwdriver, take out the two screws at the back of the washing machine holding the top panel.
Step 3. With the screws removed, slide the panel back a bit and lift it off the washing machine.
Step 4. The water level sensor (or water pressure switch) can be found inside the washer near the water inlet valve. Detach the wire harness connected to the water level sensor.
Step 5. Using a screwdriver, remove the screw holding the water level sensor to the washing machine.
Step 6. Detach the tube connected to the water level sensor.
Step 7. Pull the water level sensor out of the washing machine.
Step 8. Get your new water pressure switch out of its pack.
Step 9. Secure the new water pressure switch to the washer with the mounting screw.
Step 10. Attach the little tube to the new water level sensor.
Step 11. Connect the wire harness to the new water level sensor.
Step 12. Put the washer’s top panel back in place and secure it with the two screws at the back.
Step 13. Turn on your washing machine’s water and power supply.
Step 14. Run a wash cycle to see if the issue has been resolved.
How To Replace An LG Washing Machine Water Level Sensor — Top Loaders
Do the following to replace the water level sensor on your LG front loader washing machine…
Step 1. Turn off your washing machine’s water and power supply to avoid electrocution and water leakage.
Step 2. Using a Philips screwdriver, take out the five screws holding the back panel of the washer’s control board (three at the top and two at the bottom).
Step 3. Pull the panel off the washing machine.
Step 4. Detach the control housing from the washer and lay it on the washer’s lid (some wires will be connected to the housing).
Step 5. The water level sensor will be found next to the water inlet valve. Disconnect the wire harness connected to the sensor.
Step 6. Press the tabs on the water level sensor while pulling to free it from the washing machine.
Step 7. Using a Philips screwdriver, remove the screws holding the washer’s back panel.
Step 8. Detach the panel from the washing machine.
Step 9. Release the retaining clamp on the water level sensor tube.
Step 10. Detach the water level sensor tube from the washer’s tub.
Step 11. Reposition the control housing on top of the washer.
Step 12. Open the lid of your washing machine.
Step 13. Using a putty knife, release the clips holding the main top of the washing machine.
Step 14. Lift the washer’s main top and support it.
Step 15. To release the tube from the wire harness, cut the cloth tape holding it.
Step 16. Untwist the upper retaining wire holding the tube.
Step 17. Pull the water level sensor and tube out of the washing machine.
Step 18. Get your new water level sensor out of it’s pack.
Step 19. Insert the water level sensor’s tube through the base of the control housing.
Step 20. Connect the tube to the washer’s tub and secure it using the clamp.
Step 21. Using the upper retaining wire, secure the tube to the main wire harness.
Step 22. Lower the main top of the washing machine and snap it in place.
Step 23. Close the lid of your washing machine.
Step 24. Detach the control housing once more and lay it on the washer’s lid.
Step 25. Snap the new water level sensor in place on the washer’s control base.
Step 26. Attach the electrical connector to the new water level sensor.
Step 27. Reposition the rear main panel of your washing machine and secure it by reapplying the screws.
Step 28. Reposition the washer’s control housing.
Step 29. Put the back panel of the washer’s control in place and secure it with the five screws.
Step 30. Turn on your washing machine’s water and power supply.
Step 31. Run a wash cycle to see if the issue has been resolved.
Note: Please keep in mind that this repair can get a bit complex. If you aren’t confident in your washer repair skills, we strongly advise against attempting this repair by yourself.
LG Washing Machine Error Code DHE — How To Fix
An LG washing machine DHE error code indicates a temporary glitch with the dryer system. To fix this issue, all you need to do is turn off your washing machine’s power supply for about ten minutes and then plug it back in. This will clear any system glitches in the washer.
LG Washing Machine Error Code DE2 — Solution
A DE2 error code on your washer indicates that the door of the machine is closed but not locking. This issue occurs when the machine’s door lock is defective. You’ll need to replace the lock to clear this error code. Do the following to replace the door lock of your LG washing machine…
Step 1. Turn off your washing machine’s water and power supply to avoid electrocution or water leakage.
Step 2. Open the door of your washing machine.
Step 3. There is a retaining wire around the gray door seal; you’ll need to get a flat-blade screwdriver to take it out.
Step 4. Wedge the screwdriver under the wire and work your way around until you can take the whole wire out.
Step 5. Peel the door seal to your left away from the door lock.
Step 6. Using a Philips screwdriver, remove the two screws holding the door lock in place (make sure to support the door lock with your hand from inside the washer).
Step 7. Detach the electrical connectors attached to the door lock assembly.
Step 8. Pull the door lock out of the washing machine.
Step 9. Get your new door lock out of its pack.
Step 10. Install the new door lock and secure it to the washer with the two screws.
Step 11. Connect the electrical connector to the new door lock assembly.
Step 12. Push the door seal back in place.
Step 13. Fit the retaining band around the door seal (you may need a flat-blade screwdriver to help you do this).
Step 14. Close the door of your washing machine.
Step 15. Turn on your washing machine’s water and power supply.
Step 16. Run a wash cycle to see if the issue has been resolved.
LG Washing Machine Error Pre-wash And Crease Care Blinking — Solved
If the pre-wash and crease care lights on your lg washing machine are blinking, the water inlet filter is at fault. Here’s how to fix this issue on your washing machine…
Step 1. Turn off your washing machine’s water and power supply to avoid water leakage or electrocution.
Step 2. Disconnect the water supply hose from the back of your washing machine.
Step 3. You’ll find a little mesh filter in the water inlet port at the back of the washer. Take the filter out with a pair of pliers.
Step 4. Take the filter to a sink and rinse out any debris that may have accumulated in it.
Step 5. Once the filter is clean, put it back in place.
Step 6. Connect the water supply hose to the back of the washing machine.
Step 7. Turn on your washing machine’s water and power supply.
Step 8. Run a wash cycle to see if the issue has bee resolved.
LG Washing Machine Error Code Key Symbol — Solution
The key symbol on your LG washing machine can mean different things. Most times it indicates that the Child Lock feature is on. It may also indicate that the temperature of the water in the machine is too high.
If the symbol appeared as a result of the Child Lock feature being on, you’ll need to deactivate the function.
To deactivate the Child lock feature on your LG washer, press the Rinse and Spin buttons simultaneously and hold for about 3 seconds. Depending on the model of your washer, there may be a Child Lock button on the control panel. Consult your manual if neither of these methods worked for you.
If the key symbol popped up as a result of the water temperature being too high, all you need to to do is turn off your washing machine for a while until the system cools down.