If you are having trouble with your Whirlpool washing machine draining, you’ve come to the right place; this detailed guide explains the causes of this issue and gives you steps on how to fix them…
Table of Contents
How To Replace Whirlpool Washing Machine Drain Hose — Solved
The steps below show you how to replace the drain hoses in your Whirlpool washing machine…
1. Main Drain Hose
Follow the steps below to replace the main drain hose in your Whirlpool washing machine…
Step 1. Ensure that your washing machine is disconnected from the outlet before starting this repair in order to prevent electrocution.
Step 2. Go to the back of the machine, then pull the drain hose out of the standpipe. Using pliers, release the clamp holding the other end of the hose to the machine.
Step 3. Pull the drain hose off the cabinet and discard it. Prepare your new washing machine drain hose for installation by taking it out of its packaging.
Step 4. One end of the drain hose to the cabinet, then use your pliers to slide the spring clamp into place.
Step 5. Insert the other end of the new drain hose into your home drain. Plug the washing machine into the electrical outlet, then make sure everything works properly by running a wash cycle.
2. Tub-To-Pump Hose
Follow the steps below to replace the sump hose in your Whirlpool washing machine…
Front Loaders
Take the following steps to replace the sump hose in your front loader Whirlpool washing machine…
Step 1. Make sure to turn off your washing machine’s water supply faucets and disconnect the power cord from the outlet before starting this repair.
Step 2. Use a pair of pliers to disconnect the two water supply hoses from the ports at the back of the machine (some water will spill out, so ensure that you keep a rag nearby).
Step 3. Pull your washing machine’s drain hose out of the standpipe. Move the washing machine forwards a bit to get more working space.
Step 4. Go to the front of the appliance. Using a 1/4 inch nut-driver, loosen the screws holding the lower front access panel to the cabinet. Pry the panel off the machine and set it aside.
Step 5. Got to the back of the washer, then use your 1/4 inch nut-driver to take out the screws holding the rear panel.
Step 6. Pry out the four plastic plugs at the back of the machine. Lift the rear access panel, then pull it off the cabinet.
Step 7. Go back to the front of the machine, then spread a rag on the floor. Place a container underneath the pump filter knob at the lower front section of the appliance.
Step 8. Rotate the pump filter knob, then let any water and debris stuck in the pump drain out.
Step 9. Once all the water has drained out of your washing machine, put the pump filter back in place and rotate it to secure.
Step 10. Using your pliers, release the spring clamp holding the internal drain hose to the drain pump. Pull the hose off the pump.
Step 11. With your 1/4 inch nut-driver, loosen the screws holding the pump assembly to the bottom of the cabinet.
Step 12. Move the drain pump out of place. Unplug the electrical connector attached to the drain pump assembly. Rotate the drain pump to gain access to the sump hose.
Step 13. With a pair of pliers, squeeze the clamp holding the sump hose to the pump assembly, then slide it out of place. Detach the sump hose from the pump (some water may spill out).
Step 14. Go to the back of the machine. Use your pliers to release the spring clamp securing the other end of the sump hose to the bottom of the tub. Pull the hose off the tub assembly.
Step 15. Take the drain hose out of the cabinet and discard it. Prepare your new washing machine sump hose for installation by taking it out of its packaging.
Step 16. Attach one end of the new sump hose to the port at the bottom of the tub, then secure it using the spring clamp.
Step 17. Go to the front of the appliance, then connect the other end of the sump hose to the drain pump assembly, then use the retaining clamp to secure it.
Step 18. Reconnect the internal drain hose to the port on the drain pump, then slide the spring clamp into place.
Step 19. Mount the drain pump onto the floor of the cabinet, then secure it by applying the nuts with your 1/4 inch nut-driver.
Step 20. Snap the lower front access panel back onto the cabinet, then apply the three screws at the bottom to secure it.
Step 21. Go to the back of the machine and mount the rear access panel onto the machine. Secure the rear panel by applying the screws with your 1/4 inch nut-driver.
Step 22. Snap the four plastic transit caps onto the rear panel. Reconnect the COLD and HOT water supply hoses to the ports at the back of the machine (in order to prevent any chances of water leakage, make sure to secure the hoses properly).
Step 23. Move your washing machine back into place, then turn the water supply faucets back on.
Step 24. Plug the machine’s power cord back into the electrical outlet, then try running a wash cycle to make sure everything works properly.
Top Loaders
Follow the steps below to replace the sump hose in your top loader Whirlpool washing machine…
Step 1. Turn off your washing machine’s HOT and COLD water supply faucets, then unplug the power cord from the outlet (this will prevent electrocution and water leakage).
Step 2. Use a pair of pliers to release the spring clamp holding the outlet hose to the port at the back of the machine. Detach the drain hose from your washing machine.
Step 3. Spread a towel on the floor underneath the water inlet hoses in order to catch any leaks. Disconnect the inlet hoses from the ports at the back of the machine.
Step 4. Put some tape on the washer’s lid to secure it. Tip the washing machine backwards carefully and set it on the floor (if needed, have someone assist you).
Step 5. Using your pliers, squeeze the spring clamp holding the sump hose to the bottom of the tub, then move it out of place. Disconnect the sump hose from the tub.
Step 6. Release the clamp at the other end of the hose, then move it out of place. Disconnect the sump hose from the drain pump assembly (some water will spill).
Step 7. Discard the old hose and take the new one out of its packaging. Attach on end of the new sump hose to the pump, then secure it using the spring clamp.
Step 8. Attach the other end of the sump hose to the port at the bottom of the tub. Slide the spring clamp into place to secure the connection.
Step 9. Carefully lift the washing machine back onto its feet, then peel the tape off the lid.
Step 10. Reconnect the drain hose to the port at the back of the washer. Secure the drain hose with the retaining clamp.
Step 11. Reattach the HOT and COLD water inlet hoses to the appropriate ports at the back of your washing machine.
Step 12. Reconnect your appliance to the electrical outlet, then turn the water supply valves back on. Make sure everything works normally by running a wash cycle.
Check out these other articles…
How To Move A Washing Machine [Detailed Guide]
Whirlpool Washing Machine Error Codes [How To Fix]
Whirlpool Washing Machine Not Spinning [How To Fix]
Whirlpool Washing Machine Spinning [Problems & Solutions]
How To Clean Whirlpool Washing Machine [Detailed Guide]
How To Replace A Whirlpool Washing Machine Door Seal [Detailed Guide]
Washer/Dryer Combo Machine
Follow the steps below to replace the sump hose in your Whirlpool washer/dryer combo machine…
Step 1. Disconnect the appliance from the outlet before starting this procedure, in order to prevent electrocution.
Step 2. Take out the screws holding the dryer compartment’s lower access panel using a Philips screwdriver. Lift the panel off the cabinet and set it aside.
Step 3. Slide the two access panel clips out of place. Using your 1/4 inch nut-driver, loosen the bolts holding the two panels to the machine.
Step 4. With a flat-blade screwdriver, pry out the two spring clips holding the top panel to the machine. Slide the top assembly forwards a few inches, then lift it off the cabinet.
Step 5. Take out the bolt holding the support bar to the front panel using a 5/16 inch nut-driver. Move the bar out of place.
Step 6. Take out the screws at the back side of the front panel using your nut-driver. Pull the front panel upwards, then lift it off the cabinet.
Step 7. Use a pair of pliers to release the clamp holding the sump hose to the drain pump, then move it out of place. Disconnect the sump hose from the drain pump (make sure to keep a rag nearby to clean any water leaks).
Step 8. Release the clamp holding the other end of the hose to the tub. Disconnect the sump hose from the bottom of the tub.
Step 9. Discard the sump hose, then take the new one out of its packaging. Connect the new sump hose to the ports on the drain pump and tub. Move the two spring clamps into place to secure the connection.
Step 10. Lift the front panel and remount it on the cabinet. Apply the bolts at the back of the panel using a 5/16 inch socket wrench.
Step 11. Move the support bar onto the front panel, then apply the screw to secure it. Place the top panel on the cabinet, then slide it into place.
Step 12. Use a flat-blade screwdriver to push the spring clips back into the slots on the top panel.
Step 13. Put the two access panels back in place, then secure them by applying the nuts with your 1/4 inch nut-driver. Slide the two access panel clips into the slots.
Step 14. Remount the lower access panel of the dryer compartment, then apply the screws using your Philips screwdriver.
Step 15. Plug your washing machine back into the power outlet, then ensure that the appliance works properly by running a cycle.
3. Internal Drain Hose
To replace the internal drain hose in your Whirlpool washing machine, follow the steps below…
Front Loaders
Do the following to replace the internal drain hose in your Whirlpool front loader washing machine…
Step 1. In order to prevent any chances of electrical damage, it is advised that you disconnect your washing machine from the power outlet before starting this repair.
Step 2. Pry out the four plastic plugs at the back of your washing machine. Use a 1/4 inch nut-driver to loosen the nuts holding the rear panel to the cabinet.
Step 3. Pry the rear panel off the machine, then set it aside. With a pair of pliers, release the spring clamp securing the internal drain hose to the pump assembly.
Step 4. Detach the internal drain hose from the pump (some water may spill out). Release the spring clamp holding the main drain hose to the port at the back of the cabinet.
Step 5. Detach the main drain hose from the back of the machine. Release the tabs holding the internal drain hose mounting connector to the cabinet using a flat-blade screwdriver.
Step 6. Release the internal drain hose from the retainers on the cabinet, then take it out of the machine.
Step 7. Slide the spring clamp off the old internal drain hose, then transfer it to the new one.
Step 8. Snap the mounting connector of the new internal drain hose into the opening at the back of the cabinet.
Step 9. Secure the new hose in the retainers, then attach the other end to the drain pump.
Step 10. Lift the rear panel and mount it on the cabinet. Secure the rear panel by applying the nuts with your 1/4 inch nut-driver.
Step 11. Snap the four plastic caps into the slots at the back of your machine. Plug the machine into the power outlet, the try running a wash cycle to make sure everything works normally.
Top Loaders
Follow the steps below to replace the internal drain hose in your top loader Whirlpool washing machine…
Step 1. Prevent any chances of electrocution by unplugging your washing machine from the outlet before starting this repair.
Step 2. With the help of another person, move the washing machine forwards a bit to get more working space.
Step 3. Using a 1/4 inch nut-driver, loosen the screw holding the wiring and tube guard to the rear panel.
Step 4. Use your pliers to release the clamp holding the main drain hose to the back of the washing machine. Disconnect the drain hose from the washer.
Step 5. Use your 1/4 inch nut-driver to loosen the seven screws holding the main rear access panel of your washer.
Step 6. Loosen the nut on the rear panel securing the internal drain hose. Lift the rear access panel off the cabinet, then set it aside.
Step 7. With your nut-driver, loosen the nut securing the retainer holding the internal drain hose to the side of the tub.
Step 8. Use your pliers to release the spring clamp holding the internal drain hose to the pump assembly. Disconnect the drain hose from the pump.
Step 9. Take the spring clamp off the old drain hose, then discard the hose. Take your new internal drain hose out of its packaging.
Step 10. Transfer the spring clamp from the old hose to the new one. Attach one end of the new hose to the port on the drain pump, then slide the clamp into place.
Step 11. Secure the new hose in the retainer, then apply the bolt to secure the retainer to the tub.
Step 12. Place the rear access panel on the cabinet, then apply the seven screws to secure it. Secure the connector of the new hose to the rear panel by applying the nut.
Step 13. Connect the main drain hose to the port at the back of the cabinet, then slide the retaining clamp into place.
Step 14. Put the wiring and tube guard back in place, then use your 1/4 inch nut-driver to apply the screws.
Step 15. Plug your washing machine into the electrical outlet. Run a wash cycle to ensure that everything works properly.
Washer/Dryer Combo
Follow the steps below to replace the internal drain hose in your Whirlpool washer/dryer combo washing machine…
Step 1. Make sure to disconnect your washing machine’s power cord from the electrical outlet in order to prevent electrocution.
Step 2. Using your Philips screwdriver, take out the nuts holding the lower access panel to the dryer compartment. Pull the panel off the machine and set it aside.
Step 3. Slide the two access panel clips out of the slots and set them aside. Use a 1/4 inch socket wrench to loosen the four screws holding the two access panels to the machine.
Step 4. Take the access panels of the machine and set them aside. With your flat-blade screwdriver, pry out the two spring clips holding the top panel to the machine.
Step 5. Pull the top panel forwards a few inches, then lift it off the cabinet. Use a 5/16 inch socket wrench to loosen the bolt securing the support bar to the front panel. Move the bar out of place.
Step 6. Using the nut-driver, take out the screws at the back of the front panel securing it to the cabinet. Pull the panel upwards, then lift it off the cabinet.
Step 7. Reach behind the tub and use a pair of pliers to release the spring clamp holding the internal drain hose to the port at the back of the cabinet. Detach the hose from the port.
Step 8. Spread a towel on the floor underneath the drain pump to catch any leaks. Use your pliers to release the spring clamp holding the other end of the internal drain hose to the pump.
Step 9. Detach the hose from the drain pump. Slide the clamps off the internal drain hose. Discard the old hose and take the new one out of its packaging.
Step 10. Transfer the clamps from the old hose to the new one. Connect one end of the new internal drain hose to the port on the drain pump, then slide the spring clamp into place to secure the connection.
Step 11. Attach the other end of the new hose to the port at the back of the cabinet. To secure the connection, move the retaining clamp into place.
Step 12. Carefully lift the front panel and remount it on the cabinet. Apply the screws at the back of the cabinet using a 5/16 inch nut-driver.
Step 13. Move the support bar back onto the front panel, then use your nut-driver to apply the screws.
Step 14. Place the top panel on the washer, then slide it forwards. Push the two retaining clips into the slots using a flat-blade screwdriver.
Step 15. Put the two access panels back on, then secure them by applying the four screws with your 1/4 inch socket wrench.
Step 16. Slide the two access panel clips back into the slots. Remount the dryer compartment’s lower access panel, then apply the nuts using your Philips screwdriver.
Step 17. Plug the machine’s power cord back into the electrical outlet, then ensure that everything works normally by running a wash cycle.
Whirlpool Washing Machine Draining All The Time — Quick Fix
Is your Whirlpool washing machine draining all the time? Here are the issues to look for…
1. Glitching Control Board
If your washing machine is draining all the time, the first thing you should check is the control board. If the board gets damaged or has a fault, it could cause your washer to keep draining.
2. Damaged Drain Pump Assembly
Another thing that can cause your Whirlpool washing machine to keep draining is a cracked pump assembly. Before deciding on whether you need to replace the pump, you should inspect it for damage. Here’s how to do this…
Top Loaders
The steps below show you how to inspect the drain pump in your top loader Whirlpool washing machine…
Step 1. In order to prevent water leaks and electrocution, make sure to unplug the power cord from the outlet and turn the water faucets off before starting this procedure.
Step 2. With a pair of pliers, squeeze the clamp securing the main drain hose to the port at the back of the washer, then move it out of place. Disconnect the hose from the machine (some water may spill out).
Step 3 Spread a rag on the floor under the water supply lines to catch any leaks. Loosen the two hoses from the inlet ports on the machine.
Step 4. Place some tape on the lid of your washing machine to help secure it. With someone else assisting you, tip the washer backwards carefully and set it on the floor.
Step 5. Use your pliers to release the spring clamps holding the hoses to the pump assembly. Disconnect each hose from the drain pump (make sure to keep a cloth nearby).
Step 6. Use a 5/16 inch nut-driver to loosen the bolts holding the drain pump to the bottom of the tub.
Step 7. Pull the pump off the tub and inspect it for cracks. Insert a flat-blade screwdriver into the ports of the pump and look for any signs of damage.
Step 8. Once you are sure that the drain pump is in good condition, remount it on the tub, then apply the screws to secure it.
Step 9. Reattach the two drain hoses to the appropriate ports on the pump, slide the retaining clamp into place to secure the hoses.
Step 10. Get someone to help you lift the washing machine back onto its feet. Peel the tape off the lid, then reconnect the main drain hose to the outlet port.
Step 11. Attach the two water supply hoses to their corresponding ports at the back of the washing machine (make sure both hoses are secured properly in order to prevent leaks).
Step 12. Plug the machine back into the outlet, then turn the water faucets back on. To ensure that everything works normally, try running a cycle.
Front Loaders
To inspect the drain pump assembly in your front loader Whirlpool washing machine, follow the steps below…
Step 1. Ensure that your washing machine is disconnected from the outlet before starting this procedure, in order to prevent electrical damage.
Step 2. Go to the front of the appliance, then loosen the three screws at the bottom of the lower access panel using a 1/4 inch socket wrench. Lift the panel off the machine and set it aside.
Step 3. Spread a towel on the floor in front of the machine to catch any leaks. Turn the pump filter knob and let any water stuck in the machine drain out.
Step 4. Using a pair of pliers, squeeze the metal clamps holding the sump and internal drain hoses to the ports on the pump, then move them out of place.
Step 5. Disconnect each hose from the drain pump assembly. Use a 1/4 inch socket to loosen the screws holding the drain pump assembly to the bottom of the cabinet.
Step 6. Move the pump assembly out of place, then inspect it for any signs of damage or cracking.
Step 7. Once you are satisfied that the pump is in good condition, remount it on the cabinet, then apply the bolts to secure it.
Step 8. Connect each hose to its appropriate terminal on the pump assembly, then slide the spring clamps into place.
Step 9. Put the pump filter back into the housing, then rotate it to secure. Snap the lower access panel back onto the cabinet, then apply the screws at the bottom to secure it.
Step 10. Plug the washer’s power cord into the electrical outlet. To ensure everything works properly, try running a wash cycle.
Washer/Dryer Combo
Follow the steps below to inspect the drain pump assembly in your washer/dryer combo machine…
Step 1. In order to prevent any chances of electrocution, ensure that your washing machine is disconnected from the power outlet before starting this repair.
Step 2. Use a Philips screwdriver to loosen the screws holding the lower access panel to the dryer compartment. Pry the panel off the machine and set it aside.
Step 3. Pull the two access panel clips out of the slots on the top panel. Use a 1/4 inch socket wrench to loosen the screws holding the access panels to the machine.
Step 4. Pull the panels off the cabinet and set them aside. With a flat-blade screwdriver, pry out the spring clamps securing the top panel to the cabinet.
Step 5. Slide the top panel forwards a few inches, then lift it off the cabinet. Loosen the bolt holding the support bar to the front panel. Move the bar out of position.
Step 6. Using a 5/16 inch socket wrench, take out all the screws at the back of the washer’s front panel.
Step 7. Pull the panel upwards carefully, then lift it off the cabinet. Using your flat-blade screwdriver, pry off the two clips holding the drain pump to the motor shaft.
Step 8. Slide the pump assembly off the motor shaft. Inspect the drain pump for cracks or damage.
Step 9. Once you’ve ensured that the pump is in good condition, slide it back onto the motor shaft, then snap the two retaining clamps back on.
Step 10. Lift the front panel and mount it on the cabinet. Use your 5/16 inch nut-driver to apply the screws at the back of the panel.
Step 11. Move the support bar back into place, then apply the screw with your nut-driver.
Step 12. Mount the top panel on the cabinet, then slide it into place. Use your flat-blade screwdriver to push the two spring clips into the slots on the top panel.
Step 13. Place the access panels on the machine, then apply the nuts to secure them. Fit slide the two access panel clips into the openings.
Step 14. Remount the lower access panel on the cabinet, then apply the screws at the bottom to secure it.
Step 15. Plug your washing machine back into the electrical outlet, then make sure everything works normally by running a wash cycle.
If you noticed any damage to the drain pump assembly in your washing machine, you’ll need to replace it. For detailed steps on how to do this, read this article Whirlpool Washing Machine Error Codes. This guide will also give you steps on how to deal with other issues in your Whirlpool washing machine.