If your Amana washing machine stops at various points and you don’t know what to do, you’ve come to the right place. This detailed guide explains the causes of these issues and gives you steps on how to resolve them
So, without wasting any more time, let’s get right to it…
Table of Contents
Amana Washing Machine Stops In The Middle Of A Cycle — Solved
If your Amana washing machine stops in the middle of a cycle, it indicates that something is preventing your washing machine from draining. Here’s what you’ll need to do to fix drainage issues in your Amana washing machine…
1. Blocked Pump Filter (Front Loaders)
Take the following steps to clean the pump filter in your Amana front loader washing machine…
Step 1. In order to prevent electrical damage, make sure your washing machine is disconnected from the electrical outlet.
Step 2. Use a 1/4 inch nut-driver to remove the screws securing your machine’s rear access panel. Lift the panel off the cabinet and set it aside.
Step 3. Place a rag on the floor of the cabinet underneath the drain pump. Place a small container underneath the drain pump.
Step 4. Turn the knob on the pump assembly and take it out (a lot of water will pour out).
Step 5. Take the filter to a sink and clean out any accumulated dirt in it. Use a rag to clean the housing on the drain pump assembly.
Step 6. Once everything has been cleaned, put the filter back in place and turn it to secure.
Step 7. Put your machine’s rear access panel back on and apply the screws to secure it. Connect the power cord back to the electrical outlet and ensure the issue has been fixed by running a wash cycle.
2. Damaged Drain Pump Assembly
To replace a damaged drain pump assembly in your Amana washing machine, here are the steps you’ll need to take…
How To Change Amana Top Loader Washing Machine Drain Pump
Replace the pump assembly in your top loader Amana washing machine with the following steps…
Step 1. Shut your washer’s water supply valve and disconnect the power cord from the electrical outlet before starting this repair in order to prevent electrical damage or water leakage.
Step 2. Put some tape on the lid of your machine to secure it. Release the spring clamp on the drain hose at the back of the machine. Pull the hose off the machine.
Step 3. Use a pair of pliers to disconnect the COLD and HOT water supply hoses from the ports at the back of your washing machine (some water will spill out, so make sure to spread a rag underneath the hoses).
Step 4. With the help of another person, tip your washing machine backwards carefully and lay it on the floor.
Step 5. Unplug the wire connector from the drain pump. Using your pliers, squeeze the clamp on the hose attached to the pump and slide it out of place. Pull the hose off the pump assembly (keep a rag nearby to clean any water leaks).
Step 6. With a 5/16 inch nut-driver, remove the screws holding the pump assembly to the bottom of the outer tub. Take the drain pump off the machine and discard it.
Step 7. Remove your new washing machine drain pump from its packaging. Mount the new pump assembly at the bottom of your machine and secure it by applying the bolts with your nut-driver.
Step 8. Plug the wire harness into the terminal on the new pump assembly. Attach the outlet hose to the port on the new pump assembly. Secure the hose by sliding the spring clamp into place.
Step 9. With the help of another person, carefully set your machine upright and peel the tape off the lid.
Step 10. Reattach the drain hose to the back of your machine and slide the retaining clamp into place to secure it.
Step 11. Reattach the HOT and COLD water supply hoses to the ports at the back of your washing machine.
Step 12. Reconnect your washing machine to its electrical outlet and turn the water valve back on. Try running a wash cycle to make sure the problem has been fixed.
How To Change Amana Front Loader Washing Machine Drain Pump
To change the pump assembly in your Amana front loader washing machine, here are the steps you’ll need to take…
Step 1. Unplug your washing machine from the power outlet before starting this repair in order to prevent electrical damage.
Step 2. Loosen the bolts at the back of your machine using a 1/4 inch nut-driver. Lift the panel off the cabinet and set it aside.
Step 3. Disconnect the wire harness attached to the drain pump assembly underneath the tub.
Step 4. Use your pliers to release the clamp on the hose attached to the pump and slide it out of place. Spread a rag on the floor of the cabinet underneath the drain pump. Pull the hose off the pump.
Step 5. Use a nut-driver to remove the screws securing the pump to the bottom of the outer tub. Take the pump out of the cabinet and discard it.
Step 6. Remove your new washing machine drain pump from its packaging. Mount the new pump at the bottom of the outer tub and secure it by applying the bolts with your nut-driver.
Step 7. Plug the wire connector into the new pump assembly. Connect the hose to the pump and secure it using the spring clamp.
Step 8. Put your washer’s rear panel back on and use a nut-driver to apply the bolts. Plug your washing machine back into the electrical outlet and ensure the issue has been fixed by running a wash cycle.
Amana Washing Machine Stops Full Of Water — Quick Fix
If your Amana washing machine stops full of water, it could indicate that the lid isn’t firmly shut. Most Amana washing machine’s will not go past the fill cycle unless the lid is locked.
Please keep in mind that this applies only to top loaders. Front loader washing machine’s won’t start any cycle unless the door is locked.
If your washing machine lid isn’t locking, you’ll need to replace the lock assembly. Here’s how to do this…
Step 1. Prevent electrocution and water leakage by disconnecting your washing machine from the electrical outlet and turning the water valve off before starting this repair.
Step 2. Spread a rag underneath the two fill hoses at the back of your washing machine. Unscrew the hoses from your washer (water will spill out).
Step 3. Put some tape on the lid of your machine to secure it. Use a 1/4 inch nut-driver to remove the bolts at the back of the machine securing the control panel rear access cover. Take the cover off the machine and set it aside.
Step 4. Disconnect the wire harness of the lid lock from the terminal on the control board. Release the wire from the retainer using a flat-blade screwdriver.
Step 5. Take out the screws holding the top panel to the cabinet. Lift the top panel and support it.
Step 6. Use a flat-blade screwdriver to release the lid lock wire from the retainers at the bottom of the top panel.
Step 7. Remove the screws holding the lid lock to the top panel using a Philips screwdriver. Take the lid lock assembly off the machine and discard it.
Step 8. Remove your new washing machine lid lock assembly from its packaging. Mount the new lid lock at the bottom of the top panel and apply the screws with your Philips screwdriver.
Step 9. Secure the lid lock wire in the retainers on the top panel. Pass the wire connector through the opening on the top panel.
Step 10. Lower the top panel onto the cabinet and apply the bolts at the back to secure it.
Step 11. Plug the wire connector into the control board and secure the wire in the retainer.
Step 12. Put the control panel’s rear access cover back on and apply the screws using your screwdriver.
Step 13. Reconnect the two water supply lines to the ports at the back of your machine.
Step 14. Turn the water valve back on and plug the power cord into the electrical outlet. To ensure that the problem has been fixed, try running a wash cycle.
Check out these other articles…
Amana Washing Machine Shakes Violently [Proven Solution]
Amana Washing Machine Squeaking [How To Fix]
Amana Washing Machine Not Turning On [Proven Solutions]
Washing Machine Motor [How To, Issues & Solutions]
No Lights On My Amana Washer [Quick Fix]
Amana Washing Machine Stops At Rinse — Solved
If your Amana washing machine stops at the rinse cycle, it indicates that something is preventing the drum from filling. here are the problems to look for…
1. Water Inlet Valve Failed
Follow the steps below to replace the inlet valve in your Amana washing machine…
How To Change Damaged Amana Front Loader Washing Machine Water Inlet Valve
To replace a failed inlet valve in your front loader Amana washing machine, here are the steps you’ll need to take…
Step 1. Unplug your washing machine from its electrical outlet and shut the water supply in order to prevent water leakage and electrical damage.
Step 2. Unscrew the COLD and HOT water supply hoses from the ports at the back of your machine (make sure to spread a towel underneath the hoses in case water spills).
Step 3. Use a 1/4 inch nut-driver to remove the bolts holding the top panel to the cabinet. Pull the panel backwards about an inch or so, and lift it off the machine.
Step 4. Disconnect the wire connectors attached to the inlet valve assembly. Release the spring clamp on the internal hose attached to the valve and pull the hose off.
Step 5. With your Philips screwdriver, remove the screws at the back of the machine securing the valve to the cabinet. Pull the valve assembly out of the cabinet and discard it.
Step 6. Prepare your new washing machine valve for installation by removing it from its packaging.
Step 7. Install the inlet valve in the cabinet and apply the screws with your Philips screwdriver.
Step 8. Plug the solenoid wire connectors into the terminals on the new valve. Attach the internal hose to the new valve and secure it using the spring clamp.
Step 9. Place the top place back on the cabinet and apply the screws using your nut-driver.
Step 10. Connect the two water inlet hoses back to the ports on your machine (make sure you secure both hoses properly so water won’t spill).
Step 11. Connect your washing machine back into the electrical outlet and turn the water supply valve back on. To make sure the problem has been fixed, try running a wash cycle.
How To Change Damaged Amana Top Loader Washing Machine Water Inlet Valve
Take the following steps to change a failed inlet valve in your Amana top loader washing machine…
Step 1. In order to prevent water leakage and electrocution, make sure to disconnect your washing machine from its power outlet and turn the water valve off before starting this repair.
Step 2. Unscrew the two inlet hoses from the back of your machine using a pair of pliers (you should keep a rag nearby in case water spills out).
Step 3. Release the two spring clips under the control panel using a putty knife. Set the top panel on the cabinet facing downwards.
Step 4. Disconnect the wire connector of the water inlet valve from the control board. Use a screwdriver to remove the screws holding the inlet valve to the cabinet.
Step 5. Pull the inlet valve out of the machine and discard it. Remove your new washing machine water inlet valve assembly from its packaging.
Step 6. Install the new inlet valve in the machine and apply the screws with your Philips screwdriver.
Step 7. Plug the wire harness of the new inlet valve into the control board. Lift the control panel and snap it back into the cabinet.
Step 8. Reattach the HOT and COLD water supply hoses to the ports at the back of your washer (in order to prevent water leaks, make sure both hoses are secured properly).
Step 9. Plug your washing machine back into the electrical outlet and turn the water supply valve back on. Ensure that the problem has been fixed by running a wash cycle.
2. Control Board Glitch
If your Amana washing machine stops at the rinse cycle, it could be as a result of a control board glitch. Try disconnecting your machine from the outlet for about 10 minutes and plug it back in.
If the issue persists, you’ll need to replace the control board. Here are the steps you’ll need to take to do this…
How To Change Amana Front Loader Washing Machine Control Board
Replace a damaged control board in your Amana front loader washing machine with the following steps…
Step 1. Unplug your washing machine’s power cord from the electrical outlet in order to prevent electrocution.
Step 2. Loosen the bolts at the back of your machine securing the top panel. Pull the panel backwards backwards about an inch or so, then lift it off the cabinet.
Step 3. Pull the cap off the control board mounted on the cabinet. Unplug each wire connector from the terminals on the control board (make sure to note where each connector goes). release the wires from the retainers.
Step 4. Using your flat-blade screwdriver, pry the control board off the cabinet mount and discard it.
Step 5. Prepare your new control board for installation by removing it from its packaging.
Step 6. Snap the new control board into the mounts on the cabinet. Plug each wire connector into its appropriate terminal on the new board. Secure the wires in the control board retainers.
Step 7. Place the top panel on the machine and use your nut-driver to apply the bolts. Reconnect your washing machine to its electrical outlet. To ensure that the problem has been fixed, try running a wash cycle.
How To Change Amana Top Loader Washing Machine Control Board
Do the following to replace a faulty control board in your top loader Amana washing machine…
Step 1. Prevent any chances of electrical damage by disconnecting the machine from its power outlet before starting this repair.
Step 2. Release the control panel from the cabinet by inserting a tool such as a putty knife underneath the two bottom corners. Set the control panel face down on the cabinet.
Step 3. Disconnect all the electrical plugs attached to the board (make sure you note where each one goes). Release the wires from the retainers using a flat-blade screwdriver.
Step 4. Pull the air pressure tube off the port on the board. Lift the control panel and pull the selector knob off the shaft.
Step 5. Using your Philips screwdriver, take out the nuts holding the control board to the panel. Discard the old control board and take the new one out of its packaging.
Step 6. Mount the new control board on the panel and secure it by applying the screws with your Philips screwdriver.
Step 7. Lift the control panel and snap the selector knob onto the shaft. Plug each wire harness into its corresponding terminal on the new board. Secure the wires in the retainer.
Step 8. Plug the air pressure tube into the port on the new control board. Lift the control panel assembly and snap the spring clips back into the cabinet.
Step 9. Reconnect your washing machine to its power supply. To ensure that the issue has been fixed, test the machine with a wash cycle.
Amana Washing Machine Stops On Final Spin — How To Fix
If your Aman washing machine stops on the final spin cycle, it indicates that the timer is defective and needs to be replace. Here’s how to do this…
Step 1. In order to prevent electrical damage and water leaks, make sure your washing machine is disconnected from the power outlet and the water valve is turned off before starting this repair.
Step 3. Use a putty knife to release the spring clips at the bottom of the control panel. Lift the control panel and let it hang over the rear panel.
Step 4. Using a pair of needle-nosed pliers, squeeze the little knob at the back of the timer. While squeezing, pull the timer knob and dial off the control panel.
Step 5. Use a flat-blade screwdriver to pry the two electrical connectors off the timer assembly.
Step 6. Release the plastic tab holding the timer to the control panel using a flat-blade screwdriver. Take the timer off the panel and discard it.
Step 7. Remove your new washing machine timer from its packaging. Snap the new timer into place on the control panel and plug the two wire connectors in to the appropriate terminals.
Step 8. Snap the timer knob and dial back onto the control panel. Snap the spring clips on the control panel into the cabinet.
Step 9. Plug your washing machine back into the electrical outlet and turn the water valve back on. To make sure that the issue has been fixed, try running a wash cycle.