Is your Amana washing machine not filling with water? If so, you’ve come to the right place. This detailed guide will list the things that could prevent your washer from filling and give you easy-to-follow steps on how to fix them. So, without wasting any more time, let’s get right to it…
Table of Contents
Amana Washing Machine Not Filling With Water — Solved
Is your Amana washing machine not filling with water? If so, look for the following issues…
1. Water Supply Isn’t On
This is the most obvious cause. If your washing machine isn’t filling, you should check to ensure that the water supply valve is turned on.
2. Clogged Water Inlet Filters
Over time, dirt can build up in the inlet filters and prevent the machine from filling. Here’s how to clean clogged water inlet filters in your Amana washing machine…
Step 1. Prevent electrocution and water leakage by shutting your washing machine’s water supply and unplugging the power cord from the outlet before starting this repair.
Step 2. With a pair of pliers, unscrew the two water inlet hoses from the inlet ports at the back of your washing machine (make sure to have a rag nearby to clean any water spillage).
Step 3. Use a pair of needle-nosed pliers to pull out the little mesh filters in each of the inlet ports.
Step 4. Take the filters to a sink and thoroughly clean out any dirt and debris that may be clogging them. Once the filters are cleaned, push them back into place.
Step 5. Connect the two inlet hoses back to the ports on your washing machine (make sure to secure the hoses properly so water can’t leak).
Step 6. Plug your washing machine’s power cord into the outlet and turn the water supply on. Try running a wash cycle to see if the problem has been fixed.
3. Damaged Water Inlet Valve
Here’s what you’ll need to do to replace a damaged water inlet valve in your Amana washing machine…
How To Replace Damaged Water Inlet Valve In Amana Top Loader Washing Machine
Do the following to replace a damaged water inlet valve in your Amana top loader washing machine…
Step 1. Before starting this repair, ensure that you shut the water supply valve and unplug the power cord from the outlet in order to prevent any chances of electrocution and water leakage.
Step 2. With a pair of pliers, unscrew the two water supply hoses from the ports at the back of your washing machine (ensure that you keep a rag nearby to clean up any water leaks).
Step 3. Insert a tool such as a putty knife under your washing machine’s control panel to release the two retaining clips. Lift the control panel off the base and lay it on the lid of your machine.
Step 4. Disconnect the water inlet valve electrical connector from the control board. With a Philips screwdriver, loosen the screws securing the inlet valve assembly to the back of the cabinet.
Step 5. Pull the water inlet valve assembly out of your washing machine and set it aside. Remove your new washing machine water inlet valve from its packaging.
Step 6. Mount the new water inlet valve on the cabinet and apply the screws with your Philips screwdriver. Connect the electrical connector of the new valve to the control board.
Step 7. Lift the control panel and snap it back into place. Connect the two inlet hoses to the ports at the back of your washing machine (ensure that they are properly secured).
Step 8. Plug your washing machine back into the power supply and turn the water supply valve back on. Test the washing machine by running a wash cycle.
How To Replace Damaged Water Inlet Valve In Amana Front Loader Washing Machine
Do the following to replace a faulty water inlet valve in your Amana washing machine…
Step 1. Before starting this repair, we recommend shutting your washing machine’s power supply and unplugging the power cord from the outlet before starting this repair in order to prevent electrocution and water leakage.
Step 2. Using a pair of pliers, unscrew the two inlet hoses attached to the back of your washing machine (make sure to spread a towel on the floor underneath the hoses to catch any water leaks).
Step 3. With a 1/4 inch nut-driver, take out the screws at the back of your washing machine securing the top panel. Slide the panel backwards about an inch or so, and lift it off the washing machine.
Step 4. Disconnect the electrical connectors attached to the inlet valve assembly (ensure that you note where each connector goes).
Step 5. Pull off the hoses attached to the inlet valve assembly (some water will leak, so keep a rag nearby).
Step 6. Use a screwdriver to loosen the screws at the back of the machine holding the water inlet valve. Pull the inlet valve assembly out of the cabinet and set it aside.
Step 7. Remove your new washing machine water inlet valve from its packaging. Install the new valve in the cabinet and use your screwdriver to apply the mounting screws at the back.
Step 8. Connect each hose to its appropriate port on the inlet valve. Connect the two electrical connectors to the terminals on the new valve.
Step 9. Slide the top panel onto the cabinet and apply the bolts at the back with your nut-driver.
Step 10. Reconnect the HOT and COLD water supply lines to the ports at the back of your washing machine (make sure the hoses are secured properly so water can’t leak out).
Step 11. Plug your washing machine back into the power supply and turn the water supply valve back on. Test the washing machine by running a wash cycle.
4. Damaged Water Level Sensor
The water level sensor in your washer monitors the water level and tells the inlet valve when to stop filling. If this part gets damaged, your washing machine may overfill or not fill at all. Here’s how to replace a failed water level sensor in your Amana washing machine…
How To Replace Damaged Water Level Sensor In Amana Front Loader Washing Machine
Do the following to replace the water level sensor in your front loader Amana washing machine…
Step 1. Unplug your washing machine’s power cord from the outlet before starting this repair in order to prevent electrocution.
Step 2. With a 1/4 inch nut-driver, take out the screws at the back of the machine securing the top panel. Pull the panel backwards and lift it off the machine.
Step 3. The water level sensor will be mounted at the side of the cabinet. Disconnect the electrical connector attached to the sensor.
Step 4. Rotate the switch and pull it off the cabinet. Pull the air pressure tube off the water level sensor.
Step 5. Take you new washing machine water level sensor out of its packaging. Connect the air pressure tube to the new sensor.
Step 6. Snap the new sensor into the cabinet and rotate it to secure. Connect the electrical connector to the new sensor.
Step 7. Slide your washing machine’s top panel back on and use your nut-driver to apply the screws at the back. Plug the power cord into the outlet and try running a wash cycle to make sure everything works properly.
Check out these other articles…
Washing Machine Will Not Agitate [Problems Solved]
Admiral Washing Machine Cycles [Issues & Solutions]
Washing Machine Timer [Issues & Solutions]
Admiral Washing machine Spin [Issues & Solutions]
Admiral Washing Machine Won’t Agitate [How To Fix]
How To Replace Belt On Admiral Washing Machine [Detailed Guide]
How To Replace Damaged Water Level Sensor In Amana Top Loader Washing Machine
Here are the steps you’ll need to take to replace a damaged water level sensor in your Amana top loader washing machine…
Step 1. Turn off your washing machine’s power supply before starting this repair in order to avoid electrocution.
Step 2. Using some wire or string, pull the pressure switch knob off the control panel and set it aside. Insert a tool such as a putty knife under your washing machine’s control panel to release the two retaining clips.
Step 3. Detach the control panel from the housing and lay it on the lid. Disconnect the wire harness attached to the water level sensor.
Step 4. Release the clamp on the hose attached to the pressure sensor using a pair of needle-nosed pliers. Pull the tube off the pressure sensor.
Step 5. Release the water level sensor from the mounting bracket using a flat-blade screwdriver. Pull the sensor off the panel and set it aside.
Step 6. Take your new washing machine water level sensor out of its packaging. Snap the new sensor into the opening on the mounting bracket.
Step 7. Connect the electrical connector to the new water level sensor. Attach the air pressure tube to the port on the new level sensor and secure it with the retaining clamp.
Step 8. Lift the control panel assembly and snap it back into the housing. Plug your washer back into the power outlet and try running a wash cycle to see if the problem has been fixed.
5. Damaged Control Board
If your washing machine isn’t filling, the fault could lie with the control board; however, you need to keep in mind that this isn’t a very common issue. Here’s what you’ll need to do to replace a damaged control board in your Amana washing machine…
How To Replace Control Board In Amana Front Loader Washing Machine
Do the following to replace a damaged control board in your Amana front loader washing machine…
Step 1. Make sure to unplug your machine from the power outlet before starting this repair in order to prevent any chances of electrocution.
Step 2. Use a 1/4 inch nut-driver to remove the screws at the back of the machine securing the top panel. Slide the panel backwards about an inch or so, and lift it off the machine.
Step 3. Detach the control board from the side of the cabinet using a flat-blade screwdriver. Pull the cover off the board and disconnect all the electrical connectors attached to it (make sure to note where each connector goes).
Step 4. Release the wires from the retainers and set the control board aside. Take your new washing machine control board out of its packaging.
Step 5. Connect each electrical connector to its appropriate terminal on the new control board. Mount the new board on the cabinet and snap it into place.
Step 6. Put the cover onto the new control board. Slide the top panel onto your washing machine and use your nut-driver to apply the screws at the back.
Step 7. Plug your washing machine back into the power outlet and try running a wash cycle to make sure the problem has been fixed.
How To Replace Control Board In Amana Top Loader Washing Machine
Here are the steps you’ll need to take to replace a damaged control board in your Amana top loader washing machine…
Step 1. In order to prevent any chances of electrocution, make sure to unplug your washing machine from its power supply before starting this repair.
Step 2. Insert a tool such as a putty knife under the control panel to release the two spring clips. Detach the control panel from the base and lay it on the lid of your washing machine.
Step 3. Disconnect all the wire harnesses attached to the control board (ensure that you take note of where each connector goes). Release the wires from the retainers and pull the air pressure tube off the board.
Step 4. Using a 1/4 inch nut-driver, remove the bolts securing the control board to the control panel. Lift the board off the panel and set it aside.
Step 5. Remove your new washing machine control board from its packaging. Use a pair of pliers to pry the wire retainer off the old control board and transfer it to the new one.
Step 6. Mount the new control board on the control panel and apply the screws with your 1/4 inch nut-driver.
Step 7. Connect each wire harness to its appropriate terminal on the new control board and secure the wires in the retainer. Connect the air pressure tube to the port on the new board.
Step 8. Lift the control panel assembly and snap the selector knob onto the new shaft. Snap the control panel assembly into the cabinet.
Step 9. Plug your washing machine back into the power supply and make sure the problem has been fixed by running a wash cycle.
