If your GE washing machine stops due to various reasons and you don’t know what to do, you’ve come to the right place. Follow the instructions in this detailed guide to resolve this issue…
GE Washing Machine Won’t Stop Filling With Water — How To Fix
If your GE washing machine keeps filling with water, there are two things that could cause this problem; the water inlet valve and the water pressure switch. To find out which part is defective, do the following…
Step 1. Turn on the water and power supply of your washing machine and run a normal wash cycle.
Step 2. Pay attention to the washing machine during the fill stage. Once it starts to overfill, turn off the power supply. If the washer stops filling, the fault lies with the water pressure switch.
However, if the washing machine keeps filling even when the power is turned off, the water inlet valve is defective. Do the following to replace both parts…
Replacing A GE Front Loader Washing Machine Water Inlet Valve
To replace a defective water inlet valve in your GE front loader washing machine, do the following…
Step 1. Make sure to turn off your washing machine’s water and power supply before attempting any repairs in order to avoid water leakage and electrocution.
Step 2. Go to the back of your washing machine and disconnect the water inlet hoses (keep a rag nearby in case of water spillage).
Step 3. Remove the screws at the back of your washing machine holding the top panel with a Philips screwdriver.
Step 4. Slide the top panel back about an inch or so and lift it off your washing machine.
Step 5. Disconnect the solenoid wires connected to the water inlet valve inside the washing machine’s cabinet (ensure that you take note of the positioning of each wire).
Step 6. Use a pair of pliers to press the clamp holding the hose to the water inlet valve and slide it out of place.
Step 7. Disconnect the hose from the water inlet valve assembly.
Step 8. Take out the two mounting screws at the back of your washing machine holding the water inlet valve with a Philips screwdriver.
Step 9. Pull the water inlet valve assembly out of the washing machine.
Step 10. Get your new water inlet valve assembly out of its pack.
Step 11. Install the new water inlet valve in your washing machine and secure it by applying the two Philips screws at the back of the washing machine.
Step 12. Connect the hose to the new water inlet valve assembly and slide the retaining clamp in place to secure it.
Step 13. Connect each solenoid wire to its appropriate terminal on the new water inlet valve assembly.
Step 14. Connect each of the water inlet hoses to their appropriate ports on the new water inlet valve assembly (in order to prevent water leakage, ensure that the connection is properly secured).
Step 15. Slide the top panel of your washing machine back on and apply the Philips screws at the back to secure it.
Step 16. Turn on your washing machine’s water and power supply.
Step 17. Try running a wash cycle to ensure that everything is working properly.
How To Replace A GE Front Loader Washing Machine Water Pressure Switch
Here’s how to replace a defective water pressure switch in your GE front loader washing machine…
Step 1. Make sure to turn off your washing machine’s water and power supply before attempting any repairs in order to avoid water leakage and electrocution.
Step 2. Take out the screws at the back of your washing machine holding the top panel with a screwdriver.
Step 3. Slide the panel back a few inches and lift it off your washing machine.
Step 4. The water pressure switch is mounted on the left side of the cabinet frame. Disconnect the two electrical connectors attached to the switch.
Step 5. Turn the water pressure switch slightly and detach it from the washing machine’s cabinet.
Step 6. Press the clamp on the hose connected to the water pressure switch and slide it out of place.
Step 7. Disconnect the hose from the water pressure switch and take the switch out of your washing machine.
Step 8. Get your new water pressure switch out of its pack and connect it to the hose.
Step 9. Secure the hose to the water pressure switch by sliding the retaining clamp in place.
Step 10. Snap the new water pressure switch in place on the washing machine’s cabinet.
Step 11. Connect the two electrical connectors to their appropriate terminals on the new water pressure switch.
Step 12. Slide the top panel of your washing machine back on and secure it by applying the screws at the back.
Step 13. Turn on your washing machine’s water and power supply.
Step 14. Run a wash cycle to ensure that everything is working properly.
How To Replace GE Top Loader Washing Machine Water Inlet Valve
Do the following to replace the water inlet valve on your GE top loader washing machine…
Step 1. Before attempting any repairs, make sure to turn off your washing machine’s water and power supply in order to avoid water leakage and electrocution.
Step 2. Go to the back of your washing machine and disconnect the water inlet hoses (get ready for some water to spill out).
Step 3. Take out the screws at the back of the control panel.
Step 4. Slide the control panel sideways and detach it from your washing machine.
Step 5. The water inlet valve will be mounted on the control panel bracket. Disconnect the solenoid wires from the valve.
Step 6. Use a pair of pliers to press the clamp on the hose connected to the water inlet valve and slide it out of place.
Step 7. Use your screwdriver to take out the mounting screws holding the water inlet valve assembly to your washing machine.
Step 8. Pull the water inlet valve assembly out of your washing machine.
Step 9. Get your new water inlet valve out of its pack.
Step 10. Install the new water inlet valve in your washing machine and apply the three mounting screws to secure it.
Step 11. Connect the hose to the new water inlet valve and secure it by sliding the retaining clamp in place.
Step 12. Connect the each solenoid wire to its appropriate terminal on the new water inlet valve.
Step 13. Put the control panel back on and secure it by applying the screws at the back.
Step 14. Connect the water inlet hoses to the ports at the back of your washing machine.
Step 15. Turn on your washing machine’s water and power supply.
Step 16. Run a wash cycle to make sure everything is working properly.
Note: Click here to learn more about your washing machine’s water inlet valve.
How To Replace A GE Top Loader Washing Machine Water Pressure Switch
Do the following to replace the water pressure pressure switch on your GE top loader washing machine…
Step 1. Turn off your washing machine’s water and power supply before attempting any repairs in order to avoid water leakage and electrocution.
Step 2. Disconnect the water inlet hoses from the back of your washing machine.
Step 3. Use your screwdriver to take out the screws at the back of the control panel and disconnect wires connected to it.
Step 4. Wedge a putty knife under the main top panel of your washing machine to release the clips holding the main front panel of your washing machine.
Step 5. Detach the panel from the washing machine and set it aside.
Step 6. Use your Philips screwdriver to take out the two screws holding the main top panel of your washing machine.
Step 7. Pull the main top panel forward slightly and lift it up.
Step 8. Use a pair of pliers to squeeze and release the wire retainer from the frame.
Step 9. Open the lid of your washing machine and squeeze the tab on the lid switch to release it.
Step 10. Turn the lid switch sideways and push it through the opening.
Step 11. Lift the main top panel off the washing machine and set it aside.
Step 12. Use your screwdriver to take out the screws holding the control panel bracket, rear panel, and trim.
Step 13. Use a pair of pliers to detach the tube connected top the water pressure switch.
Step 14. Use a pair of pliers to squeeze the water pressure switch tab under the control panel bracket to release the switch.
Step 15. Disconnect the electrical connectors from the water pressure switch.
Step 16. Get your new water pressure switch out of its pack.
Step 17. Snap the new water pressure switch into the control panel bracket.
Step 18. Connect the wires to the new water pressure switch.
Step 19. Connect the air pressure tube to the new water pressure switch.
Step 20. Put the control panel trim back in place and apply the screws to secure.
Step 21. Secure the rear panel to the trim by applying the screws.
Step 22. Apply the screws on the control panel bracket.
Step 23. Insert the lid switch through the hole in the main top panel and snap it back in place.
Step 24. Snap the lid switch wire retainer into the frame.
Step 25. Slide the main top panel back in place and apply the screws at the front to secure it.
Step 26. Snap the main front panel of your washing machine back in place.
Step 27. Reconnect the wire connectors to the control panel and snap the panel back in place. Apply the screws at the back to secure it.
Step 28. Connect the water inlet hoses back to the washing machine.
Step 29. Turn on your washing machine’s water and power supply.
Step 30. Run a wash cycle to ensure that everything is working properly.
Check out these other articles…
GE Washing Machine Error [Codes, Meaning & Solutions]
GE Washing Machine Button [Issues & Solutions]
How To Reset GE Washing Machine [Detailed Guide]
GE Washing Machine Won’t Stop [Issues & Solutions]
Lock/Unlock GE Washing Machine [How To/Issues & Solutions]
GE Washing Machine Stops At Rinse Cycle — Solution
If your GE washing machine stops at the rinse cycle, it means that something is preventing the washer from draining. Here are the things that could cause this issue…
1.Blocked Drain Pump Filter (Front Loader Washing Machines Only)
Here’s how to clean a clogged drain pump filter in your GE front loader washing machine…
Step 1. Before attempting any repairs, ensure that you turn off your washing machine’s water and power supply in order to avoid water leakage and electrocution.
Step 2. Using a flat-blade screwdriver, pry out the little panel at the lower front section of your washing machine. Pull out the drain channel under the panel
Step 3. Place a container under the drain channel to catch any water that is stuck in the washing machine.
Step 4. To control the quantity of water being released, turn the knob inside the drain channel counter-clockwise slowly and pull it out (this is the drain pump filter).
Step 5. Once all the water has drained out from your washing machine, take the drain pump filter to a sink and clean out any lint or debris that may have accumulated in it.
Step 6. Once you’ve cleaned the filter properly, put it back in place and turn it clockwise to secure.
Step 7. Flip the drain channel up and push the access panel back in place.
Step 8. Turn on your washing machine’s water and power supply.
Step 9. Run a wash cycle to ensure that everything is working properly.
2.Defective Drain Pump
Here’s how to replace a defective drain pump in your GE washing machine…
How To Replace A GE Top Loader Washing Machine Drain Pump
To replace the drain pump on your GE top loader washing machine, do the following…
Step 1. Before attempting any repairs, ensure that you turn off your washing machine’s water and power supply in order to avoid water leakage and electrocution.
Step 2. Insert a putty knife under the main top panel of your washing machine to release the two clips holding the main front section of your washing machine.
Step 3. Detach the panel from the washing machine and set it aside.
Step 4. Disconnect the electrical connector from the drain pump.
Step 5. Use a pair of pliers to press the clamps on the tub-to-pump and outlet hose and slide the clamps out of place.
Step 6. Disconnect the two hose from the drain pump assembly.
Step 7. Take out the mounting nut holding the drain pump assembly to the base of your washing machine.
Step 8. Pull the drain pump assembly out of the washing machine’s cabinet.
Step 9. Get your new drain pump assembly out of its pack.
Step 10. Install the drain pump assembly in your washing machine and secure it to the base of the washer by applying the mounting nuts.
Step 11. Connect the tub-to-pump and outlet hoses to their appropriate port on the new drain pump assembly and secure them by sliding the retaining clamps in place.
Step 12. Connect the electrical connector to the new drain pump assembly.
Step 13. Snap the main front panel of your washing machine back in place.
Step 14. Turn on your washing machine’s water and power supply.
Step 15. Run a wash cycle to ensure that everything is working properly.
How To Replace A GE Front Loader Washing Machine Drain Pump
To replace the drain pump in your GE front loader washing machine, do the following…
Step 1. Before attempting any repairs, make sure you turn off your washing machine’s water and power supply in order to avoid water leakage and electrocution.
Step 2. Take out the three screws holding the lower front panel of your washing machine with a Philips screwdriver.
Step 3. Pull the panel out of the washing machine.
Step 4. Place a towel under the hoses connected to the drain pump to catch any water leaks.
Step 5. Use a pair of pliers to press the clamps holding the two hoses to the drain pump assembly and slide them out of place.
Step 6. Detach the tub-to-pump hose and the outlet hose from the drain pump assembly.
Step 7. Reach inside the washing machine and disconnect the two electrical connectors attached to the drain pump assembly.
Step 8. Use your Philips screwdriver to take out the screws holding the drain pump assembly to the washing machine.
Step 9. Lift the drain pump out of your washing machine.
Step 10. Get your new drain pump assembly out of its pack.
Step 11. Install the new drain pump assembly inside your washing machine and apply the two Philips mounting screws to secure it to the base.
Step 12. Connect the two electrical connectors to their appropriate terminals on the new drain pump assembly.
Step 13. Connect the tub-to-pump and outlet hoses to their appropriate ports on the new drain pump assembly. Secure the hoses by sliding the retaining clamps in place.
Step 14. Put the lower front panel of your washing machine back on and apply three screws at the bottom to secure it.
Step 15. Turn on your washing machine’s water and power supply.
Step 16. Run a wash cycle to ensure that everything is working properly.
GE Washing Machine Stops Spinning — Solved
Here are the things that could cause your GE washing machine to stop spinning…
1.Unbalanced Load
Do the following to fix an unbalanced load in your GE washing machine…
Step 1. Turn off your washing machine’s power supply.
Step 2. Open the door of your washing machine and inspect the quantity of clothes in the drum. Ensure that the drum has not been filled past 3/4. If the drum is overloaded, your washing machine won’t be able to spin properly.
Step 3. Ensure that your washing machine sits on a firm, even surface. If your washing machine is tilted at an angle, the weight of the clothes won’t be spread evenly.
Step 4. Turn on your washing machine’s power supply and try running the spin cycle again to see if the issue has been resolved.
2.Worn Tub Bearings
Do the following to replace the tub bearings on your GE washing machine…
Step 1. Before attempting any repairs, make sure to turn off your washing machine’s water and power supply in order to avoid water leakage and electrocution.
Step 2. Disconnect the water inlet hoses from the back of your washing machine.
Step 3. Use a screwdriver to take out the screws at the back of the control panel.
Step 4. Slide the control panel sideways a bit to detach it from the main top of the washer.
Step 5. Detach the wires from the control panel and set it aside.
Step 6. Insert a putty knife under the main top panel of your washing machine to release the clips holding the front section of your washing machine.
Step 7. Pull the front panel off your washing machine and set it aside.
Step 8. Use your screwdriver to take out the two screws at the front of your washing machine holding the main top panel.
Step 9. Slide the panel forward a bit and lift it up slightly.
Step 10. Reach under the top panel and use a pair of pliers to release the lid switch wire retainer from the cabinet.
Step 11. Open the lid of your washing machine.
Step 12. Reach under the tab and squeeze the tab on the lid switch to release it.
Step 13. Push the lid switch through the opening at the top. Turn the lid switch sideways and push it back through the opening.
Step 14. Take the main top panel off the washing machine completely.
Step 15. Use your screwdriver to take out the screws on the control panel bracket, trim, and rear panel.
Step 16. Use a pair of pliers to release the air pressure tube from the water pressure switch.
Step 17. Set the control panel bracket aside.
Step 18. Use your screwdriver to take out the screws holding the shock dampening straps to the tub cover and pull the straps off.
Step 19. Release the tabs at the bottom of the tub cover and pull the cover off the tub.
Step 20. Pull up the dispenser cap and rotate the cup counter-clockwise to take it out of the washer’s tub.
Step 22. Take out the agitator bolt using a 7/16 inch socket wrench (turn clockwise to take it out).
Step 23. Pull the agitator out of the washing machine.
Step 24. Pull the drive block and washer off the agitator shaft.
Step 25. Take out the tub nut using a 1-11/16 inch tub nut wrench (turn clockwise).
Step 26. Lift the inner tub off the drive shaft and set it aside.
Step 27. Using a flat-blade screwdriver, pry the split ring off the drive shaft and lift the washer nut out.
Step 28. Disconnect the mode shifter and motor wires from the drive motor (take note of the positioning of each wire).
Step 29. Use a screwdriver to take out the drive motor grounding wire.
Step 30. Use a pair of pliers to release the wires from the drive motor mounting bracket.
Step 31. Untwist the wires from the suspension rod.
Step 32. Use your screwdriver to release the screw holding the drain hose to the tub of your washing machine.
Step 33. Pull the hose off the tub (expect some water to leak out.
Step 34. Use a pair of pliers to disconnect the air pressure tub from the side of the tub and detach it from the retainer.
Step 35. Lift the tub up slightly and release the four suspension rods from the base frame.
Step 36. Tilt the tub and motor assembly forward a bit and pull it out of the cabinet.
Step 37. Lay the tub on the ground and turn it upside down.
Step 38. Release the drive belt from the bottom of the tub.
Step 39. Take out the nut holding the drive pulley with a 3/4 socket wrench.
Step 40. Lift the pulley off and take out the hex bolts underneath.
Step 41. Use your socket wrench to take out the bolts holding the base frame to the outer tub.
Step 42. Cut the zip-tie holding the overflow tube to the base frame.
Step 43. Lift the base frame assembly off the outer tub.
Step 44. Pull the mode shifter and shaft assembly out of the tub.
Step 45. Pull the nylon washer off and use a screwdriver to take out the screw holding the tub bearing.
Step 46. Pry the bearing out of the tub.
Step 47. Get your new tub bearing out of its pack.
Step 48. Push the new tub bearing into the opening at the bottom of the tub.
Step 49. Apply the screw to secure the new tub bearing to the outer tub.
Step 50. Put the nylon washer on the new tub bearing.
Step 51. Insert the shaft and mode shifter assembly through the opening at the bottom of the tub.
Step 52. Align the base frame with the mode shifter and outer tub.
Step 53. Use your socket wrench to reapply the base frame bolts.
Step 54. Use a zip-tie to secure the overflow tube to the base frame.
Step 55. Secure the mode shifter by applying the hex bolts.
Step 56. Put the drive pulley back on and reapply the nut with a socket wrench to secure it.
Step 55. Loop the drive belt back around the motor shaft and drive pulley.
Step 56. Put the tub and motor assembly back inside the cabinet (ensure that the motor is facing forward.
Step 57. Lift the outer tub up a bit and snap the four suspension rods back in place on the base frame.
Step 58. Reconnect the air pressure tube to the side of the tub and secure the tube to the suspension rod with the retaining wire.
Step 59. Connect the drain hose back to the bottom of the tub and reapply the screw to secure it.
Step 60. Wind the motor wires around the suspension rod and snap all the retainers in place.
Step 61. Reapply the screw to secure the grounding wire.
Step 62. Connect the mode shifter and motor wires to the drive motor.
Step 63. Put the washer nut and split ring back on the drive shaft.
Step 64. Put the inner tub back in place by aligning it on the drive shaft.
Step 65. Put the tub nut back in place and thread it counter-clockwise to secure it.
Step 66. Put the washer and drive block back in place on the agitator shaft.
Step 67. Put the agitator back in place and apply the bolt to secure it.
Step 68. Put the soap dispenser cup back in place and turn it clockwise to secure it.
Step 69. Snap the tub cover back in place.
Step 70. Connect the shock dampening straps back to the tub cover and secure them by applying the screws.
Step 71. Put the control panel bracket back in place and apply the screws to secure it.
Step 72. Reconnect the air pressure tube to the water pressure switch.
Step 73. Put the control panel trim and rear panel back in place. Apply the screws to secure.
Step 74. Insert the lid switch through the hole in the main top panel and snap the switch in place.
Step 75. Snap the wire retainer into the frame.
Step 76. Push the main top panel back in position and apply the screws at the front to secure it.
Step 77. Snap the main front panel of your washing machine back in place.
Step 78. Reconnect the electrical connectors to the control board and push the board back in place. Apply the screws at the back to secure.
Step 79. Connect the water inlet hoses back to your washing machine.
Step 80. Turn on your washing machine’s water and power supply to ensure that everything is working properly.
Note: Please keep in mind that the procedure above is for top loader washing machines only.
