If you have any trouble with your Kenmore washing machine door, you’ve come to the right place. This detailed guide explains the causes of theses issues and provides easy-to-follow steps to fix them…
Table of Contents
How To Replace Kenmore Washing Machine Door Glass — Solved
To replace your front loader Kenmore washing machine door glass, follow the steps below…
Step 1. Disconnect your washing machine’s power cord from the outlet before starting this repair in order to prevent any chances of electrocution.
Step 2. Open your washing machine’s door. Using a Philips screwdriver, loosen the bolts holding the door hinge to the front panel carefully lift the door assembly off the machine.
Step 3. Set the door assembly on a flat surface. Use your screwdriver to take out the bolts holding the two door frames together. Pry the inner door frame off the assembly, then set it aside.
Step 4. Lift the old door glass off the outer frame, then discard it. Prepare the new door glass for installation by unpacking it.
Step 5. Place the new door glass on the outer frame. Lower the inner door frame onto the glass, then secure the two frames by applying the Philips screws.
Step 6. Carefully lift the door assembly, then mount the hinges on the front panel. Secure the door hinges by applying the Philips screws. Close your washer’s door, then plug the power cord back into the outlet.
How To Replace Kenmore Washing Machine Door Hinge — Quick Fix
To replace the door hinge in your front loader Kenmore washing machine, follow the steps below…
Step 1. In order to prevent any chances of electrocution, it is advised that you disconnect your washing machine’s power cord from the outlet before starting this repair.
Step 2. Open the door of your washing machine. Using a flat-blade screwdriver or a pair of needle-nosed pliers, carefully pry the retaining band off the door boot seal (be careful not to puncture the seal).
Step 3. Peel the door gasket off the front panel. Reach into the cabinet behind the front panel, then disconnect the wire harness from the door lock.
Step 4. Open the lower front access panel, then pull the emergency drain tube out of the retainers. Loosen the screws holding the pump filter housing. Pull the housing out of the cabinet, then set it aside.
Step 5. Use your Philips screwdriver to take out the bolt at the bottom of the front panel. Go to the back of the machine, then loosen the nuts securing the top panel.
Step 6. Pull the top panel backwards a few inches, then lift it off the machine. Pull the detergent tray out of the dispenser. Press the little tab inside the tray to release it from the housing.
Step 7. Use your Philips screwdriver to loosen the bolts at the back of the control panel. Pry the panel off the mounting bracket, then set it on top of the cabinet.
Step 8. Using your screwdriver, take out the bolts at the top of the front panel. Carefully lift the front panel off the cabinet and set it aside.
Step 9. Set the front panel on a flat surface, then open the door. Using your Philips screwdriver, take out the bolts holding the door hinge cover. Pry the cover off and set it aside.
Step 10. Take out the screws holding the door hinge pin bushings. Detach the door assembly from the hinges. Take the bushings off the hinge.
Step 11. Set the front panel on its back. Loosen the screws securing the door hinge to the front panel. Take the hinges off, then discard them.
Step 12. Prepare the new hinges for installation by unpacking them. Mount the new hinges on the front panel, then tighten the screws to secure it.
Step 13. Place the bushings on the hinge pins. Align the hinge to the door assembly, then use your Philips screwdriver to apply the bolts.
Step 14. Snap the hinge cover onto the door assembly, then apply the screws. Lift the front panel, then remount it on the cabinet. Use your Philips screwdriver to tighten the screws at the top of the front panel.
Step 15. Apply the single screw at the bottom of the front panel. Push the pump filter housing into the cabinet, then use your Philips screwdriver to apply the nuts.
Step 16. Open the door of the machine. Reach into the cabinet behind the front panel, then plug the wire harness into the door lock.
Step 17. Fit the door boot seal around the front panel. Use your needle-nosed pliers to fit the retaining wire around the door boot seal.
Step 18. Plug the wire harness into the control panel. Snap the panel onto the front of the cabinet, then apply the screws at the back using a Philips screwdriver.
Step 19. Push the soap tray into the dispenser. Mount the top panel on the cabinet, then push it forwards. Apply the nuts at the back of the panel. Plug your washing machine back into the outlet.
Check out these other articles…
Kenmore Washing Machine Is Not Spinning [7 Solutions]
KitchenAid Washing Machine Is Not Draining [2 Problems & Proven Solutions]
KitchenAid Washing Machine Motor [2 Issues & Proven Solutions]
KitchenAid Washing Machine Water Inlet Valve [2 Issues & Proven Solutions]
KitchenAid Washing Machine Is Leaking [4 Causes & Proven Solutions]
KitchenAid Washing Machine Is Not Spinning [12 Causes & Proven Solutions]
KitchenAid Washing Machine Door [6 Issues & Proven Solutions]
How To Replace Kenmore Washing Machine Door Seal — Detailed Steps
To replace your Kenmore washing machine door seal, follow the steps below…
Front Loaders
Do the following to replace the door seal in your front loader Kenmore washing machine…
Step 1. Ensure that your machine is disconnected from the outlet and the water taps are off before starting this repair in order to prevent any chance of electrocution or leakage.
Step 2. Open your washer’s door, then loosen the bolts securing the door lock to the front panel using a Philips screwdriver.
Step 3. Using needle-nosed pliers or a flat-blade screwdriver, pry the retaining wire off the door boot seal carefully. Peel the door seal off the front panel.
Step 4. Reach into the cabinet behind the front panel, then disconnect the wire harness from the door lock assembly.
Step 5. Pry the pump filter access panel open, then pull the emergency drain tube out of the retainers.
Step 6. Take out the screws securing the pump filter housing. Pull the housing out of the cabinet, then set it aside.
Step 7. Take out the single screw at the bottom of the front panel. Go to the back of the washer, then use your Philips screwdriver to take out the bolts securing the top panel.
Step 8. Slide the top panel backwards a few inches, then lift it off the machine. Slide the soap tray out of the dispenser. Release the tray from the housing by pressing the little tab inside.
Step 9. Take out the two screws next to the dispenser opening. Use your Philips screwdriver to take out the bolts at the back of the control panel.
Step 10. Pry the control panel off the mounting bracket, then set it on top of the cabinet. Loosen the screws at the top of the front panel.
Step 11. Lift the panel off the cabinet, then set it aside. Using pliers, release the retaining clamps holding the tubes to the door boot seal. Detach the tubes from the door seal.
Step 12. Using a flat-blade screwdriver or a spring expansion tool, carefully pry the inner retaining band off the door boot seal. Pry the seal off the drum opening.
Step 13. Prepare the new door boot seal for installation by unpacking it. Transfer the nozzle from the old door seal to the new one.
Step 14. Carefully fit the new door seal around the drum opening. Using needle-nosed pliers or a flat-blade screwdriver, fit the inner retaining wire around the new door seal.
Step 15. Connect the tubes to the ports on the door boot seal, then slide the retaining clamps into place.
Step 16. Carefully lift the front panel and mount it on the cabinet. With your Philips screwdriver, tighten the bolts at the top of the front panel.
Step 17. Apply the single screw at the bottom of the front panel. Push the pump filter housing into the cabinet, then tighten the two screws.
Step 18. Plug each wire harness into the control panel. Snap the panel onto the cabinet, then use your Philips screwdriver to apply the bolts at the back.
Step 19. Push the soap tray into the dispenser. Place the top panel on the cabinet, then secure it by tightening the screws at the back.
Step 20. Open your washer’s door. Reach behind the front panel, then reconnect the wire harness to the door lock assembly.
Step 21. Fit the new door gasket around the door opening. Use your flat-blade screwdriver to fit the outer retaining wire around the seal. Plug your washing machine’s power cord into the outlet, then turn the water taps on.
Dryers
To replace the door seal in your Kenmore dryer, follow the steps below…
Step 1. Ensure that you disconnect your machine from the outlet before starting this repair in order to prevent electrocution.
Step 2. Open the door of your dryer, then use a Philips screwdriver to loosen the bolts securing the hinge. Lift the door assembly off the front panel.
Step 3. Using your Philips screwdriver, take out the bolts holding the inner frame to the door assembly. Lift the inner frame off the door, then peel the rubber seal off.
Step 4. Prepare your new door seal for installation by unpacking it. Carefully fit the new seal around the inner door frame.
Step 5. Mount the inner frame on the door assembly, then apply the screws with your Philips screwdriver.
Step 6. Mount the door assembly on the front panel. Using your Philips screwdriver, tighten the bolts on the hinge. Plug your washing machine back into the outlet.
Kenmore Washing Machine Door Won’t Lock — Solution
If your Kenmore washing machine door won’t lock, it indicates that the door switch is damaged. Follow the steps below to replace this part…
Front Loaders
Take the following steps to replace the door lock assembly in your front loader Kenmore washing machine…
Step 1. In order to prevent any chances of electrocution, disconnect your appliance from the power outlet before starting this repair.
Step 2. Open your washing machine’s door. Wedge a flat-blade screwdriver underneath the retaining band around the door seal. Work the screwdriver around until the wire pops off.
Step 3. Peel the door boot seal off the front panel. Reach behind the front panel, then disconnect the wire harness from the door lock assembly.
Step 4. Using your Philips screwdriver, loosen the bolts holding the door lock to the front panel. Pull the lock assembly out of the cabinet, then discard it.
Step 5. Prepare your new washing machine door lock for installation by unpacking it. Install the new door lock in the cabinet, then tighten the bolts using your Philips screwdriver.
Step 6. Plug the wire harness into the door lock assembly. Refit the door boot seal around the door opening. Using a flat-blade screwdriver, fit the retaining wire around the seal.
Step 7. Plug your washing machine’s power cord back into the electrical outlet. To ensure that the issue has been fixed, try running a wash cycle.
Top Loaders
Take the following steps to replace the lid lock in your top loader Kenmore washing machine…
Step 1. Ensure that you disconnect your machine from the outlet before starting this repair in order to prevent any chances of electrocution.
Step 2. Using your Philips screwdriver, loosen the bolts securing the rear cover to the control panel. Pry the cover off the panel and set it aside.
Step 3. Lift the control panel off the base, then set it face-down on the cabinet. Use your screwdriver to take out the nuts holding the cover to the control board.
Step 4. Disconnect the lid switch wire harness from the control board. Lift the control panel and snap it back into the base.
Step 5. Insert a putty knife underneath the top panel (this will help release the locking clips). Carefully lift the top panel and support it.
Step 6. Loosen the bolts holding the lid switch to the bottom of the top panel. Release the lid switch wire from the retainers on the panel.
Step 7. Pull the lid switch assembly out of the cabinet, then discard it. Prepare the new lid switch for installation by unpacking it.
Step 8. Mount the new lid switch at the bottom of the top panel, then tighten the screws to secure it.
Step 9. Secure the lid switch wire in the retainers underneath the top panel. Pass the lid switch connector through the opening on the top panel.
Step 10. Lower the top panel and snap it onto the cabinet. Detach the control panel from the base, then set it face-down on the cabinet.
Step 11. Plug the lid switch wire harness into the control board. Snap the cover onto the control board, then tighten the screws to secure it.
Step 12. Lift the control panel assembly and snap it into the base. Place the rear cover on the control panel, then apply the bolts using your Philips screwdriver.
Step 13. Plug your washing machine’s power cord into the outlet, then try running a cycle to ensure that the issue has been fixed.
Dryers
Follow the steps below to replace the door lock assembly in your Kenmore dryer…
Step 1. Prevent any chances of electrocution by disconnecting your machine from the power outlet before starting this repair.
Step 2. Go to the back of the machine, then loosen the bolts securing the top panel using a Philips screwdriver. Slide the panel backwards, then lift it off the cabinet.
Step 3. Take out the screws at the back of the control panel. Using a flat-blade screwdriver if needed, pry the control panel off the mounting bracket.
Step 4. Set the control panel on top of the cabinet. Open the door of your machine. Press the tab on the door switch to release it from the front panel.
Step 5. Pull the door lock out of place, then disconnect the wire harness. Prepare the new door lock for installation by unpacking it.
Step 6. Plug the connector into the new door switch. Snap the new door lock into the front panel.
Step 7. Snap the control panel onto the front of the cabinet, then apply the screws at the back using a Philips screwdriver.
Step 8. Mount the top panel on the cabinet, then use your Philips screwdriver to apply the bolts.
Step 9. Plug your appliance back into the outlet, then ensure that the issue has been fixed by running a spin cycle.