Kenmore Washing Machine Error Codes [How To Fix]

If you are getting Kenmore washing machine error codes, you’ve come to the right place. In this guide, we’ll be explaining the causes of this issue and giving you steps on how to fix them…

Kenmore Washing Machine Error Code FE — Solved

The FE Kenmore washing machine error code indicates that the appliance is overfilling. The following are causes of this issue…

1. Failed Inlet Valve

If your Kenmore washing machine is overfilling, it is most likely as a result of a failed inlet valve. To test the valve assembly in your washing machine, follow the steps below…

Front Loaders

To test the inlet valve in your front loader Kenmore washing machine, take the following steps…

Step 1. In order to prevent electrocution and water leakage, it is advised that you disconnect your washing machine’s power cord from the outlet before starting this procedure.

Step 2. Using pliers if needed, disconnect the HOT and COLD water supply hoses to the ports at the back of the machine (some water may spill, so we recommend keeping a rag nearby).

Step 3. With a Philips screwdriver, take out the screws at the back of the machine holding the top panel. Pull the panel backwards about an inch or so, then lift it off the cabinet.

Step 4. Note the positioning of the connectors attached to the inlet hose, then disconnect each one.

Step 5. With your pliers, release the retaining clamps holding the inlet tubes to the valve assembly. Disconnect the hoses from the valve (keep a rag nearby).

Step 6. Loosen the screws holding the valve assembly to the cabinet using a Philips screwdriver. Pull the inlet valve out of a cabinet.

Step 7. Get a digital multimeter, then turn the dial to the lowest ohms of resistance setting. Place the multimeter’s probes on each of the inlet valve terminals. For a working valve, you should get a reading between 500 and 1600 ohms.

Step 8. If the reading is much lower or higher than these numbers, the valve is damaged and needs to be replaced. Once you are satisfied that the valve is in good condition, reinstall it in the cabinet, then apply the screws.

Step 9. Reconnect the inlet tubes to the ports on the valve, then slide the retaining clamps into place.

Step 10. Plug each wire connector into its appropriate terminal on the valve assembly. Mount the top panel on the cabinet, then tighten the bolts using your Philips screwdriver.

Step 11. Reconnect the COLD and HOT water supply hoses to the ports at the back of the machine (ensure that the hoses are properly attached in order to prevent leakage).

Step 12. Plug your washing machine’s power cord into the outlet, then turn the water supply taps on.

Top Loaders

To test the inlet valve in your top loader Kenmore washing machine, follow the steps below…

Step 1. Ensure that your washing machine’s water faucets are turned off and the power cord is disconnected from the outlet before starting this repair.

Step 2. Using a pair of pliers if needed, detach the water supply hoses from the ports at the back of the machine (it is advised that you keep a rag nearby to clean any leaks.

Step 3. Using a Philips screwdriver, take out the nuts holding the control panel’s rear cover. Pry the panel off the machine and set it aside.

Step 4. Lift the control panel off the base, then set it face-down on the cabinet. Note the positioning of the connectors attached to the valve assembly, then disconnect each one.

Step 5. Use your pliers to release the clamps holding the inlet tubes to the valve. Detach each tube from the valve.

Step 6. Loosen the screws holding the valve assembly to the cabinet using a Philips screwdriver. Pull the valve out of the cabinet.

Step 7. Get a digital multimeter, then turn the dial to the lowest setting for ohms of resistance.

Step 8. Place the probes of the meter on each of the valve’s terminals. For a working inlet valve, you should get a reading between 500 and 1600 ohms. If the reading is much lower or higher than these numbers, the valve will need to be replaced.

Step 9. Once you are satisfied that the valve is in good condition, remount it on the cabinet, then apply the bolts using a Philips screwdriver.

Step 10. Connect the inlet tubes to the ports on the inlet valve, then slide the retaining clamps into place to secure the connection.

Step 11. Plug each wire connector into the appropriate terminal on the valve assembly.

Step 12. Lift the control panel and snap it back into the base. Snap the rear cover onto the control panel, then tighten the screw with your Philips screwdriver.

Step 13. Plug your washing machine’s power cord back into the outlet, then turn the water supply taps back on.

2. Damaged Pressure Switch

The next thing that could cause this Kenmore washing machine error code is a faulty water pressure switch. Follow the steps below to test this part…

Front Loaders

To test the pressure switch in your front loader Kenmore washing machine, follow the steps below…

Step 1. To prevent any chances of electrocution, it is advised that you disconnect your washing machine’s power cord from the outlet before starting this repair.

Step 2. Loosen the screws holding the top panel to the cabinet using a Philips screwdriver. Slide the panel a few inches, then lift it off the cabinet.

Step 3. Take out the nuts holding the rear panel to the cabinet. Pry the rear panel off the cabinet and set it aside.

Step 4. Detach the wire harness from the pressure switch at the side of the cabinet. From the back of the machine, detach the pressure switch tube from the port at the back of the tub.

Step 5. Get a digital multimeter, then turn the dial to the continuity setting. Place the probes of the meter on the two outside terminals on the pressure switch (you should get an open circuit reading).

Step 6. Blow into the pressure tube, then pinch the tube shut. Inspect the meter’s display and look for a reading of about 0.2 ohms. If the reading is much higher or lower, the pressure switch will need to be replaced.

Step 7. Once you are satisfied that the pressure switch is in good condition, plug the wire harness back in. Reconnect the pressure tube to the port at the back of the tub.

Step 8. Snap the rear panel onto the cabinet, then apply the bolts using your Philips screwdriver.

Step 9. Place the top panel on the machine, then tighten the screws at the back. Plug your washing machine’s power cord back into the outlet.

Top Loaders

To test the pressure switch in your top loader Kenmore washing machine, follow the steps below…

Step 1. Disconnect your washing machine’s power cord from the outlet before starting this repair in order to prevent electrocution.

Step 2. Take out the bolts holding the rear panel to the cabinet using a Philips screwdriver. Pry the panel off the machine and set it aside.

Step 3. Release the retaining clamp holding the pressure tube to the air dome at the side of the tub. Detach the tube from the tub.

Step 4. Loosen the screws securing the control panel’s rear cover using your Philips screwdriver. Lift the panel off the cabinet and set it aside.

Step 5. Detach the wire harness attached to the pressure switch. Get a digital multimeter, then turn the dial to the continuity setting.

Step 6. Place the probes of the meter on the two outwards terminals on the pressure switch. Blow into the tube, then pinch it shut.

Step 7. For a working pressure switch, you should get a reading of about 0.5 ohms. If the reading is much higher or lower than this, the switch needs to be replaced.

Step 8. Once you are satisfied that the pressure switch is in good condition, reconnect the wire harness.

Step 9. Plug the pressure tube into the port at the side of the tub, then secure it using the retaining clamp.

Step 10. Snap the rear access panel onto the cabinet. Secure the panel by applying the bolts with your Philips screwdriver.

Step 11. Snap the control panel’s rear cover back on, then apply the screws. Plug your washing machine’s power cord back into the outlet.

Check out these other articles…

Maytag Washing Machine Will Not Start [How To Fix]

Kenmore Washing Machine Drain [Issues & Solutions]

Kenmore Washing Machine Is Leaking [How To Fix]

Kenmore Washing Machine Filter [Problems & Solutions]

Kenmore Washing Machine Is Not Filling With Water [How To Fix]

Kenmore Washing Machine Belt [Problems Solved]

Kenmore Washing Machine Heating [Issues & Solutions]

Kenmore Washing Machine Error Code OE — Quick Fix

The OE Kenmore washing machine error code indicates that the machine is having trouble draining. If you have a front loader washing machine, it could be as a result of a clogged pump filter. You’ll need to open the lower front access panel, take the filter out, and clean it.

The second thing that could prevent your washing machine from draining is a faulty pump. To inspect the pump assembly in your Kenmore washing machine, follow the steps below…

Front Loaders

Take the following steps to test the drain pump in your Kenmore front loader washing machine…

Step 1. Ensure that your washing machine is disconnected from the outlet before starting this repair in order to prevent electrocution.

Step 2. Go to the back of the washing machine, then use a Philips screwdriver to loosen the bolts holding the top panel to the cabinet. Pull the top panel backwards about an inch or so, then lift it off the machine.

Step 3. Slide the soap tray out of the dispenser. Press the little tab in the tray to completely release it from the housing.

Step 4. With your Philips screwdriver, loosen the bolts next to the dispenser opening. Take out the screws at the back of the control panel.

Step 5. Pry the control panel off the cabinet, then disconnect the wire harness. Set the control panel aside.

Step 6. Pry the lower front access panel open. Pull the emergency drain hose out of the retainers. Place a container underneath the hose.

Step 7. Pull the cap off the hose, then drain out any water stuck in the machine. Once all the water has drained out, put the cap back onto the hose.

Step 8. With your Philips screwdriver, loosen the nuts holding the pump filter housing. Pull the housing out of the cabinet.

Step 9. Loosen the single screw at the bottom of the front panel. Open the door of your washing machine.

Step 10. Using a flat-blade screwdriver or a pair of needle-nosed pliers, carefully pry out the retaining wire securing the door boot seal to the front panel. Carefully peel the seal off the door opening.

Step 11. Reach into the cabinet, then disconnect the door switch wire harness from behind the front panel.

Step 12. With your Philips screwdriver, take out the six screws at the top of the front panel. Carefully lift the front panel off the cabinet and set it aside.

Step 13. Note the positioning of the connectors attached to the drain pump assembly, the detach each one.

Step 14. With a pair of pliers, release the spring clamps holding the sump hose and outlet hose to the ports on the drain pump. Detach the hoses from the pump assembly (some water may spill out, so it is advised that you keep a rag nearby).

Step 15. Use your Philips screwdriver to take out the bolts holding the drain pump to the base of the cabinet. Pull the pump out of the cabinet.

Step 16. Get a digital multimeter, then turn the dial to the lowest setting for ohms of resistance. Place the meter’s probes on the terminals of the drain pump. For a working pump, you should get a reading of roughly 16 ohms.

Step 17. If the reading is significantly higher or lower than this number, the pump is damaged and should be replaced.

Step 18. Once you are satisfied that the pump is in good condition, install it in the cabinet, then apply the screws using your Philips screwdriver.

Step 19. Connect each wire harness to the appropriate terminal on the pump. Reconnect the sump hose and outlet hose to the pump, then secure them by sliding the retaining clamps into place.

Step 20. Lift the front panel and mount it on the cabinet. Apply the six screws at the top of the panel to secure it.

Step 21. Tighten the single screw at the bottom of the front panel. Push the pump filter housing back into place, then tighten the screws using your Philips screwdriver.

Step 22. Open the door of your machine. Reach into the cabinet, then reconnect the wire harness to the door lock assembly.

Step 23. Fit the door boot seal around the front panel. Using needle-nosed pliers, carefully fit the retaining wire around the door boot seal.

Step 24. Plug the wire harness back into the control panel. Snap the control panel onto the front of the cabinet, then tighten the screws at the back using a Philips screwdriver.

Step 25. Apply the nuts next to the dispenser opening. Slide the soap tray back into the dispenser.

Step 26. Place the top panel on the cabinet, then push it forwards. Secure the panel by tightening the screws at the back. Plug your washing machine back into the electrical outlet.

Top Loaders

To test the drain pump in your top loader Kenmore washing machine, follow the steps below…

Step 1. Ensure that your washing machine’s power cord is disconnected from the outlet before starting this repair in order to prevent electrocution.

Step 2. With a Philips screwdriver, loosen the bolts holding the rear panel to the cabinet. Pry the panel off the machine, then set it aside.

Step 3. Using your pliers, squeeze the retaining clamps holding the two hoses to the pump, then slide them out of place. Disconnect each hose from the drain pump (some water may leak).

Step 4. Disconnect the wire harness attached to the pump assembly. Take out the screws holding the pump to the base of the cabinet using a Philips screwdriver. Take the pump out of the cabinet.

Step 5. Get a digital multimeter, then turn the dial to the lowest setting for ohms of resistance.

Step 6. Place the probes of the meter on the pump terminals. For a working pump, you should get a reading of roughly 16 ohms.

Step 7. If the reading is significantly higher or lower than this number, the pump is damaged and needs to be replaced.

Step 8. Once you are sure that the pump is in good condition, reinstall it in the cabinet, then apply the bolts using your Philips screwdriver.

Step 9. Reconnect the wire harness to the pump assembly. Connect each of the hoses to the ports on the drain pump, then slide the retaining clamps into place.

Step 10. Snap the rear panel onto the cabinet, then apply the screws using your Philips screwdriver. Plug your washing machine’s power cord back into the outlet.

Kenmore Washing Machine Error Code DE — How To Fix

The DE Kenmore washing machine error code indicates that your washer’s door isn’t locked. Ensure that your washing machine’s door is firmly shut before starting a cycle.

If your washing machine’s door isn’t locking, it could be that the door switch has failed. Follow the steps below to test this part…

Front Loaders

To test the door lock assembly in your front loader Kenmore washing machine, follow the steps below…

Step 1. Ensure that your washing machine’s power cord is disconnected from the outlet before starting this procedure, in order to prevent any chances of electrocution.

Step 2. Open your washing machine’s door. Using a pair of needle-nosed pliers or a flat-blade screwdriver, pry the retaining band off the door boot seal (take care not to damage the seal).

Step 3. Peel the door boot seal off the front panel. With a Philips screwdriver, loosen the nuts holding the door lock assembly to the front panel.

Step 4. Reach into the cabinet, then disconnect the wire harness from the door lock assembly. Pull the door lock out of the cabinet.

Step 5. Get a digital multimeter, then turn the dial to the ohms setting. Place the probes of the meter on the two outward terminals of the door switch. For a working switch, you should get a closed circuit reading.

Step 6. If you don’t see anything on the meter’s display, the door switch is damaged and needs to be replaced. Once you are sure that the door switch is in good condition, reinstall it in the cabinet.

Step 7. Secure the door lock to the front panel by applying the Philips screws. Plug the wire harness back into the door switch.

Step 8. Carefully fit the door boot seal around the front panel. Fit the retaining band around the door boot seal using a flat-blade screwdriver. Plug your washing machine’s power cord back into the outlet.

See also  KitchenAid Washing Machine Water Inlet Valve [2 Issues & Proven Solutions]

Top Loaders

To test the door lock assembly in your Kenmore top loader washing machine, follow the steps below…

Step 1. In order to prevent any chances of electrocution, disconnect your washing machine’s power cord from the outlet before starting this repair.

Step 2. Pry the two end caps off the control panel. Loosen the bolts securing each end of the control panel to the cabinet. Lift the panel assembly over the washer’s rear panel.

Step 3. Detach the wire harness from the lid switch on the top panel. Get a digital multimeter, then turn the dial to the ohms setting.

Step 4. Place the probes of the meter on the two outer terminals on the lid switch. For a working switch, you should get a closed circuit reading on the meter’s display.

Step 5. if you don’t get a reading on the meter, the lid switch is damaged and should be replaced. Once you are satisfied that the lid switch is in good condition, plug the wire harness back in.

Step 6. Snap the control panel back into place, then apply the screws at each end. Snap the end caps onto the control panel. Plug your machine back into the outlet.

Dryers

To test the door lock assembly in your Kenmore dryer, follow the steps below…

Step 1. In order to prevent any chances of electrocution, ensure that your dryer is disconnected from the outlet before starting this repair.

Step 2. Go to the back of the machine, then loosen the bolts holding the top panel to the cabinet using a Philips screwdriver.

Step 3. Loosen the screws at the back of the control panel. Pry the panel off the front of the machine, then set it on top of the cabinet.

Step 4. Open the door of your dryer. Press the tab on the door lock at the top of the front panel to release it from the housing.

Step 5. Pull the door lock assembly out of place, then disconnect the wire harness. Get a digital multimeter, then turn the dial to the ohms setting.

Step 6. Place the meter’s probes on the two outer terminals of the door switch. For a working switch, you should get a closed circuit reading. If nothing shows up on the display, the switch is damaged and should be replaced.

Step 7. Once you are satisfied that the door lock is in good condition, reconnect the wire harness. Snap the door switch back into the front panel.

Step 8. Snap the control panel onto the front of the cabinet, then apply the bolts at the back using your Philips screwdriver.

Step 9. Place the washer’s top panel on the cabinet, then apply the bolts at the back. Reconnect your appliance to the outlet.

Kenmore Washing Machine Error Code E2 — Solved

The E2 Kenmore washing machine error code indicates an issue with the thermistor. For detailed steps on how to replace this part, read this article: Kenmore Washing Machine Heating.

Kenmore Washing Machine Error Code F02 — Quick Fix

The F02 Kenmore washing machine error code indicates that the appliance isn’t draining. For detailed steps on how to fix drainage issues in your washer, read this article: Kenmore Washing Machine Drain.

Kenmore Washing Machine Error Code F11 — Solution

The F11 Kenmore washing machine error code indicates that the control board is defective. Follow the steps below to replace this part…

Front Loaders

To replace the control board in your front loader Kenmore washing machine, follow the steps below…

Step 1. Ensure that your washing machine’s power cord is disconnected from the outlet before starting this repair in order to prevent any chances of electrocution.

Step 2. Go to the back of your machine, then take out the bolts securing the top panel using a Philips screwdriver. Slide the panel backwards about an inch or so, then lift off the cabinet.

Step 3. Pull the inlet tubes off the retainers on the steam generator. Using your screwdriver, loosen the bolts holding the cross bar to the cabinet. Slide the steam generator off the slots on the cabinet.

Step 4. Move the steam generator and cross bar aside. Loosen the bolt holding the pressure switch to the control board using a Philips screwdriver.

Step 5. Using needle-nosed pliers, release the control board’s wire harness retainers from the slots at the back of the cabinet.

Step 6. With your Philips screwdriver, take out the nuts holding the control board ti the cabinet. Slide the board out of place.

Step 7. Pry the cap off the control board (use a flat-blade screwdriver if needed). Disconnect each of the wires attached to the control board (ensure that you take note of where each plug goes).

Step 8. Prepare your new washing machine control board for installation by taking it out of its packaging. Plug each connector into its appropriate terminal on the new board.

Step 9. Snap the cover onto the new control board. Mount the new board on the cabinet, then apply the screws using your Philips screwdriver.

Step 10. Use your screwdriver to take out the bolts holding the rear panel to the cabinet. Lift the panel off the cabinet and set it aside.

Step 11. Reach into the cabinet, then snap the wire retainers into the slots at the back of the machine.

Step 12. Snap the rear panel back onto the cabinet, then apply the bolts with your Philips screwdriver.

Step 13. Mount the pressure switch on the new control board, then apply the screw. Push the steam generator and cross bar back into place. Secure the bar by applying the nuts.

Step 14. Push the inlet tubes into the slots on the steam generator. Place the top panel on the cabinet, then push it forwards.

Step 15. Secure the top panel by applying the bolts at the back with your Philips screwdriver. Plug your washing machine’s power cord into the outlet, then ensure that the issue has been fixed by running a cycle.

Top Loaders

To replace the control board in your Kenmore top loader washing machine, follow the steps below…

Step 1. Prevent any chances of electrocution by disconnecting your washer’s power cord from the outlet before starting this procedure.

Step 2. Go to the back of your machine, then loosen the screws securing the control panel’s rear cover using a Philips screwdriver. Pry cover off the machine and set it aside.

Step 3. Lift the control panel assembly off the base, then set it face-down on the cabinet. Loosen the bolts holding the control board cover to the control panel. Pry the cover off the board, then set it aside.

Step 4. Detach the wire plugs attached to the control board, then disconnect each one (ensure that you note where each connector goes).

Step 5. With your Philips screwdriver, take out the bolts holding the control board to the control panel assembly. Lift the board off the panel, then set it aside.

Step 6. Prepare the new control board for installation by taking it out of its packaging. Mount the new board on the panel, then tighten the screws with your Philips screwdriver.

Step 7. Plug each connector into its appropriate terminal on the new control board. Snap the cap onto the new board, then apply the screws with your Philips screwdriver.

Step 8. Lift the control panel assembly and snap it back into the base. Snap the rear cover onto the control panel, then apply the bolts.

Step 9. Plug your washing machines’ power cord back into the outlet, then ensure that the issue has been fixed by running a wash cycle.

Dryers

To replace the control board in your Kenmore dryer, follow the steps below…

Step 1. Disconnect your washing machine’s power cord from the outlet before starting this repair in order to prevent electrocution.

Step 2. From the back of the machine, use a Philips screwdriver to take out the bolts holding the top panel. Pull the top panel backwards about an inch or so, then lift it off the cabinet.

Step 3. Release the control board wire plugs from the retaining tabs. Detach the wires attached to the control board, then disconnect each one.

Step 4. With your Philips screwdriver, loosen the bolts holding the control board to the side of the cabinet. Pull the board off the machine, then discard it.

Step 5. Prepare the new control board for installation by taking it out of its packaging. Mount the new board on the cabinet, then apply the screws using your Philips screwdriver.

Step 6. Plug each wire connector into its appropriate terminal on the new board. Secure the wire in the retainers on the new board.

Step 7. Place the top panel on the cabinet, then push it forwards. Apply the screws at the back of the machine using your Philips screwdriver.

Step 8. Reconnect your appliance to the electrical outlet, then try running a cycle to ensure that the issue has been fixed.

Kenmore Washing Machine Error Code F20 — Solved

The F20 Kenmore washing machine error code indicates that your washing machine isn’t filling with water. There are various things that could cause this issue.

The first thing one should check if a washer won’t fill with water is the inlet filter. Your machine has two filters in the inlet ports at the back of the cabinet. Over time, dirt from the water supply can accumulate and clog the filters.

The second cause of this issue is a damaged water inlet valve. The inlet valve controls how much water flows into the machine. If the valve fails, your machine will not fill.

The final cause of this problem is a faulty pressure switch. The switch tells the inlet valve when to turn on and off. If this part fails, your washer can overfill, or not fill at all.

For detailed steps on how to fix filling issues in your washer, read this article: Kenmore Washing Machine Is Not Filling With Water.

Kenmore Washing Machine Error Code F24 — How To Fix

The F24 Kenmore washing machine error code indicates an issue with the temperature sensor. Before replacing this part, it’s important to test it first. Follow the steps below to do this…

Front Loaders

Take the following steps to test the thermistor in your front loader Kenmore washing machine…

Step 1. Ensure that your washing machine’s power cord is disconnected from the outlet before starting this repair in order to prevent electrocution.

Step 2. With someone assisting you, carefully move your washing machine forwards a bit to get more working space.

Step 3. Go to the back of the machine, then loosen the bolts holding the top panel to the cabinet using a Philips screwdriver. Slide the panel backwards about an inch or so, then lift it off the cabinet.

Step 4. Pull the soap tray out of the dispenser, then release it from the housing by pressing the little tab inside. Set the tray aside.

Step 5. Loosen the bolts next to the dispenser opening. Use your Philips screwdriver to loosen the screws at the back of the control panel. Pry the panel off the front of the cabinet.

Step 6. Using needle-nosed pliers, release the retainer securing the wire retainer to the front of the machine.

Step 7. Snap the control panel back onto the cabinet, then tighten the bolts at the back using your Philips screwdriver.

Step 8. Tighten the two bolts next to the dispenser opening. Push the soap tray into the dispenser.

Step 9. Disconnect the temperature sensor wire harness. Loosen the bolt holding the temp sensor to the top of the drum. Take the sensor off the tub.

Step 10. Get a digital multimeter, then turn the dial to the ohms setting. Place the probes of the meter on the sensor’s connector terminals. For a working sensor, you should get a reading of roughly 11,000 ohms. If the reading is much lower or higher than this number, the part needs to be replaced.

Step 11. Once you are satisfied that the sensor is in good condition, remount it on the tub, then apply the screws using your Philips screwdriver.

Step 12. Plug the thermistor wire harness back in, then snap the retainer into the cabinet.

Step 13. Place the top panel on the cabinet, then push it forwards. Secure the panel by applying the bolts at the back with your Philips screwdriver.

Step 14. Carefully move your washing machine back into place. Reconnect your appliance to the power outlet.

Top Loaders

To test the thermistor in your top loader Kenmore washing machine, follow the steps below…

Step 1. Ensure that you turn your washer’s water supply taps off and disconnect the power cord from the outlet before starting this repair in order to prevent electrocution and water leaks.

Step 2. Using a pair of pliers if needed, detach the HOT and COLD water supply hoses from the ports at the back of your machine (it is advised that you keep a rag nearby to clean any leaks).

Step 3. Pull your washer’s drain hose out of the standpipe. Carefully tip your washing machine forwards, then set it on the floor (get someone to assist you if needed).

Step 4. With a Philips screwdriver, take out the bolts holding the thermistor to the bottom of the tub. Take the thermistor off the machine, then disconnect the wire harness.

Step 5. Get a digital multimeter, then turn the control knob to the ohms setting. Place the probes of the meter on the thermistor connector terminals.

Step 6. For a working sensor, you should get a reading of roughly 11,500 ohms. If the reading is significantly higher or lower, you’ll need to replace the thermistor.

Step 7. Once you are satisfied that the thermistor is in good condition, remount it at the bottom of the tub, then apply the nuts using your Philips screwdriver.

Step 8. Plug the connector back into the thermistor. Carefully lift your washing machine onto its feet, then insert the drain hose into the standpipe.

Step 9. Reconnect the HOT and COLD water supply hoses to the ports at the back of the machine (ensure that you properly connect both hoses in order to prevent leakage).

Step 10. Plug your appliance back into the electrical outlet, then turn the water supply taps back on.

Dryers

Take the following steps to test the thermistor in your Kenmore dryer…

Step 1. Disconnect your appliance from the outlet before starting this repair in order to prevent electrocution.

Step 2. Using a Philips screwdriver, loosen the bolts at the back of the machine securing the top panel. Pull the panel backwards, then lift it off the cabinet.

Step 3. Take out the screws at the back of the control panel. Pry the panel off the mounting bracket, then set it on top of the cabinet.

Step 4. Reach into the space above the front panel, then disconnect the wire harness from the door switch. Take out the Philips screws at the top of the front panel.

Step 5. Open the door of your machine, then loosen the lower screws on the front panel. Carefully lift the panel off the machine and set it aside.

Step 6. Disconnect the moisture sensor wire connector and drum light connector at the top and bottom of the front bulkhead.

Step 7. Loosen the bolts holding the front bulkhead to the cabinet using a Philips screwdriver. Carefully lift the bulkhead off the machine, then set it aside.

Step 8. Reach underneath the drum, then push the idler pulley inwards to release the tension on the belt. Lift the belt and drum out of the machine, then set them aside.

Step 9. Disconnect the thermistor wire harness. Loosen the nuts holding the thermistor to the cabinet using a Philips screwdriver.

Step 10. Get a digital multimeter, then turn the dial to the ohms setting. Place the probes of the meter on the sensor’s connector terminals.

Step 11. Look for a reading of about 11,000 ohms. If the reading is much higher or lower than this, you’ll need to replace the sensor.

Step 12. Once you are satisfied that the sensor is in good condition, remount it on the cabinet, then apply the bolts. Plug the wire harness back into the sensor.

Step 13. Lift the belt and drum, then guide them into the cabinet. Reach underneath the drum, the loop the drive belt around the motor pulley and idler pulley in a zig-zag formation.

Step 14. Mount the front bulkhead on the cabinet, then apply the bolts using a Philips screwdriver.

Step 15. Reconnect the moisture sensor and drum light wire connectors back in. Mount the front panel on the cabinet, then tighten the screws at the lower section.

Step 16. Tighten the screws at the top of the front panel, then reconnect the door lock wire harness.

Step 17. Snap the control panel onto the front of the cabinet, then apply the bolts at the back using your Philips screwdriver.

Step 18. Place the top panel on the cabinet, then push it forwards. Secure the top panel by applying the bolts with your Philips screwdriver. Reconnect your washer to the outlet.

Kenmore Washing Machine Error Code F23 — Solution

The F23 Kenmore washing machine error code indicates that the machine isn’t heating. The following are the parts responsible for this issue and how to test them…

1. Faulty Heating Element

If your washing machine isn’t heating, the first thing you should check is the heating element. Follow the steps below to test this part…

Front Loaders

To test the heating element in your Kenmore front loader washing machine, follow the steps below…

Step 1. Turn your washing machine’s water supply taps off and disconnect the power cord from the outlet in order in order to prevent electrocution and water leakage.

Step 2. Detach the water supply hoses from the ports at the back of the machine (ensure that you keep a rag nearby to clean any leaks).

Step 3. Loosen the bolts securing the top panel using a Philips screwdriver. Slide panel backwards, then lift it off the cabinet.

See also  KitchenAid Washing Machine Is Stuck On Rinse [4 Issues & Quick Solutions]

Step 4. Pull the detergent tray out of the housing, then press the little tab inside to release it from the housing. Take out the two screws next to the dispenser opening using a Philips screwdriver.

Step 5. Take out the bolts at the back of the machine securing the control panel. Pry the panel off the front of the machine.

Step 6. Disconnect the wire harness from the control panel. Set the panel aside. Pry the pump filter access panel open.

Step 7. Pull the emergency drain hose out of the retainers, then loosen the screws securing the pump filter housing. Pull the housing out of the machine, then set it aside.

Step 8. Using your Philips screwdriver, take out the single screw at the bottom of the front panel. Open the door of the machine.

Step 9. With a flat-blade screwdriver or needle-nosed pliers, pry out the retaining band holding the door boot seal to the front panel (take care not to damage the seal). peel the seal off the front panel.

Step 10. Reach into the cabinet, then disconnect the wire harness from the door lock assembly at the back of the front panel.

Step 11. Loosen the at the top of the front panel using a Philips screwdriver. Carefully lift the front panel off the cabinet, then set it aside.

Step 12. Tip your washing machine backwards carefully, then support it (get someone to assist you if needed).

Step 13. Disconnect the wires attached to the heating element at the lower section of the tub (ensure that you take note of where each plug goes).

Step 14. Loosen the bolt holding the element to the housing using a 10mm socket wrench. Pry the heating element out of the housing using a flat-blade screwdriver.

Step 15. Get a digital multimeter, then turn the dial to the lowest setting for ohms of resistance.

Step 16. Place each probe of the meter on each of the heating element terminals. For a working heating element, you should get a reading of roughly 50 ohms. If the reading is much lower or higher, you’ll need to replace the heating element.

Step 17. Once you are satisfied that the heating element is in good condition, slide it into the housing at the bottom of the tub, then apply the bolt using your 10mm socket wrench.

Step 18. Plug each connector into its appropriate terminal on the heating element. Carefully lift your washing machine back onto its feet.

Step 19. Lift the front panel and carefully mount it on the cabinet. Apply the six screws at the top of the front panel.

Step 20. Apply the single screw at the bottom of the front panel. Push the pump filter housing into place, then apply the bolts using your Philips screwdriver.

Step 21. Open the door of your machine. Reach into the cabinet, then reconnect the wire harness to the door lock assembly.

Step 22. Fit the door boot seal around the front panel. Using needle-nosed pliers or a flat-blade screwdriver, carefully fit the retaining wire around the door gasket.

Step 23. Plug the wire harness into the control panel. Snap the control panel onto the front of the cabinet, then apply the bolts at the back using your Philips screwdriver.

Step 24. Tighten the screws next to the dispenser’s opening. Push the detergent tray into the housing.

Step 25. Place the top panel on the cabinet, then apply the bolts at the back using your Philips screwdriver.

Step 26. Reconnect the HOT and COLD water supply hoses to their corresponding ports at the back of the machine, then turn the water taps on.

Dryers

To test the heating element in your Kenmore dryer, follow the steps below…

Step 1. In order to prevent any chances of electrocution, ensure that your washing machine’s power cord is disconnected from the outlet before starting this procedure.

Step 2. Go to the back of the machine, then use a Philips screwdriver to take out the bolts holding the top panel. Pull the panel backwards a few inches, then lift it off the machine.

Step 3. With your Philips screwdriver, take out the bolts at the back of the control panel. Pry the panel off the mounting bracket, then place it on top of the cabinet.

Step 4. Disconnect the door lock wire connector at the top of the front panel. Open the door of the machine, then use your screwdriver to take out the bolts at the lower section of the door opening.

Step 5. Loosen the bolts at the top of the front panel. Carefully lift the front panel off the cabinet, then set it aside.

Step 6. Disconnect the moisture sensor wire harness at the lower side of the front bulkhead. Detach the drum light wire connector at the top of the bulkhead.

Step 7. Using your Philips screwdriver, loosen the bolts holding the front bulkhead to the cabinet. Lift the bulkhead off the machine, then set it aside.

Step 8. Reach into the cabinet underneath the drum, then unhook the drive belt from the idler pulley and motor pulley. Carefully lift the drum and belt out of the cabinet.

Step 9. Note the positioning of the connectors attached to the heating element, then detach each one. Disconnect the wires connected to the rear high-limit thermostat.

Step 10. With your Philips screwdriver, take out the bolts holding the heating element to the cabinet. Take the heating element out of the machine.

Step 11. Get a digital multimeter, then turn the control dial to the ohms setting. Place the probes of the meter on each of the heating element terminals. For a working element, you should get a reading of roughly 50 ohms.

Step 12. If the reading is much higher or lower than this number, you’ll need to discard the heating element and purchase a new one.

Step 13. Once you are satisfied that the heating element is in good condition, remount it on the cabinet, then apply the bolts using your Philips screwdriver.

Step 14. Plug the connectors into the appropriate terminals on the heating element. Plug each connector into the rear high-limit thermostat.

Step 15. Lift the drum and belt, then carefully guide them into the cabinet. Reach underneath the drum, then push the idler pulley inwards.

Step 16. Loop the drive belt around the motor pulley and idler pulley in a zig-zag formation. Slowly rotate the drum by hand to ensure that the belt is properly aligned.

Step 17. Mount the front bulkhead on the cabinet, then apply the nuts using a Philips screwdriver. Plug the moisture sensor and drum light connectors back in.

Step 18. Lift the main front panel and mount it on the cabinet. Apply the screws at the bottom of the door opening.

Step 19. Plug the door switch wire connector back in. Using your Philips screwdriver, apply the screws at the top of the front panel.

Step 20. Snap the control panel onto the front of the cabinet, then apply the bolts at the back with your Philips screwdriver.

Step 21. Place the top panel on the cabinet, then tighten the bolts using your screwdriver. Plug your washing machine’s power cord back into the outlet.

2. Failed Thermal Fuse (Dryers)

To test the thermal fuse in your Kenmore dryer, follow the steps below…

Step 1. Disconnect your dryer’s power cord from the outlet before starting this procedure, in order to avoid any chances of electrocution.

Step 2. Loosen the bolts at the back of the dryer securing the top panel. Pull the panel backwards about an inch or so, then lift it off the machine.

Step 3. With your Philips screwdriver, take out the screws at the back of the control panel. Pry the panel off the mounting bracket. Set the panel on top of the cabinet.

Step 4. Reach into the space above the front panel, then disconnect the wire harness from the door lock assembly.

Step 5. Open the dryer’s door, then use your Philips screwdriver to take out the screws at the bottom of the door opening.

Step 6. Loosen the bolts at the top of the front panel. Carefully lift the front panel off the machine, then set it aside.

Step 7. Disconnect the light assembly wire connector at the top of the front bulkhead. Detach the moisture sensor wire harness at the lower part of the bulkhead.

Step 8. With your Philips screwdriver, take out the bolts holding the front bulkhead to the machine. Carefully lift the bulkhead off the machine and set it aside.

Step 9. Carefully reach underneath the drum, then push the idler pulley to the side to release the tension on the drive belt. Unhook the drive belt from the motor pulley and idler pulley.

Step 10. Lift the drum and drive belt out of the cabinet carefully, then set them aside. Detach the wire harness attached to the thermal fuse on the cabinet.

Step 11. Take out the bolts holding the thermal fuse to the cabinet using a Philips screwdriver. Take the fuse off the machine.

Step 12. Get a digital multimeter, then place the probes on each of the fuse connector terminals. If the meter shows 0 ohms of resistance, the fuse is in good condition.

Step 13. If the meter’s display doesn’t change significantly, you’ll need to discard the fuse and purchase a new one.

Step 14. Once you are satisfied that the thermal fuse is in good condition, place it on the cabinet, then tighten the bolts using your Philips screwdriver. Plug the connector into the fuse.

Step 15. Lift the drum and belt, then carefully guide them into the cabinet. Reach underneath the drum, then loop the belt around the idler pulley and motor pulley in a zig-zag formation.

Step 16. Slowly rotate the drum by hand to ensure that the belt is properly aligned. Mount the front bulkhead on the cabinet, then tighten the screws with your Philips screwdriver.

Step 17. Plug the moisture sensor and light assembly wire connectors back in. Mount the front panel on the cabinet, then apply the screws at the bottom of the door opening.

Step 18. Plug the door switch wire connector back in. Use your Philips screwdriver to tighten the screws at the top of the front panel. Snap the control panel onto the front of the cabinet.

Step 19. Secure the control panel by applying the screws at the back. Place the top panel on the cabinet, then tighten the screws using your Philips screwdriver. Reconnect your appliance to the outlet.

3. Faulty Rear High-Limit Thermostat (Dryers)

To test the high-limit thermostat in your Kenmore dryer, follow the steps below…

Step 1. Ensure that your washing machine’s power cord is disconnected from the outlet before starting this procedure in order to prevent electrocution.

Step 2. Loosen the bolts holding the top panel to the cabinet. Slide the panel backwards about an inch or so, then lift it off the machine.

Step 3. Using your Philips screwdriver, loosen the bolts at the back of the control panel. Carefully pry the control panel off off the mounting bracket, then place it on top of the cabinet.

Step 4. Open your dryer’s door, then use a Philips screwdriver to take out the bolts at the bottom of the opening.

Step 5. Disconnect the door switch wire harness. Use your Philips screwdriver to take out the bolts at the top of the front panel. Carefully lift the front panel off the cabinet, then set it aside.

Step 6. Disconnect the light assembly wire harness at the top of the front bulkhead. Detach the moisture sensor connector at the lower section of the bulkhead.

Step 7. With your screwdriver, loosen the bolts holding the bulkhead to the cabinet. Lift the bulkhead off the machine and set it aside.

Step 8. Reach into the cabinet underneath the drum, then push the idler pulley inwards to release the tension on the belt. Take the belt off the motor pulley and idler pulley.

Step 9. Lift the drum and belt out of the cabinet carefully, then set them aside. Disconnect the rear high-limit thermostat wires (ensure that you take note of where each plug goes).

Step 10. Loosen the nuts holding the thermostat to the heater assembly using a Philips screwdriver. Take the thermostat off the machine.

Step 11. Get a digital multimeter, then turn the dial to the lowest setting for ohms of resistance.

Step 12. Place the probes of the meter on each thermostat terminal. If the meter reads 0 ohms of resistance, it indicates that the thermostat is in good condition. If the meter’s display doesn’t change significantly, the thermostat will need to be replaced.

Step 13. Once you are sure that the thermostat is in good condition, mount it on the heater assembly, then apply the screws with your Philips screwdriver.

Step 14. Plug each connector into its appropriate terminal on the thermostat. Lift the belt and drum, then guide them back into the cabinet.

Step 15. Reach underneath the drum, then loop the belt around the motor and idler pulleys (ensure that the belt is looped in a zig-zag formation). Rotate the drum by hand slowly to ensure that the belt is properly aligned.

Step 16. Lift the front bulkhead and mount it on the cabinet. Apply the bulkhead screws using your Philips screwdriver.

Step 17. Reconnect the moisture sensor and drum light wire connectors. Mount the front panel on the cabinet, then use your Philips screwdriver to apply the nuts at the bottom of the door opening.

Step 18. Reconnect the door switch wire harness. With your screwdriver, apply the nuts at the top of the front panel.

Step 19. Snap the control panel assembly onto the front of the cabinet. Secure the control panel by tightening the screws at the back using your Philips screwdriver.

Step 20. Place the top panel on the cabinet, then push it forwards. Secure top panel by applying the bolts at the back. Reconnect your machine to the outlet.

4. Faulty Blower High-Limit Thermostat (Dryers)

To test the blower’s high-limit thermostat in your Kenmore dryer, follow the steps below…

Step 1. In order to avoid electrocution, it is advised that you disconnect your machine from the outlet before starting this repair.

Step 2. From the back of the machine, use a Philips screwdriver to loosen the bolts holding the top panel. Pull the panel backwards a few inches, then lift it off the cabinet.

Step 3. Using your screwdriver, loosen the bolts at the back of the control panel. Pry the control panel off the mounting bracket, then set it on top of the cabinet.

Step 4. Disconnect the door switch wire connector at the top of the front panel. Open the dryer’s door.

Step 5. Using your Philips screwdriver, take out the nuts at the lower portion of the door opening. Remove the screws at the top of the front panel. Carefully lift the front panel off the cabinet and set it aside.

Step 6. Detach the light assembly wire harness at the top of the front bulkhead. Disconnect the moisture sensor wire connector at the lower section of the bulkhead.

Step 7. Loosen the nuts holding the bulkhead to the cabinet using a Philips screwdriver. Lift the bulkhead off the machine, then set it aside.

Step 8. Reach underneath the machine, then unhook the drive belt from the motor pulley and idler pulley. Lift the drum and belt out of the cabinet carefully, then set them aside.

Step 9. With your Philips screwdriver, loosen the nut securing the high-limit thermostat to the blower assembly. Disconnect the wire harness attached to the thermostat.

Step 10. Get a digital multimeter, then turn the control dial to the continuity setting. Place the probes of the meter on each terminal of the thermostat.

Step 11. If the meter’s display doesn’t change significantly, it indicates that there is no continuity. You’ll need to discard the thermostat and purchase a new one.

Step 12. Once you are sure that the thermostat is in good condition, remount it on the blower assembly, then apply the nut with your Philips screwdriver.

Step 13. Plug each wire harness into its appropriate terminal on the thermostat. Carefully lift the drum and drive belt, then guide them into the cabinet.

Step 14. Reach into the machine, then loop the drive belt back around the pulley wheels in a zig-zag formation. To ensure that the belt is properly aligned, try rotating the drum by hand.

Step 15. Mount the front bulkhead onto the machine. Secure the bulkhead by tightening the Philips screws.

Step 16. Reconnect the light assembly and moisture sensor wire connectors. Carefully mount the main front panel onto the cabinet, then tighten the screws at the bottom of the door opening.

Step 17. Plug the door switch wire harness back in, then use your Philips screwdriver to apply the nuts at the top of the panel.

Step 18. Snap the control panel back onto the mounting bracket. Secure the control panel by applying the screws at the back.

Step 19. Place the top panel on the cabinet, then push it forwards. Apply the bolts at the back of the machine. Plug your washing machine’s power cord into the outlet.

Kenmore Washing Machine Error Code F33 — Quick Fix

The F33 Kenmore washing machine error code indicates that the connection between the drain pump and control board has been lost. This issue is often caused by a loose connector. Follow the steps below to fix this issue…

Front Loaders

To properly connect the drain pump wire harness in your front loader Kenmore washing machine, follow the steps below…

Step 1. Disconnect your washing machine’s power cord from the outlet before starting this repair in order to prevent electrocution.

Step 2. From the back of your machine, loosen the bolts securing the top panel. Slide the top panel backwards about an inch or so, then lift it off the machine.

Step 3. Pull the soap tray out of the housing, then press the little tab inside to release it from the housing.

Step 4. Using your Philips screwdriver, loosen the bolts next to the dispenser opening. Take out the screws at the back of the control panel.

Step 5. Pry the control panel off the cabinet (use a flat-blade screwdriver if needed). detach the wire harness attached to the control panel. Set the control panel aside.

See also  Electrolux Washing Machine Detergent [Detailed Guide]

Step 6. Open the door of your washing machine. Using a flat-blade screwdriver, carefully pry out the retaining band holding the door boot seal (take care not to puncture the door seal).

Step 7. Peel the door boot seal off the front panel. Reach into the cabinet behind the front panel, then disconnect the wire harness from the door switch.

Step 8. Pry the pump filter access panel open, then pull the emergency drain hose out of the retainers.

Step 9. Using your Philips screwdriver, loosen the nuts holding the pump filter housing to the cabinet. Pull the housing out and set it aside.

Step 10. Take out the single screw at the bottom of the front panel. Using your Philips screwdriver, loosen the six screws at the top of the front panel. Carefully lift the main front panel off the cabinet and set it aside.

Step 11. Inspect the drain pump wire harness and ensure that it is properly attached. Once you are sure that the connector is properly attached, remount the front panel on the cabinet.

Step 12. Using your Philips screwdriver, apply the six screws at the top of the front panel, and the single screw at the bottom.

Step 13. Push the pump filter into the housing, then apply the two screws using your Philips screwdriver. Close the lower access panel.

Step 14. Open the door of your washing machine, then reconnect the wire harness to the door lock assembly.

Step 15. Carefully fit the door boot seal around the front panel. Fit the retaining band around the door boot seal using a flat-blade screwdriver.

Step 16. Plug the wire harness into the control panel, then snap it onto the cabinet. Use your screwdriver to apply the screws at the back of the panel.

Step 17. Tighten the bolts next to the dispenser opening. Push the detergent tray into the housing.

Step 18. Place the top panel on the cabinet, then apply the screws at the back using your Philips screwdriver.

Step 19. Plug your washing machine’s power cord into the outlet, then try running a cycle to ensure that the error code is gone.

Top Loaders

To inspect the drain pump connector in your top loader Kenmore washing machine, follow the steps below…

Step 1. Ensure that your washing machine’s power cord is disconnected from the outlet before starting this repair in order to prevent any chances of electrocution.

Step 2. Using a Philips screwdriver, take out the bolts at the back of the machine securing the rear panel. Pry the panel off the machine and set it aside.

Step 3. Inspect the wire harness attached to the drain pump assembly, then ensure it is properly connected.

Step 4. Once you are sure that the harness is properly attached, mount the rear panel on the cabinet, then tighten the screws.

Step 5. Reconnect your washing machine to the electrical outlet, then ensure that the issue has been fixed by running a cycle.

Kenmore Washing Machine Error Code F34

You don’t need to worry if you get the F34 Kenmore washing machine error code. This message simply indicates that clothes where detected in the drum during a Drum Clean cycle.

To fix this issue, simply disconnect your washing machine, then take the clothes out of the drum. Reconnect your machine to the outlet, then resume the cycle to ensure that the issue has been fixed.

Kenmore Washing Machine Error Code F70

The F70 Kenmore washing machine error code indicates that the display board has failed. If you have a front loader, it could also be that the motor control board has failed. To replace these parts, follow the steps below..

Motor Control Board

To replace the motor control board in your front loader Kenmore washing machine, follow the steps below…

Step 1. Disconnect your washing machine’s power cord from the outlet before starting this repair in order to prevent any chances of electrocution.

Step 2. Loosen the screws at the back of the machine securing the top panel. Lift the panel off the cabinet, then set it aside.

Step 3. Pull the detergent tray out, then release it from the housing by pressing the little tab inside.

Step 4. With a Philips screwdriver, loosen the bolts next to the dispenser opening. Take out the nuts at the back of the control panel.

Step 5. Pry the control panel off the cabinet. Disconnect the wire harness attached to the panel, then set it aside.

Step 6. Pry the pump filter access panel open, then pull the emergency drain hose out of the retainers. Loosen the nuts holding the pump filter housing. Pull the housing out of place, then set it aside.

Step 7. Use your Philips screwdriver to take out the single screw at the bottom of the front panel.

Step 8. Open the door of your washing machine. Using a flat-blade screwdriver, carefully pry the retaining wire off the door boot seal. Peel the door boot seal off the front panel.

Step 9. Reach into the machine behind the front panel, then disconnect the wire harness from the door lock assembly.

Step 10. Using your Philips screwdriver, remove the six screws at the top of the front panel. Carefully lift the front panel off the cabinet and set it aside.

Step 11. Reach into the cabinet, then pry the cover off the motor control board. Note the positioning of the wires attached to the board, then disconnect each one.

Step 12. Pry the wires out of the retainers on the board. Using your Philips screwdriver, loosen the screw securing the motor control board to the cabinet. Pull the board out of the machine and discard it.

Step 13. Prepare your new washing machine motor control board for installation by taking it out of its packaging.

Step 14. Install the new board in the cabinet, then apply the bolts using your Philips screwdriver. Plug each wire harness into its appropriate terminal in the board. Secure the wires in the retainers.

Step 15. Carefully lift the front panel and mount it on the cabinet. With your Philips screwdriver, apply the nuts at the top of the front panel.

Step 16. Tighten the single screw at the bottom of the front panel. Push the pump filter housing back into the front panel, then tighten the two screws. Close the pump filter access panel.

Step 17. Open your washing machine’s door. Reach into the cabinet, then reconnect the door switch wire harness.

Step 18. Fit the door boot seal around the front panel. Using needle-nosed pliers or a flat-blade screwdriver, fit the retaining band around the door boot seal.

Step 19. Reconnect the wire harness to the control panel assembly. Snap the panel onto the front of the machine. Using your Philips screwdriver, apply the nut at the back of the panel.

Step 20. Tighten the two screws next to the dispenser opening. Push the soap tray into the housing.

Step 21. Mount the top panel on the cabinet, then apply the bolts at the back using your Philips screwdriver.

Step 22. Reconnect your washing machine to the outlet. To ensure that the error code is gone, try running a wash cycle.

Display Board

To replace the display board in your Kenmore washing machine, follow the steps below…

Front Loaders

To replace the display board in your Kenmore front loader washing machine, follow the steps below…

Step 1. Ensure that your washing machine’s power cord is disconnected from the outlet before starting this repair in order to prevent any chances of electrocution.

Step 2. Using a Philips screwdriver, take out the bolts at the back of the machine securing the top panel. Slide the panel backwards a few inches, then lift it off the machine.

Step 3. Pull the soap tray out of the dispenser, then press the little tab inside to release it from the housing.

Step 4. Loosen the two bolts next to the dispenser opening using a Philips screwdriver. Take out the nuts at the back of the control panel

Step 5. Pry the control panel off the cabinet. Disconnect the wire harness attached to the control panel.

Step 6. Set the control panel face-down on a flat surface. Using your Philips screwdriver, loosen the bolts holding the display board to the control panel. Take the board off the panel, then discard it.

Step 7. Prepare the new washing machine display board for installation by taking it out of its packaging. Pry the selector knob off the old board, then transfer it to the new one.

Step 8. Mount the new board on the control panel, then apply the screws. Snap the control panel onto the front of the cabinet, then tighten the screws at the back using a Philips screwdriver.

Step 9. Plug the wire harness back into the display board. Tighten the two screws next to the dispenser opening.

Step 10. Push the detergent tray into the dispenser. Place the top panel on the cabinet, then push it forwards.

Step 11. Secure the top panel by tightening the bolts at the back. Reconnect your washing machine to the outlet. To ensure that the issue has been fixed, try running a wash cycle.

Top Loaders

Follow the steps below to replace the display board in your top loader Kenmore washing machine…

Step 1. Ensure that your washing machine’s power cord is disconnected from the outlet before starting this procedure in order to prevent any chances of electrocution.

Step 2. Use your Philips screwdriver to loosen the bolts holding the control panel’s rear cover to the cabinet. Pry the panel off the machine and set it aside.

Step 3. Detach the control panel assembly from the mounting bracket, then set it face-down on the cabinet.

Step 4. Using a Philips screwdriver, loosen the bolts holding the control board cover. Pry the cover off using a flat-blade screwdriver.

Step 5. Pry the display board wire connectors off the main control board. Loosen the screws holding the board assembly to the control panel.

Step 6. Using a flat-blade screwdriver, pry the display board and control board apart. Take your new display board out of its packaging.

Step 7. Pry the selector knob off the old display board, then transfer it to the new one. Snap the new display board to the control board.

Step 8. Place the board assembly on the control panel, then tighten the screws using a Philips screwdriver.

Step 9. Plug the new display board wires into the control board. Place the cover on the board assembly, then apply the bolts.

Step 10. Lift the control panel assembly and snap it into the mounting bracket. Place the rear cover on the control panel assembly, then tighten the screws.

Step 11. Plug your washer back into the electrical outlet, then ensure that everything works properly by running a cycle.

Dryers

Follow the steps below to replace the display board in your Kenmore dryer…

Step 1. Ensure that your appliance is disconnected from the outlet before starting this procedure in order to prevent any chances of electrocution.

Step 2. Loosen the screws at the back of the cabinet holding the top panel. Pull the top panel backwards about an inch or so, then lift it off the machine.

Step 3. Disconnect the control panel wire harnesses from the main control board mounted on the cabinet.

Step 4. Loosen the bolts at the back of the control panel. Pry the panel off the front of the machine.

Step 5. Set the control panel face-down on a flat surface. Take out the screws holding the display board to the control panel.

Step 6. Take your new dryer display board out of its packaging, then mount it on the control panel. Apply the screws to secure the new panel.

Step 7. Snap the control panel onto the front of the cabinet, then tighten the screws at the back to secure it. Plug the display board wires into the control board on the cabinet.

Step 8. Place the top panel back on the machine, then push it forwards. Secure the panel by applying the screws at the back.

Step 9. Plug your washing machine’s power cord back into the outlet, then try running a cycle to ensure that the error code is gone.

Kenmore Washing Machine Error Code UE — Solved

The UE Kenmore washing machine error code indicates that the appliance is unbalanced and unable to spin.

This is mostly caused by uneven feet. To fix this issue, tip your washing machine backwards carefully, then adjust the uneven leg as needed using a spanner. Set your washing machine back onto its feet, then use a spirit level tool to ensure it is properly balanced

It is also advised that you place your washing machine on a firm, even surface. If the machine isn’t properly leveled, the drum will tilt to the side; this will make it harder for the drum to spin.

Kenmore Washing Machine Error Code IE — Solution

This Kenmore washing machine error code indicates that the machine isn’t filling with water fast enough. The following are causes of this issue…

1. Inlet Taps Aren’t Open

If your Kenmore washing machine isn’t filling fast enough, the first thing to do is check to ensure that the taps are fully opened.

If the machine still doesn’t fill after opening the taps, the fault could be from the water supply. Shut the water taps, then disconnect the inlet hoses.

Place a bucket under the taps, then turn them on. If you notice that the water pressure isn’t high, you’ll need to contact a plumber to help you.

2. Hoses Are Bent

If your washing machine isn’t filling fast enough, the next thing to do is check the inlet hoses. If the hoses are bent or kinked in any way, the machine will not fill properly. Straighten the hoses as needed, then try running a cycle again to see if the issue has been fixed.

Kenmore Washing Machine Error Code 3E — Solution

The 3E Kenmore washing machine error code indicates that the wire connection to the motor is faulty. Follow the steps below to fix this issue…

Front Loaders

To inspect the drive motor in your front loader Kenmore washing machine, follow the steps below…

Step 1. In order to prevent any chances of electrocution, ensure that your machine is disconnected from the outlet before starting this repair.

Step 2. Using a Philips screwdriver, take out the bolts holding the rear access panel. Pry the panel off the cabinet, then set it aside.

Step 3. Inspect the wire connectors attached to the motor and ensure it is properly connected. If the motor terminals are burnt or look damaged, replace the motor.

Step 4. Once you are sure that the connectors are properly attached, snap the rear panel back on. Tighten the nuts to secure the rear panel.

Step 5. Plug your washer’s power cord back into the outlet, then try running a cycle to ensure that the error code is gone.

Top Loaders

To inspect the drive motor in your top loader Kenmore washing machine, follow the steps below…

Step 1. Ensure that you disconnect your washing machine from the power outlet and turn the water taps off before starting this repair in order to prevent leakage and electrocution.

Step 2. Using a pair of pliers, disconnect the water supply hoses from the ports at the back of the machine (ensure that you keep a rag nearby to clean any leaks).

Step 3. Pull your washer’s drain hose out of the standpipe. With someone assisting you, tip your washing machine forwards carefully, then set it on the floor.

Step 4. Use your screwdriver to loosen the bolts securing the belt guard. Take the guard off and set it aside.

Step 5. Inspect the wire harness attached to the motor and ensure that it is properly connected. If the contact points on the motor look burnt or damaged, you’ll need to replace the entire motor assembly.

Step 6. Once you are sure that the connector is properly attached, put the belt guard back in place, then tighten the screws.

Step 7. Carefully lift your washing machine onto its feet. Reinsert the drain hose into the standpipe.

Step 8. Reconnect the HOT and COLD water supply hoses to their corresponding ports at the back of the machine (make sure both hoses are properly attached so water doesn’t leak).

Step 9. Plug your washing machine back into the electrical outlet, then turn the water supply taps on. To ensure that the error code is gone, try running a cycle.

Dryers

To inspect the drive motor in your Kenmore dryer, follow the steps below…

Step 1. Disconnect your appliance from the outlet before starting this repair in order to prevent any chances of electrical damage.

Step 2. Using a Philips screwdriver, loosen the bolts at the back of the machine securing the top panel.

Step 3. Slide the top panel backwards about an inch or so, then lift it off the machine. Take out the nuts at the back of the control panel.

Step 4. Pry the control panel off the mounting bracket at the front of the machine. Place the control panel on top of the cabinet.

Step 5. Open the door of your machine, then take out the nuts at the lower section of the front panel using a Philips screwdriver.

Step 6. Disconnect the door switch wire harness at the top of the front panel. Using your screwdriver, take out the nuts at the top of the front panel. Carefully lift the front panel off the cabinet, then set it aside.

Step 7. Disconnect the moisture sensor wire harness at the lower section of the front bulkhead. Detach the drum light connector at the top of the bulkhead.

Step 8. Using your Philips screwdriver, loosen the bolts securing the front bulkhead to the cabinet. Carefully lift the bulkhead off the machine and set it aside.

Step 9. Reach underneath the drum carefully, then unhook the belt from the pulley wheels. Lift the drum and drive belt out of the cabinet carefully, then set them aside.

Step 10. Carefully inspect the wire harness attached to the motor assembly and ensure that it is properly connected. If the motor contact point is burnt or looks damaged, you’ll need to replace the entire motor.

Step 11. Once you are sure that the connector is properly attached, lift the belt and drum, then guide them back into the cabinet.

Step 12. Reach under the drum and hook the belt back onto the pulleys in a zig-zag formation.

Step 13. Remount the front bulkhead on the cabinet, then apply the screws using your Philip screwdriver. Plug the drum light and moisture sensor wire connectors back in.

Step 14. Mount the main front panel on the cabinet, then use your Philips screwdriver to tighten the bolts at the bottom of the front panel.

Step 15. Plug the door switch wire connector back in. Apply the screws at the top of the front panel.

Step 16. Snap the control panel onto the front of the cabinet, then apply the bolts at the back using your Philips screwdriver.

Step 19. Place the top panel on the cabinet and push it forwards. Secure the top panel by tightening the screws at the back.

Step 20. Plug your dryer into the electrical outlet, then try running a cycle to ensure that the error code is gone.