Candy Washing Machine Door [Issues & Solutions]

If you are experiencing issues with your Candy washing machine door, you’ve come to the right place. This detailed guide handles different door-related issues in your Candy washing machine. So, without wasting any more time, let’s get right to it…

Candy Washing Machine Door Not Locking — Solved

If your Candy washing machine door isn’t locking, you’ll need to replace the door lock assembly. Here’s how to do this…

How To Replace Candy Front Loader Washing Machine Door Lock

Here are the steps you’ll need to take in order to replace the door lock in your candy front loader washing machine…

Step 1. In order to avoid electrocution and water leakage, ensure that you turn off your washing machine’s water supply and unplug the power cord from your electrical outlet before attempting any repairs.

Step 2. Open the door of your washing machine and use a tool such as a flat-blade screwdriver to pry out the plastic retainer around the door boot seal. Peel the door boot seal back a bit away from the door lock and use a screwdriver to take out the two screws holding the lock to your washing machine.

Step 3. Reach behind the door boot seal and pull the door lock assembly out of the washing machine. Disconnect the electrical connector attached to the door lock and set the lock aside.

Step 4. Take your new door lock assembly out of its packaging and connect the electrical connector to it. Pop the new door lock assembly in place inside the washing machine and apply the two screws to secure it.

See also  How To Balance Electrolux Washer [Detailed Guide]

Step 5. Fit the door boot seal back around the door opening and run the retaining band back around it. Secure the band with the plastic clip, then close your washing machine’s door.

Step 6. Plug your washing machine back to its power outlet and turn on the water supply, then make sure everything is working properly by running a wash cycle.

How To Replace Candy Tumble Dryer Door Lock

Take the following steps to replace the door lock in your Candy tumble dyer…

Step 1. Make sure to unplug your washing machine from its power source before attempting any repairs in order to avoid electrocution.

Step 2. Go to the back of your washing machine and use a Philips screwdriver to take out the two screws holding the top panel. With the screws removed, slide the panel back, lift it off your washing machine, then set it aside.

Step 3. Reach inside the washing machine at the back of the control panel and disconnect the electrical connectors attached to it. Also use a Philips screwdriver to take out the two screws on each corner of the control panel. Disconnect the control panel from your washer and set it aside.

Step 4. Open the door off your machine and pull off the kick plate at the lower front section of your washing machine. Peel the door seal off the door opening and set it aside.

Step 5. Use a Philips screwdriver to take out the eight screws holding the main front panel of your washing machine. Pull the panel off the machine and disconnect the two electrical connectors at the back connected to the door lock assembly.

Step 6. Using your Philips screwdriver, remove the screw on the control panel holding the door lock assembly. Push the door lock assembly through the opening and set it aside.

See also  Back-Flow Into Washing Machine [How To Fix]

Step 7. Take your new door lock out of its packaging and snap it in place on the main front panel. Apply the screw to secure it.

Step 8. Connect each of the two electrical connectors to their appropriate terminals on the new door lock assembly and snap the main front panel of your machine back on. Apply the eight screws with your Philips screwdriver.

Step 9. Fit the door boot seal back around the door opening then close the door of your dryer.

Step 10. Snap the kick plate back in place at the lower front section of your dryer. Snap the control panel back in place and apply the two screws at the back to secure it. Connect the electrical connectors back to the control panel.

Step 11. Slide the top panel of your washing machine back on and apply the two screws at the back to secure it.

Step 12. Plug your washing machine back to its power outlet and turn on the water supply, then run a cycle to make sure everything is working properly.

Check out these other articles…

Washing Machine Not Spinning [Problems & Solutions]

Washing Machine Smells [Proven Solutions]

Washing Machine Vibrates Too Much [Easy Fix]

Washing Machine Turning On [Issues & Solutions]

Washing Machine Not Turning On [Proven Solutions]

Washing Machine Knob [Problems & Solutions]

Washing Machine Spinning [Guide, Problems & Solutions]

How To Replace Candy Washing Machine Door Seal — Quick Fix

To replace your Candy washing machine door seal, here are the steps you’ll need to take…

Step 1. Ensure that you turn off your washing machine’s water supply and unplug the power cord before attempting any repairs (this prevents any chances of electrocution and water leakage).

See also  Electrolux Washing Machine Noise [Problems & Solutions]

Step 2. Use a nut driver to take out the three screws at the back of your washing machine holding the top panel. Slide the top panel backwards then lift it off the washing machine.

Step 3. Open the door of your washing machine. Wedge a flat-blade screwdriver under the outer retaining band around the door boot seal and work the screwdriver around until you can take the whole band off.

Step 4. Peel the door boot seal away from the door opening and push the seal inside the drum. Reach inside the washing machine and use a Philips screwdriver to take out the screw holding the inner retaining band. Pull the door boot seal out of your washing machine.

Step 5. Take your new washing machine door boot seal out of its packaging. Lubricate the grooves of the door seal using some washing liquid.

Step 6. Push the new door seal inside the drum and fit it around the drum opening (make sure the indicator on the seal is lined up with the top of your washing machine).

Step 7. Reach inside the washing machine and fit the inner retaining band around the new door boot seal and apply the screw on the band to secure it.

Step 8. Fit the door boot seal around the door opening and run the outer retaining band around the door boot seal.

Step 9. Slide the top panel of your washing machine back on and apply the three screws at the back to secure it.

Step 10. Plug your washing machine back to its power source and turn on the water supply, then run a wash cycle to make sure everything is working properly.

Candy Washing Machine Door Not Opening — Solved

Here’s what you need to do if your candy washing machine door isn’t opening…

Step 1. Run some fishing line or garden wire around the door.

Step 2. Pull both ends of the string together away from the door lock (this will force the door lock to open manually).