If you are getting Candy washing machine error codes and you don’t know what to do, you’ve come to the right place. This guide explains the meanings of different error codes on your Candy washing machine…
Table of Contents
Candy Washing Machine Error Code E02 — How To Fix
If you are getting the Candy washing machine error code E02, it indicates that your machine isn’t filling. Here are the things that could cause this issue…
1. Blocked Water Inlet Filters
Here’s what you’ll need to do in order to clean the water inlet filters in your Candy washing machine…
Step 1. Ensure that you turn off your washing machine’s water supply and unplug the power cord before attempting any repairs in order to prevent electrocution and water leakage.
Step 2. Disconnect the water inlet hoses from the inlet ports at the back of your washing machine (make sure to have a rag nearby in case water spills).
Step 3. Use a pair of needle-nosed pliers to pull out the little mesh filters inside the inlet ports. Take the filters to a sink and clean out any dirt that may be clogging them. Put them back into the ports once you’ve cleaned them properly.
Step 4. Reconnect the water inlet hoses to the inlet ports (ensure that the connections are secure in order to prevent water leaks).
Step 5. Plug your washing machine back to its power outlet and turn on the water supply. Make sure everything is working properly by running a wash cycle.
2. Damaged Water Inlet Valve
Step 1. Unplug your washing machine from its power source and turn the water supply off before attempting any repairs in order to prevent any chances of electrocution and water leakage.
Step 2. Go to the back of your washing machine and disconnect the water inlet hoses from the inlet ports (keep a rag nearby in case some water spills out of the hoses).
Step 3. Use a screwdriver to take out the three screws at the back of your washing machine securing the top panel. Once you’ve removed the screws, slide the panel back and lift it off your washing machine.
Step 4. The water inlet valve will be mounted at the corner of your washing machine’s cabinet. Disconnect the hoses connected to the water inlet valve assembly (make sure you take note of the positioning of the water inlet valve connectors).
Step 5. Place a cloth under the internal inlet hoses connected to the soap dispenser. Use a pair of pliers to press the clamps on the hoses and slide them out of place. Disconnect the hoses from the soap dispenser assembly. Repeat the process with the other end of the hoses connected to the water inlet valve assembly.
Step 6. Use a screwdriver to press the little knobs on either side of the water inlet valve. Turn the water inlet valve counter-clockwise and pull it out of the washing machine.
Step 7. Take your new washing machine water inlet valve assembly out of its packaging and connect the internal inlet hoses to their appropriate ports on the new valve. Secure the connection by sliding the retaining clamps in place.
Step 8. Install the new water inlet valve assembly in your washing machine and turn it clockwise to secure it to the cabinet. Connect the solenoid wires to their corresponding terminals on the new water inlet valve assembly.
Step 9. Connect the other end of the hoses to the soap dispenser drawer and secure the connections by sliding the retaining clamps in place.
Step 10. Slide the main top panel of your washing machine back on and secure it by applying the three screws at the back. Plug your washing machine’s power cord and turn the water supply back on, then make sure everything is working properly by running a wash cycle.
Candy Washing Machine Error Code E03 — Solution
If you are getting the Candy washing machine error code E03, it indicates that something is preventing your washing machine from draining. Read this article to learn how to fix this issue.
Candy Washing Machine Error Code E08 — Solved
If your candy washing machine displays the E08 error code, it indicates an issue with the drive motor. Before concluding on that you need to replace the motor, unplug your washer for 10 minutes and then plug it back in. If the issue still persists, you’ll need to replace the motor. Click here to learn how to do this.
Candy Washing Machine Error Code E16 — Quick Fix
If you are getting the Candy washing machine error code E16, it indicates that there is an issue with the heater. To fix this problem, you’ll need to replace your washing machine’s heater. Here’s how to do this…
Step 1. Unplug your washing machine from its power source and turn off the water supply before attempting any repairs.
Step 2. Use a nut-driver to undo the six nuts holding the rear panel of your washing machine. Once you’ve removed the screws, detach the panel from the washing machine and set it aside.
Step 3. The heater element is mounted a the base of your washer’s tub. Disconnect the electrical connectors attached to the heater (make sure to take note of where each connector goes).
Step 4. Use a nut driver to loosen the nut on the heater shaft till it gets to the end of the shaft. Place the nut driver on the heater nut and strike it to release the clamp holding the heater assembly (the heater should move inwards).
Step 5. Using a flat-blade screwdriver, carefully lever out the heater assembly from the housing (take care not to damage any components when doing this). Set the old heater assembly aside.
Step 6. Take your new heater assembly out of its packaging. Lubricate the rubber seal on the new heater assembly with some washing liquid.
Step 7. Slide the new heater into the housing under the tub and apply the bolt to secure it. Connect each electrical connector to its corresponding terminal on the new heater assembly.
Step 8. Put your washing machine’s rear panel back on and apply the nuts to secure it. Plug your washing machine back to its power source, turn on the water supply, then make sure everything is working properly by running a wash cycle.
Check out these other articles…
Washing Machine Smells [Proven Solutions]
Washing Machine Not Working [How To Fix]
Candy Washing Machine Draining [How To, Issues & Solutions]
Candy Washing Machine Flashing [How To Fix]
Candy Washing Machine Bouncing [Easy Solution]
Candy Washing Machine Error Code E18 — How To Fix
If you are getting the Candy washing machine error code E18, it indicates that the control board is damaged and needs to be replaced. Here’s how to do this…
Step 1. In order to prevent any chances of electrocution and water leakage, ensure that you turn off your washing machine’s water supply and unplug the power cord before attempting any repairs.
Step 2. Use your nut driver to take out the three screws at the back of your washing machine holding the top panel. Slide the panel back a few inches and lift it off your washing machine.
Step 3. Pull the detergent drawer out of its housing and set it aside. Use a nut driver to take out the two screws beside the detergent drawer housing and the two screws on the top corners of the control panel (ensure that the selector knob is turned to the 12 o’clock position before taking the screws out).
Step 4. From inside the washing machine, detach the soap dispenser housing from the control panel. Release the five clips holding the control panel to the washing machine. Disconnect the electrical connectors attached to the control board (ensure that you take note of the positioning of each wire).
Step 5. Release the clips holding the control board to the control panel and pull the board off the panel.
Step 6. Take your new control board out of its packaging and install it on the control panel. Secure the new board by snapping the retaining clips in place.
Step 7. Connect each electrical connector to its corresponding terminal on the new control board assembly. Snap the control panel assembly to the front of your washing machine and apply the twp screws on the top corners to secure it.
Step 8. Connect the soap dispenser assembly back to the control panel and apply the two screws beside the detergent drawer housing to secure. Slide the soap drawer back in place.
Step 9. Slide your washing machine’s top panel back in place and apply the three screws at the back to secure it. Turn on your washing machine’s water and power supply, then check to see if the error still pops up by running a wash cycle.
Candy Washing Machine Error Code E21 — Solved
An E21 error code on your Candy washing machine indicates that the drainage process is taking too long. Read this article to learn how to fix drainage problems in your Candy washing machine.
Candy Washing Machine Error Code E07 — Solution
An E07 error code on your Candy washing machine indicates that there is an issue with the door lock. Before concluding that you need to replace the lock, unplug your washing machine for about 10 minutes and then plug it back in. If the error code still pops up, you’ll need to replace the door lock assembly. To learn how to do this, read this article.