Is your Bosch washing Machine Leaking? If so, this detailed guide gives you easy-to-follow steps on how to deal with the problem…
Table of Contents
Bosch Washing Machine Leaking Water Inlet Valve — Solved
Is your Bosch washing machine leaking from the water inlet valve? If so, you’ll need to replace it. Here’s how to do this…
Step 1. Ensure that your washing machine is unplugged from the power outlet and the water supply is turned off before starting this repair.
Step 2. Use your pliers to unscrew the two water supply hoses from the ports at the back of the machine (some water will spill out, so we recommend keeping a rag nearby).
Step 3. Using a Torx screwdriver, take out the bolts holding the top panel to the cabinet. Pull the panel backwards about an inch or so, then lift it off the machine.
Step 4. Use a pair of pliers to release the clamps on the tubes attached to the inlet valve, then slide them out of place. Pull each tube off the inlet valve.
Step 5. Unplug the electrical connectors attached to the valve. Use your Torx screwdriver to loosen the bolts holding the inlet valve to the cabinet. Pull the valve out of the machine, then discard it.
Step 6. Remove your new washer water inlet valve from its packaging. Mount the new inlet valve in the cabinet, then apply the screws to secure it.
Step 7. Connect the tubes to the ports, then secure them with the clamps. Connect the electrical connectors to the new valve.
Step 8. Put your machine’s top panel back on, then apply the screws to secure it. Reconnect the HOT and COLD water supply hoses to the ports at the back of the machine.
Step 9. Turn your washer’s water supply faucet back on, then plug the power cord back into the outlet.
Bosch Washing Machine Leaking At Bottom — Quick Fix
If your Bosch washing machine is leaking at the bottom, here are the issues to look for…
1. Damaged Pump
Here are the steps you’ll need to take to replace your washing machine’s drain pump…
Step 1. In order to prevent electrical damage, ensure that your washing machine is unplugged from the outlet before starting this repair.
Step 2. Use a Torx screwdriver to take out the bolts at the back of the machine securing the rear panel. Lift the panel off the cabinet, then set it aside.
Step 3. Pry the cap off the drain pump, then disconnect the wire harness attached to it. Release the spring clamp on the pump assembly, then slide it out of place. Pull the hose off the pump (some water may spill out, so keep a rag nearby).
Step 4. Use your screwdriver to take out the screws holding the drain pump to the cabinet. Pull the drain pump out of the cabinet, then discard it.
Step 5. Take your new washing machine drain pump out of its packaging. Install the new pump in the cabinet, then secure it by applying the screws with your screwdriver.
Step 6. Connect the hose to the port on the new pump, then secure it using the spring clamp. Plug the electrical connector to the pump assembly.
Step 7. Put the machine’s rear access panel back on, then apply the screws using your Torx screwdriver.
Step 8. Plug your machine back into its electrical outlet, then try running a wash cycle to ensure that the problem has been fixed.
2. Tub Seal Is Damaged
Replace your washing machine’s tub seal with the following steps…
Step 1. Unplug your washing machine from the electrical outlet and shut the water faucet before starting this repair.
Step 2. Using a Torx screwdriver, loosen the nuts at the back of the machine securing the rear panel. Lift the panel off the cabinet, then set it aside.
Step 3. Take the drive belt off the drive pulley and motor pulley. Disconnect the wire harness attached to the motor assembly.
Step 4. Use a socket wrench to take out the bolts securing the drive motor to the bottom of the tub. Carefully lift the motor out of the cabinet, then set it aside.
Step 5. Unscrew the two water supply hoses from the ports at the back of the machine (use a pair of pliers if needed).
Step 6. Loosen the screws holding the top panel to the cabinet. Pull the panel backwards, then lift it off the machine.
Step 7. Slide the soap tray out of the housing and press the tab to release it from the housing.
Step 8. Use your Torx screwdriver to take out the bolts holding the control panel to the front of the machine. Pry the panel off, then unplug each electrical connector attached to it (ensure that you take note of where each connector goes).
Step 9. Move the detergent dispenser out of the way. Use a pair of pliers to release the clamp on the detergent dispenser hose connected to the tub. Pull the hose off the tub assembly.
Step 10. Pry the lower front access panel off the cabinet and set it aside. Open the door of your machine.
Step 11. With your Torx screwdriver, loosen the screws securing the door lock to the cabinet.
Step 12. Using either a pair of needle-nosed pliers or a flat-blade screwdriver, pry the retaining wire off the door gasket (take care not to puncture the gasket.).
Step 13. Peel the door gasket off the cabinet. Use your Torx screwdriver to take out the screws at the top and bottom of the front panel. Carefully lift the entire panel off the cabinet, then set it aside.
Step 14. Use a 13mm socket wrench to loosen the bolts holding the counter-weights to the top and front of the tub. Pull each weight of the tub.
Step 15. Unplug the electrical connectors attached to the heating element at the bottom of the tub (take note of where each connector goes).
Step 16. Use a 10mm socket wrench to take out the bolt holding the heating element. Slide the heater out of the housing, then set it aside.
Step 17. Spread a rag on the floor underneath the tub. Use your screwdriver to loosen the screw-clamp holding the sump hose to the port at the tub. Pull the hose off.
Step 18. Use a 13mm socket wrench to take out the upper mounting bolts holding the two shock absorbers to the tub. Pull each shock out of its mount.
Step 19. Lift the two suspension springs holding the tub and unhook them from the cabinet. Carefully lower the tub assembly and guide it out of the cabinet.
Step 20. Turn the tub assembly upwards. Using a Torx screwdriver, loosen all the screws holding the two halves of the tub together. Lift the front half of the outer tub off the assembly, then set it aside.
Step 21. Use a flat-blade screwdriver to pry the tub seal out of the groove in the lower half of the outer tub.
Step 22. Discard the old tub seal and take the new one out of its packaging. Push the new tub seal into the groove in the tub.
Step 23. Lower the front half of the outer tub onto the tub assembly, then use your Torx screwdriver to apply the bolts.
Step 24. Carefully guide the tub assembly back into the machine. Hook the two suspension springs onto the cabinet.
Step 25. Push the two shock absorbers into the mounts at the bottom of the tub, then apply the upper mounting bolts using your 13mm socket wrench.
Step 26. Slide the heating element into the housing at the bottom of the tub, then apply the bolt using your 10mm socket wrench.
Step 27. Plug each electrical connector into the appropriate terminal on the heating element.
Step 28. Mount the motor assembly at the bottom of the tub, the apply the bolts to secure it. Plug the wire connector into the motor.
Step 29. Loop the drive belt around the motor pulley and drive pulley. Put the rear access panel onto the cabinet, then apply the screws using your Torx screwdriver.
Step 30. Reattach the sump hose to the port at the bottom of the tub, then tighten the screw-clamp to secure it.
Step 31. Mount the two counter-weights onto the tub assembly and apply the bolts using your socket wrench.
Step 32. Lift the front panel and snap it back onto the cabinet. Apply the bolts at the top and bottom of the panel using your Torx screwdriver.
Step 33. Connect the detergent dispenser hose to the port at the top of the tub, then secure it with the clamp.
Step 34. Snap the lower front access panel back onto the machine. Plug each electrical connector into its appropriate terminal on the control panel.
Step 35. Snap the control panel onto the cabinet, then use your Torx screwdriver to apply the nuts. Slide the soap tray into the detergent dispenser.
Step 36. Open your washer’s door. Push the door lock back into place and secure it by applying the screws with your Torx screwdriver.
Step 37. Fit the door boot seal back around the panel. Fit the retaining wire around the door gasket using a flat-blade screwdriver.
Step 38. Place the top panel onto the machine, then apply the screws at the back with your Torx screwdriver.
Step 39. Plug your washing machine back into the electrical outlet, then turn the water faucet back on. Ensure that the problem has been fixed by running a wash cycle.
Check out these other articles…
Amana Washing Machine Smells [How To Fix]
Amana Washing Machine Won’t Lock [How To Fix]
Bosch Washing Machine Error Codes [Meanings & Solutions]
Bosch Washing Machine Lock [Issues & Solutions]
Washing Machine Soap/Detergent [How To, Issues & Solutions]
3. Bearing Seal Is Damaged
To replace a damaged bearing seal in your Bosch washing machine, here are the steps you’ll need to take…
Step 1. Turn off your washing machine’s water supply faucet and disconnect the power cord from the outlet before starting this repair in order to prevent any chances of electrocution or water leakage.
Step 2. With your Torx screwdriver, loosen the bolts holding the top panel to the cabinet. Pull the panel backwards about an inch or so, then lift it off the machine.
Step 3. Slide the detergent drawer out of the housing, then press the tab to release it completely.
Step 4. Remove the screws holding the control panel to the cabinet using a Torx screwdriver. Pry the panel off the cabinet.
Step 5. Take note of the positioning of the electrical connectors attached to the control board, then unplug each one. Set the control panel aside.
Step 6. Go to the back of your washing machine and loosen the bolts securing the rear access panel. Lift the panel off the cabinet, then set it aside.
Step 7. Take the drive belt off the two pulleys and set it aside. Unplug the electrical connector attached to the motor at the bottom of the tub.
Step 8. With your socket wrench, loosen the bolts holding the drive motor. Carefully pull the drive motor out of the cabinet, then set it aside.
Step 9. Place a rag underneath the tub, then loosen the screw-clamp securing the sump hose. Pull the hose off the tub assembly.
Step 10. Go to the front of your machine. Pry the lower front access panel off the cabinet, then set it aside.
Step 11. Open the door of your washer. Carefully pry the retaining band off the door gasket using a flat-blade screwdriver.
Step 12. Using a Torx screwdriver, loosen the bolts holding the door lock assembly to the cabinet.
Step 13. Take out the screws at the top and bottom of the front panel. Lift the front panel off the machine, then set it aside.
Step 14. Use a pair of pliers to squeeze the retaining clamp on the detergent dispenser hose connected to the tub, then slide it out of place. Pull the hose off the machine.
Step 15. Using a 13mm socket wrench, loosen the bolts holding the counter-weights to the tub assembly. Carefully lift each weight off the machine, then set it aside.
Step 16. Take note of the positioning of each electrical connector attached to the heating element, then disconnect them.
Step 17. Use a 10mm socket wrench to loosen the nut securing the heating element to the housing. Slide the heating element out of the housing and set it aside.
Step 18. Use a pair of needle-nosed pliers to release the air pressure tube from the retainer.
Step 19. With a 13mm socket wrench, take out the upper mounting bolts securing the shock absorbers to the tub. Pull the shocks out of the mounts.
Step 20. Lift the two suspension springs, then lower the tub assembly. Carefully guide the tub out of the cabinet.
Step 21. Turn the tub upwards and set it on two supports. Use your Torx screwdriver to loosen the screws holding the two halves of the outer tub. Lift the front half of the outer tub off the tub assembly, then set it aside.
Step 22. Turn the tub assembly over. Use your socket wrench to loosen the bolt holding the drive pulley to the bottom of the tub. Take the pulley off, then set it aside.
Step 23. Turn the tub assembly over. Lift the inner tub out of the rear half of the outer tub, then set it aside.
Step 24. Use a flat-blade screwdriver or a chisel to pry the bearing seal out of the housing. Discard the old bearing seal, then take the new one out of its packaging.
Step 25. Push the new bearing firmly into the seat (use a mallet if needed). lower the inner tub into the outer tub.
Step 26. Turn the entire tub assembly over, then set it on the supports. Put the drive pulley back onto the shaft, then apply the bolts using your socket wrench.
Step 27. Turn the tub over again. Put the upper half of the outer tub onto the assembly and use your Torx screwdriver to apply all the screws.
Step 28. Carefully guide the entire tub into the cabinet. Lift the two suspension springs, then hook them onto the cabinet.
Step 29. Push the shock absorbers into the mounts, then apply the upper bolts using a 13mm socket wrench.
Step 30. Mount the drive motor at the bottom of the tub and secure it with the bolts. Plug the electrical connector back into the drive motor.
Step 31. Loop the drive belt back around the drive pulley and motor pulley. Slide the heating element into the housing, then apply the 10mm bolt to secure it.
Step 32. Plug each electrical connector into its appropriate terminal on the heating element. Snap the air pressure tube back into the retainer.
Step 33. Reconnect the sump hose to the port at the bottom of the tub. Secure the sump hose using the screw-clamp.
Step 34. Mount the two counter-weights onto the tub, then apply the bolts with your socket wrench.
Step 35. Push the detergent dispenser back in place and connect the dispenser hose to the port at the top of the tub. Secure the hose by sliding the spring clamp into place.
Step 36. Lift the front panel and snap it onto the machine. Using your Torx screwdriver, apply the bolts at the top and bottom.
Step 37. Reconnect each wire harness to its appropriate terminal on the control panel. Snap the panel onto the front of the machine, then use your screwdriver to apply the screws.
Step 38. Slide the soap tray back into the dispenser. Put the top panel on the cabinet and apply the screws at the back using your Torx screwdriver.
Step 39. Open your machine’s door and push the door lock back into place. Apply the screws with your screwdriver.
Step 40. Carefully fit the door gasket around the door opening. Secure the door gasket using the retaining wire.
Step 41. Turn your machine’s water supply faucet back on, then plug the power cord into the outlet. Try running a wash cycle to ensure that the problem has been fixed.
Bosch Washing Machine Leaking From Door — Quick Fix
If your Bosch washing machine is leaking from the door, it indicates that the door gasket has been punctured. To fix this issue, you’ll need to replace the seal. to learn how to do this, read this article.
Bosch Washing Machine Leaking From Drawer — Solved
If your Bosch washing machine is leaking from the drawer, it is most likely due to high water pressure. To solve this issue, try closing your machine’s water supply faucet when washing.