If you have having problems with Electrolux washing machine error codes, this guide will give you easy-to-follow steps on how to solve them…
Table of Contents
Electrolux Washing Machine Error Code E10 — Solved
This Electrolux washing machine error code indicates that something is preventing the washer from filling. Here are the most common causes of this issue…
1. Water Supply Is Off
If your machine doesn’t fill, the first thing you should check is the water supply faucet. You will not be able to run any wash cycles unless the water faucet is fully opened.
2. Inlet Filters Are Blocked
To clean clogged inlet filters in your Electrolux washing machine, here are the steps you’ll need to take…
Step 1. Turn off your washing machine’s water supply faucet in order to prevent leaks.
Step 2. Spread a rag on the floor underneath the water supply hoses to catch any leaks. Unscrew the COLD and HOT water supply hoses from the inlet ports (use a pair of pliers if needed).
Step 5. Use a pair of needle-nosed pliers to pull out the little mesh filter in each of the inlet ports.
Step 6. Take the filters to a sink and scrub out any dirt that may have clogged them using a soft brush.
Step 7. Once you’ve properly cleaned the filters, push them back into the ports. Reconnect the water supply hoses to the inlet ports.
Step 8. Turn your machine’s water supply faucet back on and try running a wash cycle to ensure that the problem has been fixed.
3. Water Inlet Valve Is Damaged
To replace a failed water inlet valve in your Electrolux washing machine, here are the steps you’ll need to take…
Step 1. Before starting this repair, ensure that you turn off the water supply faucet and disconnect the power cord from the outlet in order to prevent electrocution and water leakage.
Step 2. Using a pair of pliers, unscrew the two water supply hoses from the ports at the back of your machine (ensure that you keep a rag nearby in case water spills out).
Step 3. Using your Philips screwdriver, take out the bolts at the back of the machine securing the top panel. Pull the top panel backwards about an inch or so, then lift it off the cabinet.
Step 4. Use your screwdriver to take out the nuts holding the vibration dampener to the top of the tub assembly. Take the vibration dampener block off the assembly, then set it aside.
Step 5. Unplug the wire harness of the power cord. Disconnect the power cord grounding wire from the panel. Use a pair of needle-nosed pliers to release the wire retainer from the cabinet.
Step 6. Using your Philips screwdriver, loosen the screws holding the drain hose retainer to the back of the machine. Pull the retainer off the hose, then set it aside.
Step 7. Loosen the screws holding the main top bracket to the rear panel. Lift the bracket off the cabinet.
Step 8. Remove the bolts holding the rear panel to the cabinet. Lift the panel off the machine, then set it aside.
Step 9. Unplug the wire connectors attached to the water inlet valve assembly (ensure that you take note of where each connector goes).
Step 10. Use your Philips screwdriver to take out the screws holding the inlet valve assembly to the detergent dispenser. Pull the inlet valve off the dispenser, then discard it.
Step 11. Prepare your new washing machine water inlet valve for installation by removing it from its packaging.
Step 12. Transfer the outer port gaskets from the old inlet valve to the new one. Mount the new inlet valve on the dispenser, then apply the screws using your Philips screwdriver.
Step 13. Plug each electrical connector into its appropriate terminal on the new water inlet valve assembly.
Step 14. Lift the rear panel and mount it on the cabinet. Secure the rear panel by applying the screws with your Philips screwdriver.
Step 15. Place the support bracket on the rear panel, then use your screwdriver to apply the bolts.
Step 16. Reattach the grounding wire to the support bracket. Reconnect the power cord wire harness, then snap the retainer into the frame.
Step 17. Slide the retainer onto the drain hose, then use your Philips screwdriver to apply the bolts.
Step 18. Place the vibration dampener on top of the tub, then apply the screws using your screwdriver.
Step 19. Mount the top panel on the cabinet, then use your Philips screwdriver to apply the bolts at the back.
Step 20. Reconnect the HOT and COLD water inlet hoses to the ports at the back of your machine (ensure that the hoses are secured properly in order to prevent water leaks).
Step 21. Plug your washing machine back into the electrical outlet, then turn the water faucet back on. To ensure that the problem has been fixed, try running a wash cycle.
Electrolux Washing Machine Error Code E20 — How To Fix
This Electrolux washing machine error code indicates that the machine is unable to drain. If your washing machine doesn’t drain water, here are the causes…
1. Blocked Pump Filter
To clean a blocked pump filter in your Electrolux washing machine, here are the steps you’ll need to take…
Step 1. Unplug your machine from the power outlet before starting this repair in order to prevent electrocution.
Step 2. Pry open the lower front access panel. Spread a rag on the floor in front of the machine to catch any water leaks.
Step 3. Pull the emergency drain hose out. Place a contained underneath the hose. Pull the hose’s cap off, then drain out any water stuck in the machine.
Step 4. Once all the water has drained out of the machine, put the hose’s cap back on and push the hose back into place.
Step 5. Turn the pump filter knob and take it out of the housing. Clean out any lint and debris that may have accumulated in the filter.
Step 6. Once you’ve cleaned the pump filter thoroughly, push it back into place. Close the lower access panel.
Step 7. Plug your machine back into the electrical outlet, then try running a wash cycle to ensure that the issue has been resolved.
2. Damaged Drain Pump
To replace a damaged pump assembly in your Electrolux washing machine, here are the steps you’ll need to take…
Step 1. Ensure that your washing machine is disconnected from the power outlet before starting this repair in order to prevent electrocution.
Step 2. Use a Philips screwdriver to take out the bolts at the back of the machine holding the top panel. Pull the top panel backwards a few inches, then lift it off the cabinet.
Step 3. Open the door of your washing machine. Using either a pair of needle-nosed pliers or a flat-blade screwdriver, pry the retaining wire off the door gasket (take care not to puncture the gasket).
Step 4. Peel the door gasket off the panel. Tip your machine backwards carefully and place a support under the front.
Step 5. With your Philips screwdriver, take out the four screws at the bottom of the front panel. Set your machine back onto its feet.
Step 6. Slide the soap tray out, then fully release it by pressing the tab. Loosen the screws at the top of the panel and next to the detergent dispenser.
Step 7. Lift the front panel off the cabinet carefully. Disconnect the electrical connectors attached to the panel, then set it aside.
Step 8. Unplug the electrical connector attached to the pump assembly. Use a pair of needle-nosed pliers to release the wire from the retainer.
Step 9. Use a pair of pliers to squeeze the clamps holding the inlet and outlet hoses to the ports on the pump assembly, then slide them out of place.
Step 10. Pull each hose off the pump assembly (keep a rag nearby in case water spills out).
Step 11. Loosen the bolts holding the drain pump assembly to the cabinet using a 5/16 inch nut-driver.
Step 12. Take the pump assembly out of the cabinet, then discard it. Remove your new washing machine drain pump from its packaging.
Step 13. Ensure that the three rubber mounts are pushed into the holes on the cabinet. Place the new pump in the machine, then connect the inlet and outlet hoses to their appropriate ports. Slide the retaining clamps into place to secure them.
Step 14. Use your 5/16 inch nut-driver to apply the bolts to secure the new drain pump assembly.
Step 15. Snap the wire connector back into the retainer, then connect it to the new pump assembly.
Step 16. Plug each electrical connector to the front panel. Lift the front panel carefully, then snap it onto the cabinet.
Step 17. Use your screwdriver to apply the screws at the top of the front panel. Slide the detergent tray back into the dispenser.
Step 18. Tip your machine backwards a bit, then apply the four screws at the bottom of the front panel. Set your machine on its feet.
Step 19. Fit the door boot seal around the front pane. Use your needle-nosed pliers to fit the retaining band around the gasket.
Step 20. Place the top panel on the cabinet, then apply the screws at the back using your Philips screwdriver.
Step 21. Plug your washing machine back into the electrical outlet. To make sure the issue has been fixed, try running a wash cycle.
Electrolux Washing Machine Error Code E35 — Solution
The E35 error code in your Electrolux washing machine indicates that the machine is overfilling. The most common culprit is the water level switch. Here’s how to replace this part…
Step 1. In order to prevent electrical damage, ensure that your washing machine is unplugged from the power outlet before starting this repair.
Step 2. Loosen the screws at the back of the machine securing the top panel using a Philips screwdriver. Pull the panel backwards a few inches, then lift it off the machine.
Step 3. Rotate the water pressure switch and pull it off the cabinet. Unplug the wire connector attached to the pressure switch.
Step 4. Squeeze the clamp holding the air pressure tube to the pressure switch, then slide it out of place. Pull the hose off the switch.
Step 5. Discard the old water pressure switch, then take the new one out of its packaging.
Step 6. Connect the air pressure tube to the new switch, then secure it by sliding the retaining clamp in place.
Step 7. Plug the wire harness into the new water level switch. Snap the switch into the cabinet, then rotate it to secure.
Step 8. Place the top panel on the cabinet, then apply the bolts at the back using a Philips screwdriver.
Step 9. Plug your washing machine back into the electrical outlet, then ensure that the issue has been fixed by running a wash cycle.
Check out these other articles…
How To Clean Electrolux Washing Machine [Detailed Guide]
How To Reset Electrolux Washing Machine [Detailed Guide]
Electrolux Washing Machine Stuck [Proven Solutions]
Electrolux Washing Machine Not Spinning [Proven Solutions]
Electrolux Washing Machine Filter [Problems & Solutions]
Electrolux Washing Machine Error Code E40 — Quick Fix
This Electrolux washing machine error code indicates that the door lock has failed. Here are the steps you’ll need to take to replace this part…
Step 1. Make sure your washing machine’s power cord is unplugged from the outlet before starting this repair.
Step 2. Open the door of your washing machine. Use a Philips screwdriver to remove the screws holding the door trim locking plate. Take the door trim off the front panel, then set it aside.
Step 3. Use your Philips screwdriver to take out the screws holding the door lock to the front of the cabinet. Pull the door lock off the cabinet, then unplug the electrical connector attached to it.
Step 4. Discard the old door lock and take the new one out of its packaging. Plug the electrical connector to the new door lock.
Step 5. Install the new door lock assembly on the cabinet, then apply the screws to secure it.
Step 6. Put the door trim back on the panel, then use your Philips screwdriver to apply the screw on the locking plate.
Step 7. Close your machine’s door and plug the power cord back into the outlet. Turn your machine on to see if the error code is gone.
Electrolux Washing Machine Error Code EF0 — Solution
The EF0 error code in your Electrolux washing machine indicates that the door seal is leaking. If your machine’s door gasket is punctured, it will need to be replaced. Here’s how to do this…
Step 1. In order to prevent electrical damage, ensure that your washing machine is disconnected from the outlet before starting this repair.
Step 2. Move your washing machine forwards a bit to get more working space. Using a Philips screwdriver, remove the screws at the back of the machine holding the top panel. Slide the panel backwards about an inch or so, then lift it off the machine.
Step 3. Open your washing machine’s door. Using either a pair of needle-nosed pliers or a flat-blade screwdriver, take the retaining wire off the door gasket.
Step 4. Peel the door boot seal off the front panel. With the help of another person, tip the machine backwards carefully, then place a support underneath the front.
Step 5. Use your Philips screwdriver to loosen the four screws at the bottom of the front panel. Remove the support and set your machine back onto its feet.
Step 6. Slide the soap tray out, then press the tab to completely release it from the detergent dispenser.
Step 7. Loosen the screws next to the detergent dispenser and the screws at the top of the front panel using a Philips screwdriver.
Step 8. Lift the front panel off the cabinet, then unplug the electrical connectors attached to the panel. Set the front panel aside.
Step 9. Using a 7/16 inch socket wrench, take out the bolts holding the lower counter-weight to the front of the tub. Carefully lift the weight off the tub assembly, then set it aside.
Step 10. Pull the light assembly off the port at the top of the door boot seal. Use a pair of pliers to cut the zip-ties holding the re-circulation hose and dispenser tube to the door boot seal. Pull both hoses off the seal.
Step 11. Pry the inner retaining wire off the door boot seal. Peel the boot seal off the drum, then discard it.
Step 12. Remove your new washing machine door boot seal from its packaging. With the ports facing upwards, fit the new door boot seal around the front panel.
Step 13. Fit the inner retaining wire around the new door boot seal (if needed, use a flat-blade screwdriver or a pair of needle-nosed pliers).
Step 14. Connect the re-circulation tube and soap dispenser tube to the ports at the top of the new door boot seal. Secure the hoses using zip-ties.
Step 15. Push the light assembly into the port on the door boot seal. Lift the counter-weight and mount it on the tub assembly. Secure the weight by applying the bolts with your 7/16 inch socket wrench.
Step 16. Reconnect the electrical connectors back to the front panel. Lift the front panel and snap it onto the cabinet. Apply the screws at the top of the panel using a Philips screwdriver.
Step 17. Slide the soap tray back into the detergent dispenser. Carefully tip your machine backwards, then use your Philips screwdriver to apply the four screws at the bottom.
Step 18. Open the door of your washing machine and fit the new door boot seal around the front panel. With a flat-blade screwdriver or a pair of needle-nosed pliers, fit the retaining wire around the new door gasket.
Step 19. Close your washing machine’s door. Place the top panel on the cabinet, then use your Philips screwdriver to apply the screws at the back.
Step 20. Plug your washing machine’s power cord back into the electrical outlet, then try running a wash cycle to ensure that everything works properly.
Electrolux Washing Machine Error Code 50 — How To Fix
This error code indicates that the drum is unable to turn. Here are the causes of this problem…
1. Defective Motor Control Board
To replace a damaged motor control board in your Electrolux washing machine, here are the steps you’ll need to take…
Step 1. Shut your washing machine’s water supply faucet and disconnect the power cord from the outlet before starting this repair.
Step 2. Unscrew the COLD and HOT water supply hoses from the inlet ports at the back of the machine (ensure that you keep a rag nearby to clean any water leaks).
Step 3. With a Philips screwdriver, loosen the screws at the back of the machine securing the top panel to the cabinet. Slide the panel backwards, then lift it off the machine.
Step 4. Use your screwdriver to take out the screws holding the vibration dampener to the top of the tub. Lift the block off the tub, then set it aside.
Step 5. Unplug the electrical connector of the power cord, then disconnect the grounding wire.
Step 6. Loosen the screws holding the retainer to the drain hose at the back of the machine. Pull the retainer off and set it aside.
Step 7. Remove the bolts holding the main top bracket to the rear panel. Take the panel off the cabinet and set it aside.
Step 8. Use your screwdriver to remove the screw holding the motor control board to the rear panel. Take out the screws securing the rear panel.
Step 9. Lift the rear panel off the cabinet, then set it aside. With your Philips screwdriver, take out the bolts holding the motor control board to the cabinet.
Step 10. Pry the plastic cover off the control board. Disconnect the electrical connectors attached to the board (ensure that you take note of where each plug goes).
Step 11. Use a pair of pliers to release the wire retainers from the control board. Discard the old motor control board, then remove the new one from its packaging.
Step 12. Plug each electrical connector into the appropriate terminals on the new control board, then snap the retainers in.
Step 13. Mount the control board on the cabinet, then use your Philips screwdriver to apply the screws.
Step 14. Lift the rear panel and mount it on the cabinet. Use your screwdriver to apply all the bolts. Put the bracket onto the rear panel and apply the bolts to secure it.
Step 15. Reconnect the wire harness of the power cord. Reattach the grounding wire to the panel.
Step 16. Place the vibration dampening block on the tub, then apply the screws using your Philips screwdriver.
Step 17. Place the top panel on the cabinet and secure it by applying the screws. Reattach the two water supply hoses to the ports at the back of your machine (ensure that the hoses are secured properly in order to prevent water leaks).
Step 18. Reconnect the power cord to the outlet, then turn the water supply. To ensure that the issue has been fixed, try running a cycle.
2. Damaged Drive Motor
To replace a damaged drive motor in your Electrolux washing machine, here are the steps you’ll need to take…
Step 1. In order to prevent electrocution and water leakage, ensure that your washing machine’s water supply is turned off, and the power cord is unplugged from the outlet.
Step 2. Spread a rag on the floor underneath the water inlet hoses at the back of the machine. Unscrew the COLD and HOT water supply hoses from the inlet ports (some water may spill out).
Step 3. With a Philips screwdriver, loosen the bolts at the back of the machine securing the top panel. Pull the panel backwards about an inch or so, then lift it off the machine.
Step 4. Take out the nuts securing the vibration dampening block to the tub. Carefully lift the block off the tub assembly and set it aside.
Step 5. Unplug the power cord grounding wire, then disconnect the electrical connector.
Step 6. Remove the screws holding the mounting bracket to the rear panel. Take the bracket off and set it aside.
Step 7. With your Philips screwdriver, loosen the screws holding the drain hose retainer. Take the retainer off.
Step 8. Use your screwdriver to remove the bolts securing the rear panel to the cabinet. Carefully lift the rear panel off and set it aside.
Step 9. Carefully take the drive belt off the drive pulley and motor pulley, then set it aside.
Step 10. Using a 5/16 inch nut-driver, take out the bolts holding the drive motor to the bottom of the tub. Carefully take the motor off the mounts.
Step 11. Unplug the wire harness attached to the motor and release the wires from the retainer. Set the old drive motor aside and take the new one out of its packaging.
Step 12. Plug the wires to the new motor assembly, then snap the wires into the retainer.
Step 13. Mount the drive motor at the bottom of the tub, then apply the bolts using your 5/16 inch nut-driver.
Step 14. Loop the drive belt around the two pulleys (ensure that the grooved side is turned inwards).
Step 15. Place the rear panel back onto the machine, then apply the screws using your Philips screwdriver.
Step 16. Put the drain hose retainer back in place, then secure it by applying the screws. Put the bracket onto the rear panel and secure it with the bolts.
Step 17. Reconnect the power cord wire connector and grounding wire. Put the vibration dampening block back in place, then apply the screws to secure it.
Step 18. Mount the top panel on the cabinet, then apply the screws using your Philips screwdriver.
Step 19. Reconnect the COLD and HOT water supply hoses to the inlet ports at the back of the machine.
Step 20. Turn your washer’s water supply faucet back on, then plug the power cord back into the outlet. To make sure the issue has been fixed, try running a spin cycle.
3. Worn Drive Belt
To replace a worn/damaged drive belt in your Electrolux washing machine, here are the steps you’ll need to take…
Step 1. In order to prevent electrical damage, ensure that your washing machine is unplugged from the power outlet before starting this repair.
Step 2. Using a Philips screwdriver, take out the screws holding the rear panel to the cabinet. Lift the panel upwards, then take it off the cabinet.
Step 3. If still intact, take the drive belt off the motor pulley and drive pulley. Discard the old belt and remove the new one from its packaging.
Step 4. With the grooved side turned inwards, loop the new drive belt around the two pulleys.
Step 5. Place the rear panel on the cabinet, then apply the bolts with your Philips screwdriver.
Step 6. Plug your washing machine back into the electrical outlet, then try running a cycle to ensure that the issue has been resolved.
4. Damaged Drive Pulley
Here are the steps you’ll need to take to replace the drive pulley in your Electrolux washing machine…
Step 1. In order to prevent electrical damage, we recommend unplugging your machine from the outlet before starting this repair.
Step 2. Loosen the screws securing the rear panel to the cabinet using a Philips screwdriver. Take the panel off the cabinet and set it aside.
Step 3. Carefully take the drive belt off the two pulleys, then set it aside. Jam the drive pulley using a screwdriver.
Step 4. Using a 6mm hex-head socket, loosen the nut holding the drive pulley to the back of the machine. Take the pulley off the shaft, then set it aside.
Step 5. Prepare your new drive pulley for installation by removing it from its packaging. Place the new belt on the shaft, then apply the bolt with your 6mm socket.
Step 6. Loop the drive belt around the two pulleys. Place the rear panel on the cabinet, then use your screwdriver to apply the screws.
Step 7. Reconnect your washing machine to the power outlet, then try running a wash cycle to see if the issue has been resolved.
5. Damaged Drum Bearings
If your machine’s drum doesn’t spin freely by hand, it indicates that the bearings have gone bad. Depending on the model of your machine, you’ll need to replace the entire rear half of the inner tub.
Take the following steps to replace the rear half of the outer tub in your Electrolux washing machine…
Step 1. In order to prevent electrical damage and water leaks, unplug your machine from the power outlet and turn the water faucet off before starting this repair.
Step 2. Spread a rag on the floor underneath the water supply hoses at the back of the machine. Unscrew the two inlet hoses from your machine.
Step 3. Loosen the screws holding the rear panel to the cabinet with your screwdriver. Take the panel off the cabinet and set it aside.
Step 4. Loosen the bolts holding the top panel to the cabinet. Slide the panel backwards, then lift it off the assembly.
Step 5. Use your screwdriver to remove the screws at the bottom of the lower front access panel. Take the panel off your machine and set it aside.
Step 6. Open your washing machine’s door. Using either a pair of needle-nosed pliers or a flat-blade screwdriver, pry the retaining wire off the door boot seal. Peel the door seal off the opening.
Step 7. Untwist the wire retainer holding the door boot seal to the inlet port inside the machine. Push a 1/2 inch socket onto the pointed ends of the upper mounting pins holding the shock absorbers to the tub.
Step 8. Use a pair of pliers to pull the mounting pins out of the tub, then set them aside. Push the two shock absorbers out of the mounts, then set them aside.
Step 9. Release the air pressure tube from the retainer at the side of the tub using a pair of pliers.
Step 10. Rotate the drive belt an remove it from the drive pulley and motor pulley. Unplug the wire connector attached to the motor assembly, then cut the zip-tie holding the wires to the tub.
Step 11. With a 5/16 inch nut-driver, loosen the bolts holding the motor assembly to the bottom of the tub. Carefully pull the motor out of the cabinet, then set it aside.
Step 12. Use your screwdriver to loosen the screw-clamp holding the sump hose to the bottom of the tub.
Step 13. Pull the hose off the tub (some water may spill out so keep a rag nearby). Pull the vent tube off the port at the top of the tub.
Step 14. Use a socket wrench to loosen the bolts holding the counter-weight to the back of the tub. Carefully lift the weight off the assembly and set it aside.
Step 15. Loosen the screws holding the motor control board to the cabinet. Pull the board off the cabinet, then unplug each electrical connector attached to the board (ensure that you take note of where each connector goes).
Step 16. Remove the screws holding the spring retaining straps to the top of the cabinet, then take the straps off.
Step 17. Lift the two suspension springs off the cabinet, then carefully lower the tub assembly (get someone to help you if needed). Guide the tub assembly out of the cabinet.
Step 18. Unhook the two suspension springs from the tub. Turn the tub upwards. Using a 3/8 inch socket wrench, loosen the bolts holding the two halves of the outer tub together.
Step 19. Lift the front half of the outer tub off the assembly and set it aside. Turn the tub assembly over.
Step 20. Using a 9/16 inch socket, take out the bolt holding the drive pulley to the back of the tub. Take the pulley wheel off and set it aside.
Step 21. Lift the rear half of the outer tub off the inner tub. Remove your new washing machine outer tub from its packaging.
Step 22. Transfer the bolts and counter-weight plates from the old drum to the new one. Lower the rear half of the outer tub onto the inner tub.
Step 23. Put the drive pulley on the shaft, then apply the bolt using your socket wrench. Turn the tub assembly over and put the front half back on. Use your 3/8 inch socket wrench to apply the bolts.
Step 24. Hook the two suspension springs onto the tub assembly. Carefully guide the tub back into the cabinet.
Step 25. Lift the two suspension springs and hook them onto the cabinet. Push the two shock absorbers into the mounts at the bottom of the tub. Push the mounting pins into place to secure the shock absorbers.
Step 26. Put the suspension spring retaining straps back on, then apply the screws with your screwdriver. Reattach the vent tube to the port at the top of the tub,
Step 27. Plug each electrical connector into its appropriate terminal on the motor control board. Install the board in the cabinet, then apply the screws to secure it.
Step 28. Mount the counter-weight onto the tub, then use your socket wrench to apply the bolts.
Step 29. Reconnect the sump hose to the port at the bottom of the tub, then tighten the screw-clamp to secure it.
Step 30. Carefully mount the drive motor at the bottom of the tub, then apply the nuts with your socket wrench. Plug the electrical connector to the motor, then secure the wire the retainer.
Step 31. With the grooved side turned inwards, loop the drive belt around the drive pulley and motor pulley.
Step 31. Push the air pressure dome back into the retainer at the side of the tub. Fit the door boot seal back around the water inlet port, then secure it by tightening the screw-clamp.
Step 32. Fit the door gasket around the front panel. Fit the retaining wire around the door gasket using a flat-blade screwdriver.
Step 33. Snap the lower front access panel onto the cabinet, then use your screwdriver to apply the screws at the bottom.
Step 34. Place the top panel on the cabinet, then apply the screws to secure it. Mount the rear panel on the cabinet, then secure it with the screws.
Step 35. Reattach the COLD and HOT water supply hoses to the ports at the back of the machine (ensure that the hoses are secured properly in order to prevent water leaks).
Step 36. Plug your washing machine’s power cord into the electrical outlet, then turn the water supply faucet on. To ensure that the problem has been fixed, try running a spin cycle.
Electrolux Washing Machine Error Code E60 — Solved
The E60 error code indicates that your machine is having trouble heating water. To fix this issue, you’ll need to replace the heating element. Take the following steps to do this…
Step 1. Unplug your washing machine’s power cord from the electrical outlet before starting this repair in order to prevent electrocution.
Step 2. With a Philips screwdriver, loosen the screws holding the rear panel to the cabinet. Pull the panel off the machine and set it aside.
Step 3. Unplug the electrical connectors from the heating element at the bottom of the tub (make sure to take note of where each connector goes).
Step 4. Loosen the bolt holding the heating element using a 10mm socket wrench. Pry the heating element out of the housing using a flat-blade screwdriver, then discard it.
Step 5. Prepare your new washing machine heating element for installation by removing it from its packaging.
Step 6. Slide the new heating element into the housing at the bottom of the tub, then secure it by applying the bolt with your 10mm socket wrench.
Step 7. Plug each wire connector into its appropriate terminal on the new heating element.
Step 8. Place the rear panel on the cabinet, then use your Philips screwdriver to apply the screws.
Step 9. Plug your washing machine’s power cord back into the electrical outlet, then try running a wash cycle to ensure that the problem has been fixed.
Electrolux Washing Machine Error Code E90 — Solution
The E90 error code in your Electrolux washing machine indicates an issue with the control board. To replace the control board in your washing machine, take the following steps…
Step 1. Disconnect your washing machine’s power cord from the electrical outlet in order to prevent electrocution.
Step 2. With a Philips screwdriver, loosen the bolts at the back of the machine holding the top panel to the cabinet. Pull the top panel backwards a bit, then lift it off the machine.
Step 3. Open the door of your washing machine. Pry the retaining wire off the door gasket using a flat-blade screwdriver (take care not to puncture the gasket).
Step 4. Peel the door gasket off the front panel. Slide the detergent tray out, then press the tab to release from the dispenser.
Step 5. Tip the machine backward, then place a support under the front panel (get someone to help if needed). With your Philips screwdriver, loosen the four screws at the bottom of the front panel.
Step 6. Set your washing machine back on its feet. Use your Philips screwdriver to take out the bolts at the top of the panel, and the screws next to the detergent dispenser.
Step 7. Carefully lift the front panel off the cabinet, then disconnect the wire harnesses attached to it.
Step 8. Set the front panel face-down on the floor. Use a flat-blade screwdriver to detach the ribbon connector from the control board.
Step 9. Use your Philips screwdriver to take out the five screws holding the user interface control board to the front panel. Lift the board off the panel, then discard it.
Step 10. Remove your new washing machine user interface control board from its packaging.
Step 11. Mount the new board on the panel, then apply the screws using your Philips screwdriver. Connect the ribbon connector of the new control board.
Step 12. Lift the front panel and connect the electrical connectors. Mount the panel on the cabinet, then apply the screws at the top of the panel.
Step 13. Tip your machine backwards, then apply the four screws at the bottom of the panel. Set your machine upright.
Step 14. Fit the door gasket around the front panel, the use a flat-blade screwdriver to fit the retaining band. Slide the soap tray into the dispenser.
Step 15. Place the top panel on the cabinet, then apply the screws at the back using a Philips screwdriver. Plug your machine into the electrical outlet, then try running a cycle to see if the issue has been resolved.