If you are getting various Maytag washing machine error codes, you’ve come to the right place. In this detailed guide, we’ll be explaining the meanings of these codes and giving you steps on how to fix them…
Table of Contents
Maytag Washing Machine Error Code F02 — Quick Fix
The F02 Maytag washing machine error code indicates that the machine is taking too long to drain. Here are the causes of this issue…
1. Clogged Pump Filter (Front Loaders Only)
If your Maytag washing machine doesn’t drain, it could be that the pump filter is clogged. Front loaders usually have a trap door at the lower front section. Under this door, you’ll find the pump filter knob. To fix the drainage issue, you’ll need to turn the pump filter knob and clean out any debris that may have accumulated.
2. Failed Drain Pump
Another thing that can prevent your Maytag washing machine from draining is a damaged pump. To replace the pump in your washer, follow the steps below…
Front Loaders
Take the following steps to replace the drain pump assembly in your Maytag front loader washing machine…
Step 1. Disconnect your appliance from the electrical outlet before starting this procedure in order to prevent electrocution.
Step 2. Use a 1/4 inch socket wrench to loosen the three bolts holding the lower front access panel to the cabinet. Take the panel off the machine and set it aside.
Step 3. Place a container underneath the pump filter. Turn the filter knob, then let any water stuck in the machine drain out.
Step 4. Once all the water has drained out, put the pump filter back in place. Using pliers, release the spring clamps holding the sump hose and outlet hose to the pump.
Step 5. Pull each hose off the drain pump (ensure that you keep a rag nearby to clean any water leaks).
Step 6. Pry the cap off the pump assembly, then unplug the wire connector from the terminal. Using your 1/4 inch nut-driver, loosen the bolts holding the drain pump assembly to the bottom of the cabinet.
Step 7. Pull the drain pump out of the machine, then discard it. Prepare the new pump for installation by taking it out of its packaging.
Step 8. Install the new pump in the cabinet, then tighten the bolts using your nut-driver.
Step 9. Pry the cap off the new pump, then plug the wire connector in. Connect each hose to its appropriate port on the new drain pump. Secure the pump by sliding the retaining clamp into place using pliers.
Step 10. Mount the lower access plate back on the cabinet. Secure the panel by tightening the bolts with your nut-driver.
Step 11. Reconnect your appliance to the electrical outlet, then try running a wash cycle to see if the washer has started draining.
Top Loaders
Take the following steps to replace the pump assembly in your top loader Maytag washing machine…
Step 1. In order to prevent water leaks or electrocution, be sure to disconnect your washer from the outlet and turn the water faucets off before starting this repair.
Step 2. Go to the back of the washing machine, then use pliers to disconnect the HOT and COLD water hoses from the inlet ports (some water may spill out, so it is advised that you keep a rag nearby).
Step 3. With a pair of pliers, press the retaining clamp holding the main drain hose to the back of the cabinet, then slide it out of place. Disconnect the hose from the machine.
Step 4. Get someone to help you tip your washing machine backwards, then lay it on the floor. Using a 5/16 inch socket wrench, take out the three bolts holding the drain pump to the bottom of the tub.
Step 5. Unplug the wire harness attached to the pump assembly. Using your pliers, release the clamps holding the two outlet hoses to the drain pump.
Step 6. Pull each hose off the pump (make sure to keep a rag nearby to clean any leaks).
Step 7. Discard the old pump, then prepare the new one for installation by taking it out of its packaging.
Step 8. Mount the new drain pump onto the bottom of the tub, then secure it by applying the bolts with your 5/16 inch nut-driver.
Step 9. Plug the wire connector into the pump. Connect each of the outlet hoses to their appropriate ports on the pump assembly. Use your pliers to slide the spring clamp into place.
Step 10. Carefully lift your washing machine back onto its feet. Reconnect the main drain hose to the port at the back of the cabinet, then use the spring clamp to secure it.
Step 11. Reconnect the two water supply hoses to the inlet ports (ensure that the hoses are properly secured so water doesn’t leak).
Step 12. Turn the water faucets on, then plug your washer’s power cord back into the outlet. Make sure the problem has been fixed by running a wash cycle.
Maytag Washing Machine Error Code F03 — How To Fix
The F03 Maytag washing machine error code indicates that the machine can’t detect the level of the water. The following are the causes of this issue…
1. Damaged Water Pressure Sensor
Replace the water pressure sensor in your Maytag washing machine with the following steps…
Step 1. Ensure that your washing machine is disconnected from the electrical outlet before starting this repair in order to prevent electrocution.
Step 2. Loosen the screws at the back of the cabinet securing the top panel using a 1/4 inch nut-driver. Slide the panel backwards and lift it off the machine.
Step 3. Reach underneath the pressure sensor at the side of the cabinet, then pull the pressure hose off.
Step 4. Unplug the connector attached to the sensor. Rotate the pressure sensor a bit, then take it off the cabinet. Discard the old sensor, then take the new one out of its packaging.
Step 5. Snap the new pressure sensor onto the cabinet, then rotate it to secure. Plug the connector into the terminal on the new switch.
Step 6. Connect the pressure hose to the port at the bottom of the sensor. Place the top panel assembly on the cabinet. Secure the panel by tightening the screws at the back using your screwdriver.
Step 7. Reconnect your washing machine to the electrical outlet, then ensure that the error code has cleared by running a wash cycle.
Note: The steps above are only applicable to Maytag front loader washing machines.
2. Damaged Pressure Sensor Tube
Follow the steps below to replace the pressure sensor tube in your Maytag washing machine…
Front Loaders
Take the following steps to replace the pressure tube in your Maytag front loader washing machine…
Step 1. In order to prevent any chances of electrical damage, make sure to disconnect your appliance from the power outlet before starting this repair.
Step 2. With a 1/4 inch socket wrench, loosen the screws at the back of the washing machine holding the top panel. Slide the panel backwards about an inch or so, then lift it off the machine.
Step 3. Using your socket wrench, loosen the bolts holding the rear panel to the cabinet. Lift the panel off the machine and set it aside.
Step 4. With a flat-blade screwdriver, pry the pressure hose off the air dome at the lower rear of the tub.
Step 5. Release the pressure hose from the retainers at the back of the tub. Pull the tube off the port on the water pressure sensor.
Step 6. Take the tube out of the cabinet, then discard it. Prepare the new hose for installation by taking it out of its packaging.
Step 7. Connect one end of the new hose to the port on the air dome. Secure the tube in the retainers at the back of the tub.
Step 8. Connect the other end of the new tube to the water pressure sensor. Mount the rear panel back on the cabinet, then secure it by applying the bolts with your 1/4 inch nut-driver.
Step 9. Place the top panel on the machine, then push it forwards. Secure the panel by applying the bolts with your 1/4 inch socket.
Step 10. Plug your washing machine’s power cord back into the electrical outlet. Make sure the error code is gone by running a wash cycle.
Top Loaders
Replace the pressure switch tube in your top loader Maytag washing machine with the following steps…
Step 1. In order to prevent any chances of electrical damage, make sure to unplug your washing machine’s power cord from the outlet before starting this repair.
Step 2. Using a 1/4 inch nut-driver, loosen all the bolts holding the rear panel to the cabinet. Lift the panel off and set it aside.
Step 3. With your nut-driver, take out the three bolts at the back of the machine holding the control panel. Lift the panel out of place, then set it face-down on the cabinet
Step 4. Use the nut-driver to loosen the bolt holding the little panel above the wiring and tube retainer.
Step 5. Take out the bolt holding the drain hose retainer to the back of the cabinet. Move the retainer out of place. Pull the pressure switch hose off the port on the control board.
Step 6. Carefully cut the pieces of tape holding the pressure tube to the wires. With a flat-blade screwdriver, release the retaining clamp securing the tube and wires.
Step 7. Pull the pressure tube out of the retainers at the side of the tub. Disconnect the other end of the pressure tube from the port on the outer tub.
Step 8. Discard the old hose, then take the new one out of its packaging. Connect one end of the new hose to the port on the control board.
Step 9. Secure the new pressure hose in the retainers at the side of the machine, then connect the other end to the port at the side of the tub.
Step 10. Use the retaining clamp to secure the new hose and wires. Using some electrical tape, tape the pressure tube and wires together.
Step 11. Lift the control panel assembly, then snap it back onto the cabinet. Secure the panel by applying the bolts with your 1/4 inch nut-driver.
Step 12. Remount the little plate on the rear panel, then use your nut-driver to apply the nuts. Put the drain hose retainer back on the machine. Apply the bolts to secure the panel.
Step 13. Mount the main rear access panel on the cabinet, then use your 1/4 inch nut-driver to apply the screws.
Step 14. Plug your washing machine’s power cord into the electrical outlet, then try running a wash cycle to ensure that the error code is gone.
Check out these other articles…
Whirlpool Washing Machine Smells [Proven Solutions]
Maytag Washing Machine Bearings [Problems, Solutions & Guide]
Maytag Washing Machine Belt [Problems, Solutions & Guide]
Maytag Washing Machine Actuator [Problems, Solutions & Guide]
Maytag Washing Machine Agitator [Problems, Solutions & Guide]
Maytag Washing Machine Error Code F5 — Solved
The F5 Maytag washing machine error code indicates that the door isn’t locking. Ensure that you firmly shut the door of your washer before starting a cycle. If your washing machine door still isn’t locking, you’ll need to replace the lock assembly. The steps below show you how to do this…
Front Loaders
Take the following steps to replace the door lock in your front loader Maytag washing machine…
Step 1. Disconnect your washer’s power cord from the outlet in order to avoid electrical damage.
Step 2. Open your washing machine’s door. With a Torx-20 screwdriver, loosen the bolts holding the door lock assembly.
Step 3. Insert a flat-blade screwdriver underneath the metal wire around the door gasket, then work it around until the wire pops off (take care not to damage the seal).
Step 4. Peel the door boot seal off the front panel. Reach behind the front panel and pull the door lock out of place. Unplug the wire connector attached to the lock assembly.
Step 5. Discard the old door lock, then take the new one out of its packaging. Plug the wire connector into the new door lock assembly.
Step 6. Install the lock in the cabinet, then secure it by applying the bolts with your Torx screwdriver.
Step 7. Carefully refit the door boot seal around the front panel. Using a flat-blade screwdriver, fit the retaining wire around the gasket.
Step 8. Plug your appliance back into the electrical outlet, then ensure that everything works properly by running a cycle.
Top Loaders
To replace the lid lock in your top loader Maytag washing machine, follow the steps below…
Step 1. Disconnect your washing machine from the electrical outlet before starting this repair in order to prevent electrocution.
Step 2. Using a 1/4 inch nut-driver, take out the three screws at the back of the machine holding the control panel.
Step 3. Use your nut-driver to take out the bolt holding the little access plate above the drain hose retainer. Lift the control panel, then set it face-down on the cabinet.
Step 4. Unplug the control panel’s wire connector from the main control board. Set the panel aside.
Step 5. Unplug the lid switch wire connector from the control board. Pass the lid switch wire and connector through the opening at the back of the cabinet.
Step 6. Place some tape on the lid of your washing machine to help secure it. Insert a putty knife under the two front corners of the top panel (this will release the locking clips).
Step 7. Lift the top panel and support it by placing it against a wall, or using a lanyard. Using a flat-blade screwdriver, release the lid lock wire from the retainers at the bottom of the front panel.
Step 8. With a 1/4 inch nut-driver, loosen the bolts holding the lid lock to the bottom of the front panel. Take the lid switch off the panel, then set it aside.
Step 9. Take your new lid switch out of its packaging, then mount it on the top panel. Secure the switch by applying the nuts with your 1/4 inch socket.
Step 10. Snap the lid switch wire into the retainers at the bottom of the top panel. Pass the lid switch wire and connector through the opening on the top panel.
Step 11. Lower the top panel and snap it back onto the cabinet. Plug the lid switch wire into the main control board.
Step 12. Plug the control panel’s wire connector back in. Lift the panel and snap it onto the cabinet. Secure the control panel by applying the three screws with your nut-driver.
Step 13. Put the little access plate back onto the rear of the cabinet, then apply the screw to secure. Plug your appliance into the electrical outlet, then try running a wash cycle to ensure that everything works properly.
Maytag Washing Machine Error Code F06 — Solution
The F06 Maytag washing machine error code indicates that there is a communication issue between the main control board and motor control board. To replace the motor control board in your washer, follow the steps below…
Step 1. Make sure to unplug your washing machine’s power cord from the electrical outlet before starting this repair in order to prevent any chances of electrocution.
Step 2. Using a 1/4 inch nut-driver, take out the three screws at the bottom of the lower front access panel. Lift the panel off the machine and set it aside.
Step 3. The motor control board will be mounted at the left side of the cabinet. In order to access the board, you’ll need to take the left shock absorber out. Use pliers to grab the top of the shock absorber, rotate it, then pull it out of the tub.
Step 4. Wedge a flat-blade screwdriver underneath the motor control board to release the retaining tabs.
Step 5. Pry the cap off the motor control board (use a flat-blade screwdriver if needed). Unplug the wire connectors attached to the board (ensure that you note where each connector goes).
Step 6. Using a flat-blade screwdriver, pry the wire retainer out of the slot on the motor control board.
Step 7. Pull the motor control board out of the cabinet, then discard it. Take your new washing machine motor control board out of its packaging.
Step 8. Snap the wire retainer into the slot on the new motor control board. Snao the new board into the slots on the cabinet.
Step 9. Pry the cap off the new board, then plug each wire connector into its appropriate terminal.
Step 10. Snap the cap back onto the board. Grab the top of the left shock absorber, then push it into the mount at the bottom of the tub.
Step 11. Snap the lower front access panel back onto the machine, then use your 1/4 inch nut-driver to apply the bolts at the bottom.
Step 12. Reconnect your washing machine to the electrical outlet, then try running a wash cycle to see if the error code is gone.
Maytag Washing Machine Error Code F0E7 — Solved
The F0E7 Maytag washing machine error code indicates that clothes were detected in the drum during the washer’s cleaning cycle. To fix this issue, turn your washer off, then take out any clothes in the drum. Plug your machine back into the outlet, then let it complete the cycle.
Maytag Washing Machine Error Code F51 — How To Fix
The F51 Maytag washing machine error code indicates that the rotor position sensor is damaged. To replace this part, follow the steps below…
Step 1. Ensure that you turn off your washing machine’s water supply taps and disconnect the power cord from the electrical outlet before starting this repair in order to prevent leaks or electrocution.
Step 2. Using a pair of pliers, disconnect the water inlet hoses from the ports at the back of the washer (we recommend keeping a rag nearby to clean up any leaks).
Step 3. Pull your washing machine’s drain hose out of the home drain. Place some tape on the lid of your washer to help secure it.
Step 4. Get someone to help you tip your washing machine forwards carefully, then set it on the floor.
Step 5. With a 1/4 inch Allen wrench, loosen the bolt holding the rotor assembly to the bottom of the tub. Carefully pry the rotor off the machine and set it aside.
Step 6. Using a 3/8 inch socket wrench, loosen the bolts holding the stator assembly to the bottom of the tub. Lift the stator and shield off the tub.
Step 7. Unplug the power connector from the stator. Pry the rotor position sensor off the stator using a flat-blade screwdriver. Set the stator aside.
Step 8. Unplug the wire connector from the sensor, then detach the wire retaining clip. Note the positioning of the stator wires connected to the drain and re-circulation pumps, then unplug them.
Step 9. Pull the wire retainers off the slots at the bottom of the tub. With a 1/4 inch nut-driver, take out the bolts holding the rear access panel to the cabinet. Lift the panel off the washer and set it aside.
Step 10. Unplug the water level pressure hose from the port at the side of the outer tub. Pull the tube out of the retainers.
Step 11. With a pair of needle-nosed pliers, release the wire harness retaining clip off the hose bracket. Using your nut-driver, take out the screws holding the drain hose retaining panel to the back of the machine.
Step 12. Pull the wire retainers off the hose retaining panel. Using your nut-driver, take out the bolts holding the wire cover plate. Take the plate off the machine and set it aside.
Step 13. With the 1/4 inch nut-driver, take out the three screws holding the control panel assembly to the top of the cabinet. Lift the panel off, then unplug the wire connector from the main control board.
Step 14. Release any zip-ties holding the wires. Pull the water level pressure hose from the port on the control board.
Step 15. Note the positioning of the connectors attached to the main control board, then disconnect each one. Pull the wiring and tube assembly out of the cabinet, then discard.
Step 16. Unpack your new rotor position sensor kit. Plug the wire connectors into the appropriate terminals on the control board.
Step 17. Connect the new water level pressure hose to the port on the board. Secure the wires and hose using a zip-tie.
Step 18. Snap the wire and tube retainers into the drain hose retaining plate. Put the wire cover plate back on the machine, then use your 1/4 inch nut-driver to apply the bolt.
Step 19. Move the drain hose retaining plate back on the cabinet, then tighten the bolts with your nut-driver.
Step 20. Snap the new water level pressure tube in the retainers. Connect the tube to the port at the side of the tub.
Step 21. Route the new wires under the drain pump inlet hose. Push the wire retainers into the slots at the bottom of the tub.
Step 22. Plug the sensor wire connector to the new sensor. Plug the wires to their appropriate terminals on the drain and re-circulation pumps.
Step 23. Plug the power connector back to the stator assembly. Snap the new rotor position sensor onto the stator.
Step 24. Place the stator and mounting plate at the bottom of the tub, then apply the mounting bolts using your 3/8 inch nut-driver.
Step 25. Place the rotor on the stator. Using your 1/4 inch Allen wrench, tighten the bolt to secure the rotor.
Step 26. Remount the rear access panel on the cabinet. With the 1/4 inch nut-driver, apply the bolts to secure the panel.
Step 27. Reconnect the control panel’s wire connector to the control board. Snap the panel onto the cabinet, then apply the three bolts using your 1/4 inch nut-driver.
Step 28. Carefully lift your washing machine back onto its feet and peel the tape off the lid.
Step 29. Reinsert the drain hose into the home drain. Reconnect the HOT and COLD water inlet hoses to the ports at the back of the machine (ensure that the hoses are properly connected in order to prevent leaks).
Step 30. Turn your washing machine’s water supply faucets on, then plug the power cord into the electrical outlet. Ensure that the issue has been fixed by running a cycle.
Maytag Washing Machine Error Code NF — Solved
The NF Maytag washing machine error code indicates that the drum isn’t filling with water. Here are the causes of this issue…
1. Water Faucets Are Off
If your washing machine isn’t filling with water, the first thing you should do is check to ensure that the faucets are fully opened. Also ensure that the water hoses aren’t bent or kinked in any way, as this could restrict water flow.
2. Clogged Inlet Filters
Your washing machine has two inlet filters in the ports at the back of the machine. Over time, dirt from your water supply can accumulate in the filter and clog it. To fix this issue, you’ll need to disconnect the inlet hoses and use needle-nosed pliers to take the filters out. You can rinse the filters using a running water and a soft brush.
3. Water Inlet Valves Are Damaged
The inlet valves control the quantity of water that flows into the drum. If this part gets damaged, you washer can overfill or not fill at all. Follow the steps below to replace this part…
Front Loaders
Take the following steps to replace the water inlet valve in your front loader Maytag washing machine…
Step 1. In order to avoid electrical damage or water leaks, it is advised that you turn your water faucets off and disconnect the power cord from the outlet before starting this repair.
Step 2. Using pliers if needed, disconnect the water inlet hoses from the ports at the back of the machine (ensure that you keep a rag nearby to clean any leaks).
Step 3. Loosen the three bolts at the back of the machine securing the top panel using a 1/4 inch nut-driver. Slide the panel backwards, then lift it off the machine.
Step 4. Note the positioning of the connectors attached to the inlet valve assembly, then disconnect each one.
Step 5. Using your pliers, release the spring clamps holding the inlet valve hoses to the dispenser, then slide them out of place. Pull each hose off the dispenser.
Step 6. With a Torx screwdriver, loosen the bolts holding the inlet valve assembly to the cabinet. Pull the inlet valve out of the machine, then discard it.
Step 7. Take your new washing machine water inlet valve out of its packaging. Install the new valve in the cabinet, then use your Torx screwdriver to apply the bolts.
Step 8. Connect each of the inlet valve hoses to the ports on the dispenser. Secure the hoses by sliding the spring clamps into place with pliers.
Step 9. Plug each wire connector into its appropriate terminal on the new inlet valve assembly.
Step 10. Remount the top panel on the cabinet, then push it forwards. With your 1/4 inch nut-driver, apply the bolts at the back of the machine to secure the panel.
Step 11. Reconnect the COLD and HOT water inlet hoses to their appropriate ports at the back of the cabinet (in order to prevent leaks, make sure the hoses are secured properly).
Step 12. Plug your machine back into the electrical outlet, then turn the water faucets back on. To ensure that the issue has been fixed, try running a wash cycle.
Top Loaders
Take the following steps to replace the inlet valve assembly in your top loader Whirlpool washing machine…
Step 1. Prevent water leaks and electrocution by unplugging your washing machine’s power cord from the outlet and turning the water taps off before starting this repair.
Step 2. Place some tape on the lid of your washing machine to help secure it. Insert a putty knife underneath the front corners of the top panel in order to release the locking clips. Lift the top panel, then support it by placing it against a wall, or using a lanyard.
Step 3. Using pliers, release the spring clamps holding the inlet hoses to the ports at the bottom of the top panel. Pull each hose off the ports (water may spill, so keep a rag nearby).
Step 4. Carefully lower the top panel back onto the cabinet. Go to the back of the machine, then use your pliers to disconnect the COLD and HOT water supply hoses from the ports.
Step 5. Loosen the three bolts holding the control panel assembly to the cabinet using a 1/4 inch nut-driver. Lift the control panel assembly and set it face-down on top of the cabinet.
Step 6. Note the positioning of the wire connectors attached to the water inlet valve, then unplug each one.
Step 7. Loosen the bolts securing the inlet valve to the cabinet using a 1/4 inch nut-driver. Take the valve off the machine, then discard it.
Step 8. Prepare your new washing machine water inlet valve for installation by taking it out of its packaging.
Step 9. Place the new inlet valve on the cabinet, then secure it by applying the bolts with your 1/4 inch socket.
Step 10. Plug the wire connectors into the appropriate terminals on the valve. Lift the control panel and snap it back on the cabinet. Secure the panel by applying the screws with your nut-driver.
Step 11. Lift the top panel assembly and support it. Reconnect the inlet hoses to their corresponding ports at the bottom of the top panel, then slide the retaining clamps into place to secure them.
Step 12. Lower the top panel and snap it back onto the cabinet. Peel the tape off the lid of your machine.
Step 13. Reconnect the HOT and COLD water inlet hoses to the ports at the back of the machine. Turn the water faucets back on, then plug the power cord into the electrical outlet. Ensure that everything works properly by running a wash cycle.