If you are having issues with your Maytag washing machine filter, you’ve come to the right place. This detailed guide gives you steps how to deal with these issues…
Table of Contents
How To Clean Maytag Washing Machine Filter — Solved
The steps below show you how to clean your Maytag washing machine filters…
Water Inlet Filters
Take the following steps to clean the inlet filter in your Maytag washing machine…
Step 1. Turn your washing machine’s water supply taps off before starting this repair in order to prevent water leaks.
Step 2. Spread a towel on the floor underneath the water inlet hoses to catch any leaks. Using pliers if needed, disconnect the inlet hoses from the ports at the back of the washer.
Step 3. Use needle-nosed pliers to pull out the inlet filters from the ports on your washer. Take the filters to a sink, then clean out any debris that may be clogging it.
Step 4. Once the filters are clean, push them back into the ports. Reconnect the water inlet hoses to the appropriate ports on the machine. Turn the water taps back on.
Drain Pump Filter
Follow the steps below to clean the drain pump filter in your front loader Maytag washing machine…
Step 1. In order to prevent electrical damage, ensure that your washing machine is unplugged from the outlet before starting this repair.
Step 2. Using a 1/4 inch nut-driver, loosen the three bolts holding the lower front access panel to the cabinet. Take the panel off the machine and set it aside.
Step 3. Spread a towel on the floor in front of the machine. Place a container underneath the pump filter.
Step 4. Turn the pump filter knob, then let any water stuck in the machine drain out. Take the filter to a sink, then clean out any lint and debris that may be clogging it.
Step 5. Once the filter is clean, put it back in the housing. Snap the lower front access panel back onto the cabinet, then secure it by applying the three bolts with your 1/4 inch nut-driver. Plug your machine back into the outlet.
Check out these other articles…
Whirlpool Washing Machine Smells [Proven Solutions]
Maytag Washing Machine Bearings [Problems, Solutions & Guide]
Maytag Washing Machine Belt [Problems, Solutions & Guide]
Maytag Washing Machine Actuator [Problems, Solutions & Guide]
Maytag Washing Machine Error Codes [Proven Solutions]
Maytag Washing Machine Filter Stuck — How To Fix
If your Maytag washing machine filter is stuck, it indicates that an item has jammed it. To fix this issue, you’ll need to clean out the pump. Follow the steps below to do this…
Step 1. Avoid electrical damage by unplugging your washing machine from the outlet before starting this repair.
Step 2. Take out the screws holding the lower front access panel to the cabinet using a 1/4 inch nut-driver. Pry the panel off the machine and set it aside.
Step 3. Pry the cap off the drain pump assembly, then unplug the wire connector from the pump.
Step 4. Using pliers, release the spring clamps holding the two outlet hoses to the pump, then slide them out of place.
Step 5. Pull each hose off the drain pump (make sure to keep a rag nearby to clean any leaks).]
Step 6. Using your 1/4 inch socket wrench, loosen the bolts holding the pump to the cabinet. Pull the drain pump out of the cabinet.
Step 7. Insert a pair of needle-nosed pliers into the ports of the drain pump, then try taking out any pieces of debris that may be clogging the pump.
Step 8. Once you’ve cleaned the pump, try turning the pump filter cover to ensure that the issue has been fixed.
Step 9. Reinstall the drain pump assembly in the cabinet, then secure it by applying the bolts using your 1/4 inch nut-driver.
Step 10. Plug the wire connector back into the drain pump terminal. Reconnect the two outlet hoses to their corresponding ports on the pump, then use pliers to move the retaining clamp into place.
Step 11. Snap the lower front access panel onto the cabinet, then tighten the bolts with your nut-driver. Plug your appliance back into the electrical outlet.
How To Replace Maytag Washing Machine Filter — Quick Fix
Follow the steps below to replace your Maytag washing machine filters…
Agitator Filter
To replace the agitator filter, here’s what you’ll need to do: open the lid of your washing machine, then use a flat-blade screwdriver to pry the cap off the agitator. Pull the filter out of the agitator, then discard it. Take your new agitator filter out of its packaging, then push it into place. Snap the cap back onto the agitator, then close your washer’s lid.
Water Inlet Filter
Follow the steps below to replace the water inlet filters in your Maytag washing machine…
Step 1. Make sure the water faucets are turned off before starting this repair in order to prevent water leakage.
Step 2. Disconnect the water supply hoses from the ports at the back of your washing machine.
Step 3. Pull the old inlet filters out of the ports using pliers, then discard them. Take your new washing machine water inlet filters out of their packaging.
Step 4. Push the new inlet filters into the ports at the back of the machine. Reconnect the water supply hoses to the ports on the machine. Turn your washer’s water supply faucets back on.
Drain Pump Filter
Follow the steps below to replace the pump filter in your Maytag washing machine…
Step 1. Ensure that your washing machine is disconnected from the outlet before starting this repair in order to prevent electrocution.
Step 2. With a 1/4 inch nut-driver, remove the three bolts at the bottom of the lower front access panel. Lift the panel off the machine and set it aside.
Step 3. Rotate the pump filter knob, then take it out of the housing. Discard the old filter, then take the new one out of its packaging.
Step 4. Install the new pump filter in the machine, then secure it. Snap the lower access panel onto the machine, then secure it by applying the three bolts. Plug your washing machine back into the electrical outlet.