If your Asko washing machine is not filling with water, there are various possible causes. This detailed guide lists the causes of this issue, and provides steps to deal with them…
Table of Contents
Asko Washing Machine Is Not Filling With Water — How To Fix
If your Asko washing machine is not filling with water, the following are causes to look for…
1. Water Taps Are Off
The first thing to check if your Asko washing machine is not filling, is the water supply. Ensure that the water supply taps are fully opened before starting a cycle.
2. Low Water Pressure
if your Asko washing machine is not filling, it could be due to low water pressure. If the pressure of your water supply is below 20 psi, your machine won’t fill properly. To fix issues with water pressure, you’ll need to contact a plumber.
3. Clogged Inlet Filters
If your Asko washing machine is not filling with water, it could be due to clogged inlet filters. Follow the steps below to clean the inlet filters…
Step 1. In order to prevent any chances of electrocution, it is advised that you disconnect your machine from the power outlet before starting this repair.
Step 2. Turn the water supply taps off in order to prevent leakage. Using a pair of pliers if needed, disconnect the COLD and HOT water supply hoses from the ports at the back of the machine.
Step 3. Use a pair of needle-nosed pliers, pull the inlet filters out of the ports at the back of the machine.
Step 4. Take the filters to a sink, then clean out any dirt that may have accumulated in them.
Step 5. Once the filters are clean, push them back into the ports. Reconnect the COLD and HOT water supply hoses to the back of the machine (in order to prevent leaks, ensure that the hoses are properly attached).
Step 6. Turn the water supply faucets back on, then plug your washing machine’s power cord into the outlet. Try running a wash cycle to ensure that the issue has been fixed.
4. Damaged Water Inlet Valve
The inlet valve controls the flow of water into the machine. If your Asko washing machine is not filling, the valve could have failed. Follow the steps below to replace this part…
Step 1. Prevent any chances of electrocution by disconnecting your appliance from the outlet. Turn the water taps off to prevent leakage.
Step 2. Use pliers to disconnect the inlet hose from the port at the back of the machine (keep a rag nearby in case water spills).
Step 3. Loosen the bolts at the back of the machine securing the top panel using a Torx screwdriver.
Step 4. Slide the top panel backwards a few inches, then lift it off the machine. Disconnect the wire harnesses from the inlet valve mounted on the cabinet.
Step 5. Using your Torx screwriver, take out the bolts holding the valve assembly to the cabinet.
Step 6. Pull the valve assembly out of the cabinet. Use pliers to release the retaining clamps securing the outlet hoses to the valve. Discard the old inlet valve, then prepare the new one for installation by unpacking it.
Step 7. Connect the outlet hoses to the ports on the new valve assembly. Secure the hoses by sliding the clamps into place.
Step 8. Mount the inlet valve on the cabinet, then tighten the bolts using your Torx screwdriver. Plug the wire harnesses into the new valve.
Step 9. Mount the top panel on the cabinet, then push it forwards. Apply the bolts at the back of the machine to secure the panel.
Step 10. Attach the water supply hose to the port at the back of the cabinet (ensure that the hose is properly connected, in order to prevent leaks)
Step 11. Turn the water supply faucet back on, then plug the power cord into the outlet. To ensure that the issue has been fixed, try running a wash cycle.
Check out these other articles…
KitchenAid Washing Machine Door [6 Issues & Proven Solutions]
KitchenAid Washing Machine Filter [3 Issues & Quick Solutions]
KitchenAid Washing Machine Is Stuck On Rinse [4 Causes & Quick Solutions]
KitchenAid Washing Machine Is Making Noise [8 Causes & Proven Solutions]
Asko Washing Machine Will Not Drain [2 Causes & Quick Solutions]
Zanussi Washing Machine Bearings [Issues & Proven Solutions]
Zanussi Washing Machine Is Not Draining [2 Problems & Quick Solutions]
5. Failed Water Pressure Switch
The pressure switch monitor’s the water level and tells the valve when to shut off. If your Asko washing machine is not filling, the pressure switch may have failed. Follow the steps below to replace this part…
Step 1. In order to avoid electrocution, ensure that your machine is disconnected from the power outlet before starting this repair.
Step 2. Using a Torx-20 screwdriver, take out the bolts at the back of the machine securing the top panel. Pull the panel backwards a few inches, then lift it off the cabinet.
Step 3. Lift the support rail off the cabinet and set it aside. Disconnect the wire harnesses attached to the pressure switch.
Step 4. Using a flat-blade screwdriver if needed, pry the pressure switch off the mounting bracket on the cabinet.
Step 5. Disconnect the tube from the pressure switch. Discard the old switch, then prepare the new one for installation by unpacking it.
Step 6. Push the pressure tube onto the new switch. Snap the pressure switch onto the mounting bracket.
Step 7. Place the support bracket on the cabinet. Remount the top panel on the machine, then secure it by applying the Torx screws.
Step 8. Plug your washing machine’s power cord to the outlet, then try running a wash cycle to ensure that the issue has been fixed.
6. Faulty Control Board
If your Asko washing machine is not filling, the final probable cause is a damaged control board. If your washer’s control board is burnt, follow the steps below to replace it…
Step 1. Ensure that you disconnect your machine from the outlet before starting this repair, in order to prevent electrocution.
Step 2. Using your Torx-20 screwdriver, take out the bolts at the back of the machine holding the top panel. Pull the panel backwards, then lift it off the machine.
Step 3. Release the retaining tabs holding the control panel to the front of the cabinet using a flat-blade screwdriver.
Step 4. Pry the control panel off the mounting bracket. Detach the wires connected to the control board (ensure that you note where each plug goes).
Step 5. Pry the rubber gasket off the control panel. Using a flat-blade screwdriver, pry the control board off the panel. Pull the board off, then set it aside.
Step 6. Prepare your new control board assembly by taking it out of its packaging. Transfer the control knob and buttons from the old board to the new one.
Step 7. Peel the protective cover on the display of the new board. Mount the Start/Stop button and cover on the new board.
Step 8. Snap the new control board into the control panel. Using a small flat-blade screwdriver, push the rubber gasket into the groove of the control panel.
Step 9. Plug each wire harness into its appropriate terminal on the control board. Snap the control panel onto the front of the cabinet.
Step 10. Ensure that the support bracket is properly in place at the top of the washing machine. Remount the top panel, then use your Torx screwdriver to apply the bolts.
Step 11. Reconnect your washing machine to the power outlet. To ensure that the issue has been fixed, try running a wash cycle.