Asko Washing Machine Will Not Spin [4 Problems & Proven Solutions]

If your Asko washing machine will not spin, you’ve come to the right place. This detailed guide lists the causes of this issue and provides steps to deal with them…

asko washing machine will not spin

Asko Washing Machine Will Not Spin — How To Fix

If your Asko washing machine will not spin, the following are causes to look for…

1. Broken Drive Belt

The drive belt is looped around the pulley at the back of the tub. If the belt snaps, your Asko washing machine will not spin. Follow the steps below to replace a damaged drive belt…

Step 1. In order to prevent any chances of electrocution, it is advised that you disconnect your washing machine’s power cord from the outlet before starting this procedure.

Step 2. Using a Torx screwdriver, take out the bolts at the back of the machine securing the rear access panel.

Step 3. Carefully lift the rear panel off the cabinet, then set it aside. While rotating the drive pulley slowly, unhook the belt from two pulleys (if still intact).

Step 4. Discard the old drive belt, then prepare the new one for installation by unpacking it.

Step 5. With the grooved side turned inwards, loop the drive belt around the motor pulley and drive pulley.

Step 6. Lift the rear access panel, then snap it onto the cabinet. Secure the panel by applying the bolts.

Step 7. Reconnect your washing machine to the power outlet, then try running a spin cycle to ensure that the problem has been fixed.

2. Damaged Drive Pulley

The drive pulley is mounted on the tub shaft at the back of the drum. If this pulley is cracked or damaged, your Asko washing machine will not spin. The steps below show you how to replace this part…

Step 1. Before starting this repair, ensure that you disconnect your washing machine from the power outlet in order to prevent electrocution.

See also  Amana Washing Machine Not Turning On [Proven Solutions]

Step 2. Use a Torx-20 screwdriver to take out the bolts at the back of the cabinet securing the rear panel. Lift the rear panel off the machine, then set it aside.

Step 3. Rotate the drive pulley slowly, while unhooking the drive belt. Using a 16mm socket wrench, loosen the bolt holding the drive pulley to the tub shaft.

Step 4. Take the pulley wheel off, then discard it. Prepare the new pulley wheel for installation by unpacking it.

Step 5. Slide the new pulley wheel onto the shaft, then secure it by applying the 16mm bolt.

Step 6. Loop the drive belt around the motor pulley and drive pulley (ensure that the grooved side of the belt is turned inwards).

Step 7. Snap the rear access panel onto the cabinet, then apply the screws. Plug your washer’s power cord into the outlet. Try turning the machine on and running a wash cycle to ensure that the issue has been fixed.

Check out these other articles…

KitchenAid Washing Machine Door [6 Issues & Proven Solutions]

KitchenAid Washing Machine Filter [3 Issues & Quick Solutions]

KitchenAid Washing Machine Is Stuck On Rinse [4 Causes & Quick Solutions]

KitchenAid Washing Machine Is Making Noise [8 Causes & Proven Solutions]

Asko Washing Machine Will Not Drain [2 Causes & Quick Solutions]

Asko Washing Machine Is Not Filling With Water [6 Problems & Proven Solutions]

Asko Washing Machine Is Leaking [6 Problems & Proven Solutions]

3. Faulty Door Lock

As safety precaution, your Asko washing machine will not spin unless the door is properly locked. Ensure that you firmly shut your washer’s door before starting a cycle.

If your washing machine door isn’t locking, you’ll need to replace the door switch. Follow the steps below to do this…

Step 1. Disconnect your appliance from the outlet before starting this repair, in order to avoid electrocution.

Step 2. Loosen the nuts at the back of the machine securing the top panel, using a Torx screwdriver.

See also  How To Replace Water Inlet Valve On Frigidaire Washer [Quick Guide]

Step 3. Slide the panel backwards, then lift it off the cabinet. With the help of a small flat-blade screwdriver, pry the control panel off the mounting bracket. Set the control panel on top of the cabinet.

Step 4. Pry the lower front access panel open using a flat-blade screwdriver. Place a small container underneath the emergency drain tube.

Step 5. Pull the cap off the tube, then let any water stuck in the machine drain out. Once all the water drains out, push the cap onto the hose.

Step 6. With someone assisting you, carefully tip your machine backwards and place a support underneath.

Step 7. Take out the bolts at the bottom of the front panel. Lower the appliance onto its feet.

Step 8. Loosen the bolts at the top of the front panel. Lift the front panel off the cabinet carefully, then set it aside.

Step 9. Using a small flat-blade screwdriver, lift the lock lever at the front of the drum. Open the door of the machine.

Step 10. Using your Torx screwdriver, take out the bolts securing the tub cover. Detach the cover from the tub.

Step 11. Take out the remaining bolts securing the door switch to the front of the drum. Detach the plastic shield from the door switch.

Step 12. Push the door lock assembly out of place, then disconnect the wire harness plugged in.

Step 13. Discard the old door switch, then prepare the new one for installation by unpacking it.

Step 14. Plug the wire harness into the new door lock. Push the door lock into place in the cabinet, then snap the shield on.

Step 15. Push the tub cover back into place, then secure it by tightening the Torx screws. Secure the new door lock by applying the bolts.

Step 16. Close the door of your machine. Lift the front panel, then snap it onto the cabinet. Use your screwdriver to apply the bolts at the top of the panel.

Step 17. Tip your machine backwards, then tighten the screws at the bottom of the front panel. Set your washer back onto its feet.

See also  Washing Machine Draining [Problems Solved]

Step 18. Snap the control panel back onto the mounting bracket. Ensure that the top support brace is properly mounted on the cabinet.

Step 19. Place the top panel on the cabinet, then push it forwards. Secure the panel by tightening the Torx screws.

Step 20. Reconnect your washing machine to the power outlet, then turn it on. To ensure that the problem has been fixed, try running a spin cycle.

4. Damaged Drive Motor

The drive motor is the main part responsible for making the drum turn. If this part burns or gets damaged, your Asko washing machine will not spin. The steps below show you how to replace this part…

Step 1. In order to avoid electrocution, it is advised that you disconnect your machine from the outlet before starting this repair.

Step 2. Use a Torx-20 screwdriver to take out the bolts at the back of the machine securing the rear panel. Lift the panel off the cabinet, then set it aside.

Step 3. Rotate the drive pulley slowly, then unhook the drive belt. Disconnect the wire harness attached to the drive motor at the bottom of the tub.

Step 4. Loosen the bolts securing the drive motor to the bottom of the tub using a 13mm socket wrench. Lift the motor off the tub, then pull it out of the cabinet.

Step 5. Take your new washer drive motor out of its packaging. Transfer the support rods on the old motor to the new one.

Step 6. Carefully mount the drive motor at the bottom of the tub, then secure it by applying the 13mm bolts.

Step 7. Plug the wire harness into the new drive motor. With the grooved side facing inwards, loop the drive belt around the motor pulley and drive pulley.

Step 8. Snap the rear access panel onto the cabinet, then apply the bolts with your Torx screwdriver.

Step 9. Carefully remount the rear access panel onto the cabinet, then apply the Torx screws.

Step 10. Plug your appliance back into the outlet, then try running a cycle to ensure that the problem has been fixed.